Eiji Hiraki
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Eiji Hiraki has a total of 58 co-authors. Here are the top co-authors by number of shared publications:
- Kazuhiro Umetani
Faculty of Information Science and Electric Engineering, Kyushu University, Nishi-ku, Japan
13 shared publications - Momoko Nakaoka
Department of Electrical and Electronic System Engineering, The Graduate School of Science and Engineering, Yamaguchi University, 2-16-1 Tokiwa-dai, Ube City, Yamaguchi 755-8611, Japan
8 shared publications - Masataka Ishihara
Faculty of Life, Environment, Natural Science and Technology, Okayama University, Okayama, Japan
5 shared publications - Takayuki Kusumi
Graduate School of Natural Science and Technology, Okayama University, Kita-ku, Japan
3 shared publications - Toshihiko Tanaka
Department of Chemistry and Biochemistry Fukushima College National Institute of Technology 30 Aza‐Nagao, Tairakamiarakawa Iwaki Fukushima 970‐8034 Japan
3 shared publications - Masayuki Okamoto
Graduate School of Science and Engineering, Yamaguchi University
2 shared publications
Latest Publications
- Open Access
- 28 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 82069-82080
Measurement-Based Parasitic Inductance Network Identification for Multichip Power Modules Based on Inductance Matrix of Loop Wiring Paths
Internal parasitic inductance is a critical factor in fast-switching silicon carbide (SiC) power modules, making its accurate extraction essential for reliable design. Although measurement-based extraction methods are highly desirable for quality assurance, their practical difficulty has led to the widespread use of simulation-based partial element equivalent circuit (PEEC) methods. The PEEC method evaluates a branch-based inductance matrix, enabling detailed extraction that fully accounts for the magnetic coupling of each branch. However, applying the PEEC method in experimental setups is challenging because directly measuring the extremely small self-inductances of each branch makes the results highly susceptible to the parasitic inductance of measurement cables and requires a large number of measurements. To overcome these limitations, this study proposes extracting the parasitic inductance network by measuring the inductance matrix of closed loops formed by internal wiring paths, rather than the conventional branch-based matrix. Because these closed loops provide a closed current path, capacitors can be inserted to induce parallel resonance with the parasitic inductances, enabling extremely small inductances to be accurately measured as high impedances. Furthermore, this approach reduces the number of required measurements, while still accounting for magnetic couplings similar to the PEEC method. The validity and accuracy of the proposed methodology are demonstrated through experimental verification using a prototype SiC power module.
- 28 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 14, 82069-82080
Open AccessMeasurement-Based Parasitic Inductance Network Identification for Multichip Power Modules Based on Inductance Matrix of Loop Wiring Paths
Internal parasitic inductance is a critical factor in fast-switching silicon carbide (SiC) power modules, making its accurate extraction essential for reliable design. Although measurement-based extraction methods are highly desirable for quality assurance, their practical difficulty has led to the widespread use of simulation-based partial element equivalent circuit (PEEC) methods. The PEEC method evaluates a branch-based inductance matrix, enabling detailed extraction that fully accounts for the magnetic coupling of each branch. However, applying the PEEC method in experimental setups is challenging because directly measuring the extremely small self-inductances of each branch makes the results highly susceptible to the parasitic inductance of measurement cables and requires a large number of measurements. To overcome these limitations, this study proposes extracting the parasitic inductance network by measuring the inductance matrix of closed loops formed by internal wiring paths, rather than the conventional branch-based matrix. Because these closed loops provide a closed current path, capacitors can be inserted to induce parallel resonance with the parasitic inductances, enabling extremely small inductances to be accurately measured as high impedances. Furthermore, this approach reduces the number of required measurements, while still accounting for magnetic couplings similar to the PEEC method. The validity and accuracy of the proposed methodology are demonstrated through experimental verification using a prototype SiC power module.
