Tommaso Grossi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Tommaso Grossi has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
- Ciro Santus
Department of Civil and Industrial Engineering—DICI, University of Pisa, Largo Lucio Lazzarino 1, 56122 Pisa, Italy
9 shared publications - Bernardo Disma Monelli
Department of Civil and Industrial Engineering, University of Pisa, Largo Lucio Lazzarino 1, 56122 Pisa, Italy
5 shared publications - Alessandro Guazzini
Department of Civil and Industrial Engineering, University of Pisa, Largo Lucio Lazzarino 1, 56122 Pisa, Italy
4 shared publications - Lorenzo Romanelli
Department of Civil and Industrial Engineering—DICI, University of Pisa, Largo Lucio Lazzarino 1, 56122 Pisa, Italy
4 shared publications - Federico Bucciarelli
Baker Hughes Nuovo Pignone s.r.l, Via Felice Matteucci 2, 50127 Florence, Italy
3 shared publications M. Beghini
Dipartimento di Ingegneria Civile e Industriale, Università di Pisa, Pisa, Italy
3 shared publications
Latest Publications
- Open Access
Rapid Evaluation of Chaboche–Voce Material Model Parameters Through a Fully Reversed Strain-Controlled Test
Modeling cyclic plasticity remains challenging due to the high computational cost of nonlinear constitutive models and the large number of parameters requiring evaluation, which are often temperature-dependent. This work presents a systematic procedure for identifying the parameters of the Chaboche–Voce model, one of the most widely adopted constitutive models for cyclic plasticity and commonly implemented in finite element software. Due to its nonlinear formulation, however, parameter evaluation is not straightforward. The parameters governing the kinematic hardening response are determined through a simple least-squares fit, yielding an analytical expression for a branch of the mid-life stabilized cycle. The Voce parameters are subsequently obtained by solving an analytical equation followed by a further least-squares fit. The resulting methodology provides a systematic approach for characterizing materials exhibiting both cyclic hardening and softening. The procedure was applied to two materials: 42CrMo4+QT tested at room temperature at different strain ranges for two different values of mean strain and 1Cr-1Mo-0.25V steel tested at different temperatures and strain ranges. The proposed approach provides satisfactory constitutive parameters while requiring virtually negligible computational cost, making it suitable for efficient material characterization and subsequent finite element implementation.
Open AccessRapid Evaluation of Chaboche–Voce Material Model Parameters Through a Fully Reversed Strain-Controlled Test
Modeling cyclic plasticity remains challenging due to the high computational cost of nonlinear constitutive models and the large number of parameters requiring evaluation, which are often temperature-dependent. This work presents a systematic procedure for identifying the parameters of the Chaboche–Voce model, one of the most widely adopted constitutive models for cyclic plasticity and commonly implemented in finite element software. Due to its nonlinear formulation, however, parameter evaluation is not straightforward. The parameters governing the kinematic hardening response are determined through a simple least-squares fit, yielding an analytical expression for a branch of the mid-life stabilized cycle. The Voce parameters are subsequently obtained by solving an analytical equation followed by a further least-squares fit. The resulting methodology provides a systematic approach for characterizing materials exhibiting both cyclic hardening and softening. The procedure was applied to two materials: 42CrMo4+QT tested at room temperature at different strain ranges for two different values of mean strain and 1Cr-1Mo-0.25V steel tested at different temperatures and strain ranges. The proposed approach provides satisfactory constitutive parameters while requiring virtually negligible computational cost, making it suitable for efficient material characterization and subsequent finite element implementation.
- Open Access
- 20 October 2026
- Published by MDPI AG in Preprints.org
Rapid Evaluation of Chaboche–Voce Material Model Parameters Through a Fully Reversed Strain-Controlled Test
Modeling cyclic plasticity remains challenging due to the high computational cost of nonlinear constitutive models and the large number of parameters requiring evaluation, which are often temperature-dependent. This work presents a systematic procedure for identifying the parameters of the Chaboche–Voce model, one of the most widely adopted constitutive models for cyclic plasticity and commonly implemented in finite element software. Due to its nonlinear formulation, however, parameter evaluation is not straightforward. The parameters governing the kinematic hardening response are determined through a simple least-squares fit, yielding an analytical expression for a branch of the mid-life stabilized cycle. The Voce parameters are subsequently obtained by solving an analytical equation followed by a further least-squares fit. The resulting methodology provides a systematic approach for characterizing materials exhibiting both cyclic hardening and softening. The procedure was applied to two materials: 42CrMo4+QT tested at room temperature at different strain ranges for two different values of mean strain and 1Cr-1Mo-0.25V steel tested at different temperatures and strain ranges. The proposed approach provides satisfactory constitutive parameters while requiring virtually negligible computational cost, making it suitable for efficient material characterization and subsequent finite element implementation.
