Zhaoming Mai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Zhaoming Mai has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Chenglong Tang
State Key Laboratory of Multiphase Flow in Power Engineering
6 shared publications - Yingtao Wu
State Key Laboratory of Multiphase Flow in Power Engineering, Xi'an Jiaotong University , Xi'an 710049, China
6 shared publications Zuohua Huang
4 shared publications- Zuohua Huang
State Key Laboratory of Multiphase Flow in Power Engineering, Xi’an Jiaotong University, Xi’an 710049, China
4 shared publications Chenglong Tang
2 shared publicationsWei Wang
2 shared publications
Latest Publications
- 25 June 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 253
Towards optimized excess air ratio and substitution rate for a dual fuel HPDI engine
- 25 June 2024
- Published by Elsevier in Applied Thermal Engineering
- Vol. 253
Towards optimized excess air ratio and substitution rate for a dual fuel HPDI engine
- 8 February 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (7) , 1-30
Understanding the Nonlinear Reactivity Promoting Effect of n-Heptane Addition on the Binary Mixture From Low to Intermediate Temperature: A Case of Methane/n-Heptane Mixtures
Adding high reactivity fuel in the binary mixtures generally exhibits nonlinear promoting effect on the ignition. To understand the effect of n-heptane (NC7H16) addition on the auto-ignition of methane (CH4) at low to intermediate temperatures, the ignition delay times (IDTs) of stoichiometric CH4/NC7H16 blends with varying NC7H16 concentrations were measured at temperatures from 600 to 1000 K, pressures of 20 and 40 bar. Detailed chemical kinetic mechanisms were validated against the newly measured IDTs. Adding NC7H16 in the binary mixture shows a nonlinear promoting effect on the IDTs: micro addition of NC7H16 can significantly reduce the IDTs of the binary mixture when the NC7H16 is lower than 20%. However, the decrease of the IDTs becomes much slower when further increasing the NC7H16 addition. Affected by the negative temperature coefficient behavior (NTC) of NC7H16, this nonlinear effect is particularly notable at around 795 K, the low boundary of the NTC region. To reveal the nonlinear reactivity promoting effect of NC7H16 addition on the binary mixture, reaction flux, ignition sensitivity, rate of production of the key radicals along with heat production analyses were conducted. Apart from contributing more ȮH production through the low-temperature chain-branching reaction pathways of NC7H16, adding NC7H16 also promotes the pre-ignition heat release of the binary mixture. The heat release raises the system temperature and further promotes the mixture ignition, enhancing the nonlinear effect at low temperatures.
- 8 February 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (7) , 1-30
Understanding the Nonlinear Reactivity Promoting Effect of n-Heptane Addition on the Binary Mixture From Low to Intermediate Temperature: A Case of Methane/n-Heptane Mixtures
Adding high reactivity fuel in the binary mixtures generally exhibits nonlinear promoting effect on the ignition. To understand the effect of n-heptane (NC7H16) addition on the auto-ignition of methane (CH4) at low to intermediate temperatures, the ignition delay times (IDTs) of stoichiometric CH4/NC7H16 blends with varying NC7H16 concentrations were measured at temperatures from 600 to 1000 K, pressures of 20 and 40 bar. Detailed chemical kinetic mechanisms were validated against the newly measured IDTs. Adding NC7H16 in the binary mixture shows a nonlinear promoting effect on the IDTs: micro addition of NC7H16 can significantly reduce the IDTs of the binary mixture when the NC7H16 is lower than 20%. However, the decrease of the IDTs becomes much slower when further increasing the NC7H16 addition. Affected by the negative temperature coefficient behavior (NTC) of NC7H16, this nonlinear effect is particularly notable at around 795 K, the low boundary of the NTC region. To reveal the nonlinear reactivity promoting effect of NC7H16 addition on the binary mixture, reaction flux, ignition sensitivity, rate of production of the key radicals along with heat production analyses were conducted. Apart from contributing more ȮH production through the low-temperature chain-branching reaction pathways of NC7H16, adding NC7H16 also promotes the pre-ignition heat release of the binary mixture. The heat release raises the system temperature and further promotes the mixture ignition, enhancing the nonlinear effect at low temperatures.
- 7 September 2023
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (10) , 1-31
Spray Ignition and Combustion Modes and Their Time Scales Studies in an Optical Rapid Compression Machine
Spray auto-ignition is a complex physical and chemical process whose mechanism is still not well understood. This paper explores the contribution of physical and chemical mechanisms to spray auto-ignition and combustion behaviors over a wide range of ambient temperature and pressure conditions in an optical rapid compression machine. Specifically, the spray development and ignition process are first visualized and the spray ignition delay times (IDTI) are measured through high-speed imaging. IDTI is then compared with gas phase chemical ignition delay times (IDTC) calculated by 0D homogeneous reactor simulation. Subsequently, different combustion modes are recognized by analyzing the mixture status at the instant of ignition, the spray flame behavior, and the pressure evolution history. Finally, a regime diagram of combustion modes is proposed to illustrate the dominant mechanisms for different spray combustion modes. Results show that the measured spray IDTI is longer than the 0D calculated IDTC due to the physical delay caused by spray development, evaporation, and mixing. At higher temperatures and pressures, the difference between IDTI and IDTC is increased because the evaporation and mixing become progressively important, compared to the chemical reaction mechanism. Scrutinization on the pressure and the apparent heat release rate evolution curve reveals that with the increase of the temperature and pressure, the chemical-controlled combustion time accounts for less and less of the total combustion duration. This further indicates that spray ignition and combustion behaviors transit from chemical-dominated mode to mixing-dominated mode.