- Open Access
- 10 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 127126-127141
Load Observing System Based on Wave Reflection for Soft-Switching Control of MHz-Frequency Resonant Inverter Against Load Fluctuations
Applying MHz-frequency inverters to radio frequency (RF) power sources for plasma applications has been challenging because capacitive loads caused by load fluctuations cause destructive hard-switching. This paper proposes a MHz-frequency load impedance estimation method for soft-switching control. The proposed system estimates the load impedance by utilizing a directional coupler that is typically built into an RF power source to observe traveling and reflected waves. Therefore, unlike typical low-frequency power electronics systems, the proposed system does not require output current sensors which are not suitable for MHz-frequencies. In the experiment, the proposed method was tested using the auxiliary switch-inductor circuit of a 3.75MHz gallium nitride (GaN) full-bridge inverter as the control target. Capacitive load detection by the proposed method was experimentally verified, and soft-switching control was realized under capacitive load. The transient response of the control under a fluctuating load that changes from inductive to capacitive was also measured. The inverter transitioned to soft-switching within 2.31μs after a load change, and hard-switching took only 8 cycles.
- 10 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 13, 127126-127141
Open AccessLoad Observing System Based on Wave Reflection for Soft-Switching Control of MHz-Frequency Resonant Inverter Against Load Fluctuations
Applying MHz-frequency inverters to radio frequency (RF) power sources for plasma applications has been challenging because capacitive loads caused by load fluctuations cause destructive hard-switching. This paper proposes a MHz-frequency load impedance estimation method for soft-switching control. The proposed system estimates the load impedance by utilizing a directional coupler that is typically built into an RF power source to observe traveling and reflected waves. Therefore, unlike typical low-frequency power electronics systems, the proposed system does not require output current sensors which are not suitable for MHz-frequencies. In the experiment, the proposed method was tested using the auxiliary switch-inductor circuit of a 3.75MHz gallium nitride (GaN) full-bridge inverter as the control target. Capacitive load detection by the proposed method was experimentally verified, and soft-switching control was realized under capacitive load. The transient response of the control under a fluctuating load that changes from inductive to capacitive was also measured. The inverter transitioned to soft-switching within 2.31μs after a load change, and hard-switching took only 8 cycles.
- 22 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (10) , 12047-12052
GaN-HEMT Power Module of Aluminum-Clad Printed Circuit Boards for Small Power Loop Inductance and High Cooling Performance
Gallium nitride high-electron-mobility transistors (GaN-HEMTs) are promising for high-speed switching capability and small on -resistance. However, large turn- off surge and limited cooling capability due to their small chip size are hindering their application to high power conversion. To solve these problems, this letter proposes a novel power module structure with small power loop inductance and small thermal resistance based on recently proposed power module structures. The proposed structure comprises two aluminum-clad printed circuit boards (PCBs) that sandwich the GaN-HEMT devices. These PCBs generate eddy current inside the aluminum base to reduce power loop inductance and provide an additional thermal path to improve the cooling performance. These features were tested by an experiment that compared 3-kW half-bridge prototype power modules of the proposed and conventional structures. As a result, the proposed structure revealed power loop inductance of 1.4 nH and thermal resistance of 0.72 K/W, which corresponded to a reduction by 53% and 20%, respectively, compared to the conventional structure.
- 22 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Power Electronics
- Vol. 39 (10) , 12047-12052
GaN-HEMT Power Module of Aluminum-Clad Printed Circuit Boards for Small Power Loop Inductance and High Cooling Performance
Gallium nitride high-electron-mobility transistors (GaN-HEMTs) are promising for high-speed switching capability and small on -resistance. However, large turn- off surge and limited cooling capability due to their small chip size are hindering their application to high power conversion. To solve these problems, this letter proposes a novel power module structure with small power loop inductance and small thermal resistance based on recently proposed power module structures. The proposed structure comprises two aluminum-clad printed circuit boards (PCBs) that sandwich the GaN-HEMT devices. These PCBs generate eddy current inside the aluminum base to reduce power loop inductance and provide an additional thermal path to improve the cooling performance. These features were tested by an experiment that compared 3-kW half-bridge prototype power modules of the proposed and conventional structures. As a result, the proposed structure revealed power loop inductance of 1.4 nH and thermal resistance of 0.72 K/W, which corresponded to a reduction by 53% and 20%, respectively, compared to the conventional structure.
