Jisan Ahn
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jisan Ahn has a total of 5 co-authors. Here are the top co-authors by number of shared publications:
- Hyung-Min Lee
Korea University
3 shared publications - Kyeongho Eom
School of Electrical Engineering, Korea University, Seoul, South Korea
1 shared publication Minil Kang
School of Electrical Engineering, Korea University, Seoul, South Korea
1 shared publication- Minjae Kim
School of Electrical Engineering, Korea University, Seoul, South Korea
1 shared publication - Woojoong Jung
School of Electrical Engineering, Korea University, Seoul, South Korea
1 shared publication
Latest Publications
- 11 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (3) , 562-576
A 13.56-MHz 93.5%-Efficiency Optimal On/Off Timing Tracking Active Rectifier With Digital Feedback-Based Adaptive Delay Control
This paper presents an adaptive active rectifier with digital feedback delay controllers (DFDC) which quickly tracks optimal on/off timing against input voltage and load variations. To efficiently generate the on/off transition, the proposed active rectifier adopts dynamically controlled coarse/fine delay lines rather than using conventional power-hungry static comparators, while removing the risk of unwanted multiple driving pulses to pass transistors. DFDC conducts the dual-loop digital feedback to independently adjust on/off timing with high-speed 13.56-MHz loop bandwidth, improving the voltage conversion ratio (VCR) and power conversion efficiency (PCE). DFDC can enable real-time power-saving mode control that automatically masks clock-toggling to non-essential blocks to minimize dynamic power loss while driving power transistors. To validate the efficacy of the proposed adaptive rectifier during digital feedback and settling procedures, experiments were carried out with 0.25 μm CMOS prototype at the carrier frequency of 13.56-MHz, input voltages between 1.7 and 2.6 V, and load ranges from 0.33 to 2.2 kΩ. The proposed active rectifier employing DFDC achieves a peak PCE of 93.5% and the peak VCR of 96.3% at the output power of 12.52 mW and 2.02 mW, respectively.
- 11 September 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 19 (3) , 562-576
A 13.56-MHz 93.5%-Efficiency Optimal On/Off Timing Tracking Active Rectifier With Digital Feedback-Based Adaptive Delay Control
This paper presents an adaptive active rectifier with digital feedback delay controllers (DFDC) which quickly tracks optimal on/off timing against input voltage and load variations. To efficiently generate the on/off transition, the proposed active rectifier adopts dynamically controlled coarse/fine delay lines rather than using conventional power-hungry static comparators, while removing the risk of unwanted multiple driving pulses to pass transistors. DFDC conducts the dual-loop digital feedback to independently adjust on/off timing with high-speed 13.56-MHz loop bandwidth, improving the voltage conversion ratio (VCR) and power conversion efficiency (PCE). DFDC can enable real-time power-saving mode control that automatically masks clock-toggling to non-essential blocks to minimize dynamic power loss while driving power transistors. To validate the efficacy of the proposed adaptive rectifier during digital feedback and settling procedures, experiments were carried out with 0.25 μm CMOS prototype at the carrier frequency of 13.56-MHz, input voltages between 1.7 and 2.6 V, and load ranges from 0.33 to 2.2 kΩ. The proposed active rectifier employing DFDC achieves a peak PCE of 93.5% and the peak VCR of 96.3% at the output power of 12.52 mW and 2.02 mW, respectively.
- 30 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (2) , 400-410
A 13.56-MHz Wireless Power and Data Transfer System With Current-Modulated Energy-Reuse Back Telemetry and Energy-Adaptive Voltage Regulation
Wireless power/data transfer (WPDT) through an inductive link has been an essential technique in a wide range of applications, especially for implantable medical devices (IMD), which require high power efficiency for safe operation and high data rate for continuous telemetry. This article proposes an efficient WPDT system with current-modulated energy-reuse back telemetry (ER-BT), which can induce instantaneous changes of load impedance at Rx for BT data rate up to 1 Mb/s, while reusing BT current to supply the load, improving the system power efficiency. The WPDT system also utilizes an energy-adaptive dual-input low-dropout regulator (LDO) to store and optimally reuse the BT energy for IMDs against data rate or load variations. The proposed system was fabricated in a 180-nm 1.8-/5-V standard CMOS process and measured with a coupled-coil inductive link operating at 13.56 MHz to provide a supply voltage of 1.8 V for IMDs. The proposed ER-BT can save the energy up to 42% during the BT operation compared to energy losses of the conventional short-coil (SC) BT when the inductive link provides the input power of 3.05 mW.