- 20 October 2026
- Published by MDPI AG in Preprints.org
Open AccessRapid Evaluation of Chaboche–Voce Material Model Parameters Through a Fully Reversed Strain-Controlled Test
Modeling cyclic plasticity remains challenging due to the high computational cost of nonlinear constitutive models and the large number of parameters requiring evaluation, which are often temperature-dependent. This work presents a systematic procedure for identifying the parameters of the Chaboche–Voce model, one of the most widely adopted constitutive models for cyclic plasticity and commonly implemented in finite element software. Due to its nonlinear formulation, however, parameter evaluation is not straightforward. The parameters governing the kinematic hardening response are determined through a simple least-squares fit, yielding an analytical expression for a branch of the mid-life stabilized cycle. The Voce parameters are subsequently obtained by solving an analytical equation followed by a further least-squares fit. The resulting methodology provides a systematic approach for characterizing materials exhibiting both cyclic hardening and softening. The procedure was applied to two materials: 42CrMo4+QT tested at room temperature at different strain ranges for two different values of mean strain and 1Cr-1Mo-0.25V steel tested at different temperatures and strain ranges. The proposed approach provides satisfactory constitutive parameters while requiring virtually negligible computational cost, making it suitable for efficient material characterization and subsequent finite element implementation.
- Open Access
- 2 September 2026
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- p. 1-12
Measurement of Non-uniform Residual Stresses Using the Incremental Hole Drilling Method and Digital Image Correlation: A Feasibility Study on Deep Rolled Specimens
This study explores the applicability of digital image correlation (DIC) techniques for measuring non-uniform residual stresses using the incremental hole drilling method. Specifically, it examines the residual stresses induced by a deep rolling treatment on 7075-T6 aluminum specimens, characterized by strong depth gradients. The aim is to assess the potential of replacing traditional strain gauge rosettes with DIC systems. After the deep rolling treatment, residual stresses were measured using the classic hole drilling method with a strain gauge rosette according to ASTM E837, providing a reference for the DIC measurements. The specimens and camera were mounted on a CNC machine, which allowed precise repositioning of both elements at each drilling step. Experimental results show that DIC measurements allow for the calculation of residual stresses with good accuracy. While their precision is lower than traditional strain gauge measurements, full-field DIC techniques partially compensate for this disadvantage by measuring the entire deformation field around the hole. This approach offers statistically advantageous data redundancy and captures displacements in areas immediately surrounding the hole, which are more sensitive to residual stresses. Considering the time and cost savings by avoiding the use of strain gauge rosettes, DIC techniques offer a valid alternative for determining residual stresses with the hole drilling method. The key factor for their application lies in the ease of repositioning both the camera and the drill at each depth increment.
- 2 September 2026
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- p. 1-12
Open AccessMeasurement of Non-uniform Residual Stresses Using the Incremental Hole Drilling Method and Digital Image Correlation: A Feasibility Study on Deep Rolled Specimens
This study explores the applicability of digital image correlation (DIC) techniques for measuring non-uniform residual stresses using the incremental hole drilling method. Specifically, it examines the residual stresses induced by a deep rolling treatment on 7075-T6 aluminum specimens, characterized by strong depth gradients. The aim is to assess the potential of replacing traditional strain gauge rosettes with DIC systems. After the deep rolling treatment, residual stresses were measured using the classic hole drilling method with a strain gauge rosette according to ASTM E837, providing a reference for the DIC measurements. The specimens and camera were mounted on a CNC machine, which allowed precise repositioning of both elements at each drilling step. Experimental results show that DIC measurements allow for the calculation of residual stresses with good accuracy. While their precision is lower than traditional strain gauge measurements, full-field DIC techniques partially compensate for this disadvantage by measuring the entire deformation field around the hole. This approach offers statistically advantageous data redundancy and captures displacements in areas immediately surrounding the hole, which are more sensitive to residual stresses. Considering the time and cost savings by avoiding the use of strain gauge rosettes, DIC techniques offer a valid alternative for determining residual stresses with the hole drilling method. The key factor for their application lies in the ease of repositioning both the camera and the drill at each depth increment.