- Open Access
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 98175-98188
Feasibility of Active Reactance Compensator for Autonomously Maximizing Repeater Coil Current of Wireless Power Transfer System Against Variations in Resonant Frequency and Magnetic Coupling Intensity
In resonant inductive coupling wireless power transfer systems, a repeater resonator is crucial in expanding the charging area, enabling efficient power supply to receivers, such as small Internet of Things (IoT) devices sparsely distributed in a wide area. However, the repeater current is highly susceptible to deviations in resonance frequency due to manufacturing tolerance and aging, as well as to the magnetic coupling between the transmitter and repeater coils, potentially leading to insufficient amplitude. Consequently, the magnetic field generated by the repeater decreases and the receiver may be difficult to obtain sufficient power from the transmitter via the repeater. To address this problem, this paper proposes a wireless power transfer system with active reactance compensators incorporated in the repeater and the transmitter. The proposed system can equivalently adjust the resonant frequencies of the transmitter and repeater to stably maximize the repeater coil current regardless of the variations in the resonant frequency and the magnetic coupling intensity. Experiments successfully verify that the proposed system can provide a more stable and larger repeater current and output power than the conventional system against the variations in the magnetic field intensity and the resonant frequency of the repeater, validating the feasibility of the proposed system for practical utilization of the repeater in expanding the charging area.
- 15 July 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Access
- Vol. 12, 98175-98188
Open AccessFeasibility of Active Reactance Compensator for Autonomously Maximizing Repeater Coil Current of Wireless Power Transfer System Against Variations in Resonant Frequency and Magnetic Coupling Intensity
In resonant inductive coupling wireless power transfer systems, a repeater resonator is crucial in expanding the charging area, enabling efficient power supply to receivers, such as small Internet of Things (IoT) devices sparsely distributed in a wide area. However, the repeater current is highly susceptible to deviations in resonance frequency due to manufacturing tolerance and aging, as well as to the magnetic coupling between the transmitter and repeater coils, potentially leading to insufficient amplitude. Consequently, the magnetic field generated by the repeater decreases and the receiver may be difficult to obtain sufficient power from the transmitter via the repeater. To address this problem, this paper proposes a wireless power transfer system with active reactance compensators incorporated in the repeater and the transmitter. The proposed system can equivalently adjust the resonant frequencies of the transmitter and repeater to stably maximize the repeater coil current regardless of the variations in the resonant frequency and the magnetic coupling intensity. Experiments successfully verify that the proposed system can provide a more stable and larger repeater current and output power than the conventional system against the variations in the magnetic field intensity and the resonant frequency of the repeater, validating the feasibility of the proposed system for practical utilization of the repeater in expanding the charging area.
- 5 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (4) , 5248-5261
Analytical Derivation of Phase-Current Waveform for Elimination of Torque and Input-Current Ripples of Switched Reluctance Motor Operating Under Magnetic Saturation
Switched reluctance motors (SRMs) have recently attracted researchers attention owing to their robust mechanical construction, high thermal tolerance, and strong cost-effectiveness, which are promising for vehicle propulsion. However, they tend to generate large ripples in the torque and input currents to the inverter; this deteriorates the driving comfort, and damages the battery lifetime. Preceding studies have investigated using the phase currents of SRMs to eliminate these ripples. However, these studies had difficulties in sufficiently eliminating these ripples in operations under magnetic saturation. This study further evolves one of these preceding studies, and proposes a derivation method for the phase-current waveform for improving the elimination of the torque and input-current ripples in operation under magnetic saturation. The proposed method analytically determines the phase-current waveform based on a nonlinear behavior model of the SRM while considering the magnetic saturation. A finite-element-method-based simulation and experiment are performed to evaluate the proposed method. These results reveal the successful reduction of the torque and input-current ripples under the magnetic saturation relative to a preceding study, supporting the appropriateness of the proposed method.
