Siegfried Silber
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Siegfried Silber has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
- Bianca Wex
Unit Drives, LCM, Linz, Österreich
2 shared publications - Wolfgang Gruber
Johannes Kepler University Linz, Linz, Austria
2 shared publications Alexander Dorninger
Linz Center of Mechatronics GmbH, Austria
1 shared publicationArmin Fohler
Linz Center of Mechatronics GmbH, Austria
1 shared publicationDaniel Reischl
Linz Center of Mechatronics GmbH, Austria
1 shared publicationGerd Bramerdorfer
Johannes Kepler University, Austria
1 shared publication
Latest Publications
- 28 March 2025
- Published by Springer Nature in e+i Elektrotechnik und Informationstechnik
- Vol. 142 (2) , 176-186
Herausforderungen in der Entwicklung und Optimierung von Hochgeschwindigkeitsantrieben
- 28 March 2025
- Published by Springer Nature in e+i Elektrotechnik und Informationstechnik
- Vol. 142 (2) , 176-186
Herausforderungen in der Entwicklung und Optimierung von Hochgeschwindigkeitsantrieben
- 19 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (4) , 4237-4247
Fully Automatized PWM Loss Calculation in Multiphase PMSM and Experimental Verification
A very simple and therefore wide-spread way to control motor speed and torque is to regulate the stator voltage by pulsewidth modulation (PWM). Depending on the modulation type, number of inverter levels, and modulation index of the PWM, various spectral components occur in the supply signal and inject ripple current in the motor phases. This current distortion can cause significant additional losses in the stator and rotor core, permanent magnets, and windings of an electric machine. Therefore, it is important to consider these losses in an early design stage. In this work, an efficient calculation method for harmonics of multilevel PWM signals and generated phase currents with different modulation types is presented. The PWM losses are calculated via 2-D finite element method analyses. The calculation and simulation workflow is realized within the software tool SyMSpace and applied to a three-phase permanent magnetic synchronous machine (PMSM). Loss measurements at different PWM frequencies and load points are conducted on a 3-phase PMSM. Since simulation and measurement results show good accordance, the proposed methods could be validated.
- 19 April 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Industry Applications
- Vol. 58 (4) , 4237-4247
Fully Automatized PWM Loss Calculation in Multiphase PMSM and Experimental Verification
A very simple and therefore wide-spread way to control motor speed and torque is to regulate the stator voltage by pulsewidth modulation (PWM). Depending on the modulation type, number of inverter levels, and modulation index of the PWM, various spectral components occur in the supply signal and inject ripple current in the motor phases. This current distortion can cause significant additional losses in the stator and rotor core, permanent magnets, and windings of an electric machine. Therefore, it is important to consider these losses in an early design stage. In this work, an efficient calculation method for harmonics of multilevel PWM signals and generated phase currents with different modulation types is presented. The PWM losses are calculated via 2-D finite element method analyses. The calculation and simulation workflow is realized within the software tool SyMSpace and applied to a three-phase permanent magnetic synchronous machine (PMSM). Loss measurements at different PWM frequencies and load points are conducted on a 3-phase PMSM. Since simulation and measurement results show good accordance, the proposed methods could be validated.
- Open Access
The Flux-Based Sensorless Field-Oriented Control of Permanent Magnet Synchronous Motors without Integrational Drift
The magnitude of the rotor magnetic flux linkage and its spatial orientation within a permanent magnet synchronous motor directly define the angular position of the rotor and are thus used in many sensorless applications as the governing variables. The rotor magnetic flux linkage in the stator reference frame is represented by two orthogonal sinusoids whose amplitudes and phases are determined by the integration of the orthogonal components of the corresponding voltage, which, due to DC offsets and initial conditions at transient states, result in an integrational drift. This paper proposes a solution to the problem of such integrational drift in the form of a compensation based only on orthogonal properties of waveforms in the stator reference frame. That makes it completely independent of electrical parameters of the motor. As a result, the proposed compensation of the integrational drift does not require any optimization by the user and it is functional from a standstill. The effectiveness of the proposed compensation is demonstrated analytically, by a simulation, and an experiment on a real motor by a simple observer for the sensorless field-oriented control based on the voltage model in the stator reference frame.
Open AccessThe Flux-Based Sensorless Field-Oriented Control of Permanent Magnet Synchronous Motors without Integrational Drift
The magnitude of the rotor magnetic flux linkage and its spatial orientation within a permanent magnet synchronous motor directly define the angular position of the rotor and are thus used in many sensorless applications as the governing variables. The rotor magnetic flux linkage in the stator reference frame is represented by two orthogonal sinusoids whose amplitudes and phases are determined by the integration of the orthogonal components of the corresponding voltage, which, due to DC offsets and initial conditions at transient states, result in an integrational drift. This paper proposes a solution to the problem of such integrational drift in the form of a compensation based only on orthogonal properties of waveforms in the stator reference frame. That makes it completely independent of electrical parameters of the motor. As a result, the proposed compensation of the integrational drift does not require any optimization by the user and it is functional from a standstill. The effectiveness of the proposed compensation is demonstrated analytically, by a simulation, and an experiment on a real motor by a simple observer for the sensorless field-oriented control based on the voltage model in the stator reference frame.
- 28 July 2015
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering
- Vol. 230 (4) , 291-299
Coupled optimization in MagOpt
Optimizing mechatronic components is of increasing importance, e.g. for minimizing energy consumption and the use of rare materials. MagOpt is a modular software tool for the simulation and optimization of mechatronic components. Parametric design optimization can be carried out with various different optimization strategies like gradient-based methods or multi-objective evolutionary or genetic algorithms. MagOpt features a flexible structure for the storage of complex data and an open and modular interface to existing third-party programs. One such third-party program which can be used by MagOpt for the optimization of mechanic components is the multi-body software HOTINT. This article describes MagOpt and how it was coupled with HOTINT to optimize a rotor geometry.
- 28 July 2015
- Published by SAGE Publications in Proceedings of the Institution of Mechanical Engineers, Part I: Journal of Systems and Control Engineering
- Vol. 230 (4) , 291-299
Coupled optimization in MagOpt
Optimizing mechatronic components is of increasing importance, e.g. for minimizing energy consumption and the use of rare materials. MagOpt is a modular software tool for the simulation and optimization of mechatronic components. Parametric design optimization can be carried out with various different optimization strategies like gradient-based methods or multi-objective evolutionary or genetic algorithms. MagOpt features a flexible structure for the storage of complex data and an open and modular interface to existing third-party programs. One such third-party program which can be used by MagOpt for the optimization of mechanic components is the multi-body software HOTINT. This article describes MagOpt and how it was coupled with HOTINT to optimize a rotor geometry.