- Open Access
- 27 August 2026
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- p. 1-18
Ill-Posedness, Bias, and the Case for Average Stresses in Residual Stress Evaluations
The evaluation of residual stresses using relaxation methods is a central problem in experimental mechanics, yet the conventional pursuit of pointwise stress values creates persistent physical and mathematical difficulties. Physically, the isotropic continuum models underlying these methods lose validity near the microstructural grain scale, rendering highly localized stress values physically dubious. Mathematically, deriving these pointwise values from measured relaxed strains constitutes an ill-posed inverse problem. To achieve a manageable signal-to-noise ratio, established inversion methods—such as the Integral Method or Tikhonov regularization—must enforce a bias–variance trade-off. This introduces an inherently unquantifiable bias, severely compromising the reliability of standard uncertainty quantification. To resolve this misalignment between physical reality and mathematical formulation, this paper advocates a fundamental shift: Redefining the measurement target from pointwise extremes to the spatial average of the residual stress field over a physically significant characteristic length ( $$l_\sigma $$ ). Because engineering failure criteria (such as fatigue and fracture) are driven by stress integrals over specific volumes rather than single points, this redefinition is physically natural. Most importantly, it makes the inverse problem mathematically well-posed: the bias–variance trade-off vanishes, and standard uncertainty propagation yields exact, highly reliable confidence intervals. Building on recent theoretical frameworks [1], this work develops the physical justification for this scale-dependent reformulation. It provides a critical review of the systematic biases embedded in classical inversion techniques and presents a comprehensive numerical simulation of a hole-drilling residual stress measurement on a shot-peened steel component. This simulation explicitly shows how the spatial averaging procedure guarantees nominal confidence interval coverage, contrasting with the hidden biases of established approaches.- 27 August 2026
- Published by Springer Nature in Journal of Failure Analysis and Prevention
- p. 1-18
Open AccessIll-Posedness, Bias, and the Case for Average Stresses in Residual Stress Evaluations
The evaluation of residual stresses using relaxation methods is a central problem in experimental mechanics, yet the conventional pursuit of pointwise stress values creates persistent physical and mathematical difficulties. Physically, the isotropic continuum models underlying these methods lose validity near the microstructural grain scale, rendering highly localized stress values physically dubious. Mathematically, deriving these pointwise values from measured relaxed strains constitutes an ill-posed inverse problem. To achieve a manageable signal-to-noise ratio, established inversion methods—such as the Integral Method or Tikhonov regularization—must enforce a bias–variance trade-off. This introduces an inherently unquantifiable bias, severely compromising the reliability of standard uncertainty quantification. To resolve this misalignment between physical reality and mathematical formulation, this paper advocates a fundamental shift: Redefining the measurement target from pointwise extremes to the spatial average of the residual stress field over a physically significant characteristic length ( $$l_\sigma $$ ). Because engineering failure criteria (such as fatigue and fracture) are driven by stress integrals over specific volumes rather than single points, this redefinition is physically natural. Most importantly, it makes the inverse problem mathematically well-posed: the bias–variance trade-off vanishes, and standard uncertainty propagation yields exact, highly reliable confidence intervals. Building on recent theoretical frameworks [1], this work develops the physical justification for this scale-dependent reformulation. It provides a critical review of the systematic biases embedded in classical inversion techniques and presents a comprehensive numerical simulation of a hole-drilling residual stress measurement on a shot-peened steel component. This simulation explicitly shows how the spatial averaging procedure guarantees nominal confidence interval coverage, contrasting with the hidden biases of established approaches. - Open Access
- 10 August 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 265
Hydrogen permeation and trapping in iron at sub-atmospheric partial pressures using a gas/electrochemical Devanathan–Stachurski cell
- 10 August 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 265
Open AccessHydrogen permeation and trapping in iron at sub-atmospheric partial pressures using a gas/electrochemical Devanathan–Stachurski cell
- Open Access
- 10 June 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 248
A Multi-task Bayesian Optimization framework to identify a Gurson–Tvergaard–Needleman constitutive model for an MS1500 steel in hydrogen environment
- 10 June 2026
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 248
Open AccessA Multi-task Bayesian Optimization framework to identify a Gurson–Tvergaard–Needleman constitutive model for an MS1500 steel in hydrogen environment
- Open Access
- 6 March 2026
- Published by EDP Sciences in Matériaux & Techniques
- Vol. 114 (1) , 104
Improving sustainability of cold rolling of low-carbon steels via oil free lubricants
The European steel sector is committed to improve sustainability of the whole steel production chain, from decarbonisation of major upstream processes up to all downstream operations, including rolling. In particular, in the cold rolling process, oil-in-water emulsions are usually applied to lubricate the cold rolling process of low-Carbon steel. Such emulsions present some drawbacks mainly related to emulsion bath maintenance, subsequent production stages and waste disposal. Past research works showed that in some application areas, Oil Free Lubricants (OFL) show lubricant properties that are comparable to conventional lubricants, while providing significant environmental benefits. These lubricants are formulated as aqueous dispersions of Polyalkylene Glycols (PAG), a water-soluble synthetic polymer base, combined with various additives for lubrication enhancement, corrosion protection, and oil rejection. The project entitled “Transfer of aqueous oil free lubricants into steel cold rolling practice” (Ref. RollOilFree II – G.A. No 101112433) aims at developing an Oil-Free Lubricant for the cold rolling process of low-Carbon steel for applications in the automotive and packaging sectors by assessing its performance in industrial conditions. To this aim, the project combines tests at laboratory scale and simulations with trials in an industrial pilot cold rolling mill and, finally, field trials at industrial scale. Results demonstrate that OFL01 and OFL02 represent the most promising formulations as substitutes for commercial lubricants. The paper overviews the work undertaken in the first 18 months of the project, including laboratory investigations and part of the pilot trials.