- 5 May 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (4) , 5248-5261
Analytical Derivation of Phase-Current Waveform for Elimination of Torque and Input-Current Ripples of Switched Reluctance Motor Operating Under Magnetic Saturation
Switched reluctance motors (SRMs) have recently attracted researchers attention owing to their robust mechanical construction, high thermal tolerance, and strong cost-effectiveness, which are promising for vehicle propulsion. However, they tend to generate large ripples in the torque and input currents to the inverter; this deteriorates the driving comfort, and damages the battery lifetime. Preceding studies have investigated using the phase currents of SRMs to eliminate these ripples. However, these studies had difficulties in sufficiently eliminating these ripples in operations under magnetic saturation. This study further evolves one of these preceding studies, and proposes a derivation method for the phase-current waveform for improving the elimination of the torque and input-current ripples in operation under magnetic saturation. The proposed method analytically determines the phase-current waveform based on a nonlinear behavior model of the SRM while considering the magnetic saturation. A finite-element-method-based simulation and experiment are performed to evaluate the proposed method. These results reveal the successful reduction of the torque and input-current ripples under the magnetic saturation relative to a preceding study, supporting the appropriateness of the proposed method.
- 18 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (4) , 3898-3910
Autonomous System Concept of Multiple-Receiver Inductive Coupling Wireless Power Transfer for Output Power Stabilization Against Cross-Interference Among Receivers and Resonance Frequency Tolerance
Multiple-receiver resonant inductive coupling wireless power transfer (RIC-WPT) technique is emerging as a promising charging method for multiple household appliances, mobile devices, and wearable devices. However, this technique often suffers from output power fluctuation owing to the cross-interference among receivers as well as the manufacturing and aging tolerance of the resonant frequency (i.e., resonant frequency tolerance). This paper proposes an autonomous RIC-WPT system concept to solve this difficulty. The proposed concept addresses the cross-interference and resonant frequency tolerance by incorporating two functions: 1. The amplitude of the transmitter current is controlled to have a constant amplitude; 2. The phase of each receiver current is controlled to be orthogonal to that of the transmitter current by using an active reactance compensator installed in each receiver. The experiment of a two-receiver RIC-WPT system successfully verified that the two functions of the proposed system concept can stabilize the output voltage against the cross-interference and resonant frequency tolerance.
- 18 May 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (4) , 3898-3910
Autonomous System Concept of Multiple-Receiver Inductive Coupling Wireless Power Transfer for Output Power Stabilization Against Cross-Interference Among Receivers and Resonance Frequency Tolerance
Multiple-receiver resonant inductive coupling wireless power transfer (RIC-WPT) technique is emerging as a promising charging method for multiple household appliances, mobile devices, and wearable devices. However, this technique often suffers from output power fluctuation owing to the cross-interference among receivers as well as the manufacturing and aging tolerance of the resonant frequency (i.e., resonant frequency tolerance). This paper proposes an autonomous RIC-WPT system concept to solve this difficulty. The proposed concept addresses the cross-interference and resonant frequency tolerance by incorporating two functions: 1. The amplitude of the transmitter current is controlled to have a constant amplitude; 2. The phase of each receiver current is controlled to be orthogonal to that of the transmitter current by using an active reactance compensator installed in each receiver. The experiment of a two-receiver RIC-WPT system successfully verified that the two functions of the proposed system concept can stabilize the output voltage against the cross-interference and resonant frequency tolerance.