- 30 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Solid-State Circuits
- Vol. 58 (2) , 400-410
A 13.56-MHz Wireless Power and Data Transfer System With Current-Modulated Energy-Reuse Back Telemetry and Energy-Adaptive Voltage Regulation
Wireless power/data transfer (WPDT) through an inductive link has been an essential technique in a wide range of applications, especially for implantable medical devices (IMD), which require high power efficiency for safe operation and high data rate for continuous telemetry. This article proposes an efficient WPDT system with current-modulated energy-reuse back telemetry (ER-BT), which can induce instantaneous changes of load impedance at Rx for BT data rate up to 1 Mb/s, while reusing BT current to supply the load, improving the system power efficiency. The WPDT system also utilizes an energy-adaptive dual-input low-dropout regulator (LDO) to store and optimally reuse the BT energy for IMDs against data rate or load variations. The proposed system was fabricated in a 180-nm 1.8-/5-V standard CMOS process and measured with a coupled-coil inductive link operating at 13.56 MHz to provide a supply voltage of 1.8 V for IMDs. The proposed ER-BT can save the energy up to 42% during the BT operation compared to energy losses of the conventional short-coil (SC) BT when the inductive link provides the input power of 3.05 mW.
- 19 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 16 (4) , 651-663
A Load-Insensitive Hybrid LSK Back Telemetry System With Slope-Based Demodulation for Inductively Powered Biomedical Devices
This paper presents a hybrid load-shift keying (LSK) modulation for a load-insensitive back telemetry system to realize near-constant voltage changes in a primary coil ( L1 ) against a wide range of load variations. The hybrid-LSK-enabled full-wave rectifier enables the sequential combination of open- and short-coil functions for hybrid-LSK modulation in addition to wireless power conversion operation. Load-insensitive L1 voltage changes can be demodulated using the proposed slope- based demodulator, which utilizes the threshold slope of L1 voltage changes over the back data pulse width, enabling robust data recovery regardless of the load conditions. The 0.56-mm 2 0.18-μm standard CMOS hybrid-LSK prototype demonstrated that the variation of L1 voltage changes could be minimized to 60 mV under load changes between 50 Ω and 50 kΩ at coil separation distance of 10 mm, achieving 88.2% reduction compared to the conventional short-coil LSK with 510 mV variation. The proposed back telemetry system also achieved a bit error rate (BER) of < 9.1 × 10 −10 under load ranges from 50 Ω to 50 kΩ and data rate of 1 Mbps, ensuring reliable back data recovery against load variations.
- 19 July 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Biomedical Circuits and Systems
- Vol. 16 (4) , 651-663
A Load-Insensitive Hybrid LSK Back Telemetry System With Slope-Based Demodulation for Inductively Powered Biomedical Devices
This paper presents a hybrid load-shift keying (LSK) modulation for a load-insensitive back telemetry system to realize near-constant voltage changes in a primary coil ( L1 ) against a wide range of load variations. The hybrid-LSK-enabled full-wave rectifier enables the sequential combination of open- and short-coil functions for hybrid-LSK modulation in addition to wireless power conversion operation. Load-insensitive L1 voltage changes can be demodulated using the proposed slope- based demodulator, which utilizes the threshold slope of L1 voltage changes over the back data pulse width, enabling robust data recovery regardless of the load conditions. The 0.56-mm 2 0.18-μm standard CMOS hybrid-LSK prototype demonstrated that the variation of L1 voltage changes could be minimized to 60 mV under load changes between 50 Ω and 50 kΩ at coil separation distance of 10 mm, achieving 88.2% reduction compared to the conventional short-coil LSK with 510 mV variation. The proposed back telemetry system also achieved a bit error rate (BER) of < 9.1 × 10 −10 under load ranges from 50 Ω to 50 kΩ and data rate of 1 Mbps, ensuring reliable back data recovery against load variations.