- 7 September 2023
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 145 (10) , 1-31
Spray Ignition and Combustion Modes and Their Time Scales Studies in an Optical Rapid Compression Machine
Spray auto-ignition is a complex physical and chemical process whose mechanism is still not well understood. This paper explores the contribution of physical and chemical mechanisms to spray auto-ignition and combustion behaviors over a wide range of ambient temperature and pressure conditions in an optical rapid compression machine. Specifically, the spray development and ignition process are first visualized and the spray ignition delay times (IDTI) are measured through high-speed imaging. IDTI is then compared with gas phase chemical ignition delay times (IDTC) calculated by 0D homogeneous reactor simulation. Subsequently, different combustion modes are recognized by analyzing the mixture status at the instant of ignition, the spray flame behavior, and the pressure evolution history. Finally, a regime diagram of combustion modes is proposed to illustrate the dominant mechanisms for different spray combustion modes. Results show that the measured spray IDTI is longer than the 0D calculated IDTC due to the physical delay caused by spray development, evaporation, and mixing. At higher temperatures and pressures, the difference between IDTI and IDTC is increased because the evaporation and mixing become progressively important, compared to the chemical reaction mechanism. Scrutinization on the pressure and the apparent heat release rate evolution curve reveals that with the increase of the temperature and pressure, the chemical-controlled combustion time accounts for less and less of the total combustion duration. This further indicates that spray ignition and combustion behaviors transit from chemical-dominated mode to mixing-dominated mode.
- 23 December 2022
- Published by Elsevier in Combustion and Flame
- Vol. 248
Experimental and kinetic modeling study of tetramethylethylenediamine: A promising green propellant fuel
- 23 December 2022
- Published by Elsevier in Combustion and Flame
- Vol. 248
Experimental and kinetic modeling study of tetramethylethylenediamine: A promising green propellant fuel
- Open Access
Experimental Investigation on Auto-Ignition Characteristics of Kerosene Spray Flames
To facilitate the better use of RP-3 kerosene in compression ignition engines, the auto-ignition behaviors of RP-3 kerosene spray were experimentally investigated in an optical rapid compression machine. Results show that most of the tests have good ignitability and combustion performance. For all the successful ignited cases, the flame kernel was found to be formed before the steep rise of pressure, which explained that image-based ignition delay time is always shorter than the pressure-based ignition delay time. The effects of ambient environment, injection pressure, and injection delay time on the pressure history, ignition intensity, combustion duration, heat release rate, and other parameters were investigated individually. The ambient environment has a strong influence on ignition delay time by accelerating the chemical reactions, whereas the high injection pressure helps the better vaporization of fuel spray. The effect of injection delay time is non-monotonic as the trade-off relation between heat loss and blending of fuel and oxygen. The heat release rate histories under different conditions were compared and analyzed, and the two-stage heat release phenomenon was observed in the negative temperature coefficient region. The ignition intensity region was determined based on the measured ignition delay times of RP-3 kerosene spray, and multiple linear regression correlation was used to study the ignition delay time sensitivity to multi-factors.
Open AccessExperimental Investigation on Auto-Ignition Characteristics of Kerosene Spray Flames
To facilitate the better use of RP-3 kerosene in compression ignition engines, the auto-ignition behaviors of RP-3 kerosene spray were experimentally investigated in an optical rapid compression machine. Results show that most of the tests have good ignitability and combustion performance. For all the successful ignited cases, the flame kernel was found to be formed before the steep rise of pressure, which explained that image-based ignition delay time is always shorter than the pressure-based ignition delay time. The effects of ambient environment, injection pressure, and injection delay time on the pressure history, ignition intensity, combustion duration, heat release rate, and other parameters were investigated individually. The ambient environment has a strong influence on ignition delay time by accelerating the chemical reactions, whereas the high injection pressure helps the better vaporization of fuel spray. The effect of injection delay time is non-monotonic as the trade-off relation between heat loss and blending of fuel and oxygen. The heat release rate histories under different conditions were compared and analyzed, and the two-stage heat release phenomenon was observed in the negative temperature coefficient region. The ignition intensity region was determined based on the measured ignition delay times of RP-3 kerosene spray, and multiple linear regression correlation was used to study the ignition delay time sensitivity to multi-factors.