- 25 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 439-446
Feasibility of Sinusoidal Flux Drive Design of Reluctance Motor for Reducing Torque and Input Current Ripples with Three-Leg Inverter
Reluctance motors, represented by the switched reluctance motor (SRM) and the synchronous reluctance motor (SynRM), are attractive for vehicle propulsion owing to their high thermal tolerance and simple mechanical construction. However, the SRM exhibits large torque and large input current ripples, deteriorating driving comfort and battery lifespan. Furthermore, a driving system of the SRM requires the special inverter topology with additional switching or rectifying devices, leading to the cost-up. Meanwhile, the SynRM does not have these drawbacks, although this motor tends to be difficult to cover the wide range of the torque and the rotation speed required for vehicle propulsion because of large phase flux induction. To solve the obstacles of these conventional reluctance motors, this paper proposes a novel reluctance motor. The proposed reluctance motor is based on magnetization by the sinusoidal phase flux waveform, whereby the torque and input current ripples are eliminated using a common three-leg inverter without inducing large phase magnetic flux. This paper presents the operating principles of the proposed reluctance motor as well as analysis and simulation results in comparison with the SRM and the SynRM. As a result, the proposed reluctance motor is elucidated to reduce the torque and input current ripples with the three-leg inverter. Furthermore, the proposed reluctance motor can improve the torque range and rotating speed range compared to the SynRM because of the sinusoidal flux waveform with reduced amplitude. These results imply feasibility of the proposed motor for vehicle propulsion.
- 25 April 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE)
- p. 439-446
Feasibility of Sinusoidal Flux Drive Design of Reluctance Motor for Reducing Torque and Input Current Ripples with Three-Leg Inverter
Reluctance motors, represented by the switched reluctance motor (SRM) and the synchronous reluctance motor (SynRM), are attractive for vehicle propulsion owing to their high thermal tolerance and simple mechanical construction. However, the SRM exhibits large torque and large input current ripples, deteriorating driving comfort and battery lifespan. Furthermore, a driving system of the SRM requires the special inverter topology with additional switching or rectifying devices, leading to the cost-up. Meanwhile, the SynRM does not have these drawbacks, although this motor tends to be difficult to cover the wide range of the torque and the rotation speed required for vehicle propulsion because of large phase flux induction. To solve the obstacles of these conventional reluctance motors, this paper proposes a novel reluctance motor. The proposed reluctance motor is based on magnetization by the sinusoidal phase flux waveform, whereby the torque and input current ripples are eliminated using a common three-leg inverter without inducing large phase magnetic flux. This paper presents the operating principles of the proposed reluctance motor as well as analysis and simulation results in comparison with the SRM and the SynRM. As a result, the proposed reluctance motor is elucidated to reduce the torque and input current ripples with the three-leg inverter. Furthermore, the proposed reluctance motor can improve the torque range and rotating speed range compared to the SynRM because of the sinusoidal flux waveform with reduced amplitude. These results imply feasibility of the proposed motor for vehicle propulsion.
- 4 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (3) , 2407-2420
Analytical Formulation of Copper Loss of Litz Wire With Multiple Levels of Twisting Using Measurable Parameters
Litz wire has been widely utilized in power transformers and inductors as a wire with low copper loss at high-frequency operation. The Litz wire is commonly made of many thin isolated strands twisted in multiple levels. Due to its complicated structure, the copper loss prediction of the Litz wire has been difficult, hindering the design optimization of the Litz wire structure. To overcome this difficulty, preceding studies have investigated the analytical copper loss models of the constituting elements of the Litz wire, i.e. the strands and the bundles of strands. The purpose of this paper is to propose an analytical copper loss model of the Litz wire by utilizing these preceding knowledge. The proposed model is formulated only with parameters that can be measured by basic testing instruments. Besides, the proposed model considers the bundle structure of the Litz wire, which affects the local ac current distribution, and the twisting pitch, which causes the inclination of the Litz wire strands. The proposed model was tested by comparing the analytical prediction and experimental measurements of the ac resistance of commercially available Litz wires. As a result, the predicted ac resistance showed good agreement with the measured ac resistance, suggesting the appropriateness of the proposed model.
- 4 March 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 57 (3) , 2407-2420
Analytical Formulation of Copper Loss of Litz Wire With Multiple Levels of Twisting Using Measurable Parameters
Litz wire has been widely utilized in power transformers and inductors as a wire with low copper loss at high-frequency operation. The Litz wire is commonly made of many thin isolated strands twisted in multiple levels. Due to its complicated structure, the copper loss prediction of the Litz wire has been difficult, hindering the design optimization of the Litz wire structure. To overcome this difficulty, preceding studies have investigated the analytical copper loss models of the constituting elements of the Litz wire, i.e. the strands and the bundles of strands. The purpose of this paper is to propose an analytical copper loss model of the Litz wire by utilizing these preceding knowledge. The proposed model is formulated only with parameters that can be measured by basic testing instruments. Besides, the proposed model considers the bundle structure of the Litz wire, which affects the local ac current distribution, and the twisting pitch, which causes the inclination of the Litz wire strands. The proposed model was tested by comparing the analytical prediction and experimental measurements of the ac resistance of commercially available Litz wires. As a result, the predicted ac resistance showed good agreement with the measured ac resistance, suggesting the appropriateness of the proposed model.
- 4 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Industrial Electronics Magazine
- Vol. 15 (1) , 140-154
Industrial Electronics Education: Past, Present, and Future Perspectives
- 4 February 2021
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Industrial Electronics Magazine
- Vol. 15 (1) , 140-154
Industrial Electronics Education: Past, Present, and Future Perspectives
- 11 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 56 (6) , 6384-6398
Simultaneous Tuning of Rotor Shape and Phase Current of Switched Reluctance Motors for Eliminating Input Current and Torque Ripples With Reduced Copper Loss
Switched reluctance motor (SRM) is recently emerging as a cost-effective but mechanically and thermally robust motor for vehicle propulsion. However, the conventional driving method of the SRM causes a large input current and torque ripples, both of which are scarcely acceptable for vehicle application. Recently, a promising driving method has been proposed that tunes the phase current to eliminate the input current and torque ripples simultaneously, although this method suffers from large copper loss when applied to the normal SRMs. To solve this problem, this paper proposes simultaneous tuning of the rotor shape in combination with the recently-proposed driving method, which includes only tuning of the phase current. Tuning of the rotor shape is targeted at minimizing the copper loss. Meanwhile, the stator structure is the same as the normal SRM design. The proposed approach was revealed to reduce the effective value of the phase current by 18% in simulation and by 23% in experiment compared with the recently-proposed driving method, without increasing the input current and torque ripples. This result suggests the effectiveness of tuning both the rotor shape and the phase current for applying SRMs to vehicle propulsion.
- 11 August 2020
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 56 (6) , 6384-6398
Simultaneous Tuning of Rotor Shape and Phase Current of Switched Reluctance Motors for Eliminating Input Current and Torque Ripples With Reduced Copper Loss
Switched reluctance motor (SRM) is recently emerging as a cost-effective but mechanically and thermally robust motor for vehicle propulsion. However, the conventional driving method of the SRM causes a large input current and torque ripples, both of which are scarcely acceptable for vehicle application. Recently, a promising driving method has been proposed that tunes the phase current to eliminate the input current and torque ripples simultaneously, although this method suffers from large copper loss when applied to the normal SRMs. To solve this problem, this paper proposes simultaneous tuning of the rotor shape in combination with the recently-proposed driving method, which includes only tuning of the phase current. Tuning of the rotor shape is targeted at minimizing the copper loss. Meanwhile, the stator structure is the same as the normal SRM design. The proposed approach was revealed to reduce the effective value of the phase current by 18% in simulation and by 23% in experiment compared with the recently-proposed driving method, without increasing the input current and torque ripples. This result suggests the effectiveness of tuning both the rotor shape and the phase current for applying SRMs to vehicle propulsion.