- 6 March 2026
- Published by EDP Sciences in Matériaux & Techniques
- Vol. 114 (1) , 104
Open AccessImproving sustainability of cold rolling of low-carbon steels via oil free lubricants
The European steel sector is committed to improve sustainability of the whole steel production chain, from decarbonisation of major upstream processes up to all downstream operations, including rolling. In particular, in the cold rolling process, oil-in-water emulsions are usually applied to lubricate the cold rolling process of low-Carbon steel. Such emulsions present some drawbacks mainly related to emulsion bath maintenance, subsequent production stages and waste disposal. Past research works showed that in some application areas, Oil Free Lubricants (OFL) show lubricant properties that are comparable to conventional lubricants, while providing significant environmental benefits. These lubricants are formulated as aqueous dispersions of Polyalkylene Glycols (PAG), a water-soluble synthetic polymer base, combined with various additives for lubrication enhancement, corrosion protection, and oil rejection. The project entitled “Transfer of aqueous oil free lubricants into steel cold rolling practice” (Ref. RollOilFree II – G.A. No 101112433) aims at developing an Oil-Free Lubricant for the cold rolling process of low-Carbon steel for applications in the automotive and packaging sectors by assessing its performance in industrial conditions. To this aim, the project combines tests at laboratory scale and simulations with trials in an industrial pilot cold rolling mill and, finally, field trials at industrial scale. Results demonstrate that OFL01 and OFL02 represent the most promising formulations as substitutes for commercial lubricants. The paper overviews the work undertaken in the first 18 months of the project, including laboratory investigations and part of the pilot trials.
- Open Access
- 13 December 2025
- Published by Springer Nature in Communications Engineering
- Vol. 4 (1)
NeuberNet: a neural operator solving elastic-plastic partial differential equations at V-notches from low-fidelity elastic simulations
Stress concentrations at geometric irregularities such as reentrant corners make it challenging to efficiently simulate localized plastic deformation in engineering materials. Fully nonlinear models capture these effects accurately but are computationally costly, whereas simplified elastic analyses neglect important nonlinearities. Here, we present NeuberNet, a Multi-Task Nonlinear Manifold Decoder that learns mappings between far-field displacement boundary conditions from low-fidelity elastic simulations and the corresponding high-resolution stress and strain fields derived from elastic-plastic axisymmetric solid mechanics, under assumptions of small-scale plasticity and bilinear isotropic hardening. NeuberNet serves as a data-driven implementation of the substructuring principle, designed to model complex geometries by activating plastic behavior only near stress raisers where nonlinearities arise. We provide guidelines for mesh resolution in low-fidelity simulations, demonstrate NeuberNet’s ability to identify violations of the small-scale plasticity assumption, and assess its robustness to nonlinear hardening laws. We also show that NeuberNet generalizes to 3D problems with axisymmetric geometries and non-symmetric boundary conditions. Overall, NeuberNet provides a reliable and computationally efficient framework for small-scale plasticity analysis.
- 13 December 2025
- Published by Springer Nature in Communications Engineering
- Vol. 4 (1)
Open AccessNeuberNet: a neural operator solving elastic-plastic partial differential equations at V-notches from low-fidelity elastic simulations
Stress concentrations at geometric irregularities such as reentrant corners make it challenging to efficiently simulate localized plastic deformation in engineering materials. Fully nonlinear models capture these effects accurately but are computationally costly, whereas simplified elastic analyses neglect important nonlinearities. Here, we present NeuberNet, a Multi-Task Nonlinear Manifold Decoder that learns mappings between far-field displacement boundary conditions from low-fidelity elastic simulations and the corresponding high-resolution stress and strain fields derived from elastic-plastic axisymmetric solid mechanics, under assumptions of small-scale plasticity and bilinear isotropic hardening. NeuberNet serves as a data-driven implementation of the substructuring principle, designed to model complex geometries by activating plastic behavior only near stress raisers where nonlinearities arise. We provide guidelines for mesh resolution in low-fidelity simulations, demonstrate NeuberNet’s ability to identify violations of the small-scale plasticity assumption, and assess its robustness to nonlinear hardening laws. We also show that NeuberNet generalizes to 3D problems with axisymmetric geometries and non-symmetric boundary conditions. Overall, NeuberNet provides a reliable and computationally efficient framework for small-scale plasticity analysis.
- Open Access
- 16 October 2025
- Published by Elsevier in Measurement
- Vol. 258
Improved residual stress evaluation with Hole-Drilling and DIC through the L-curve tool and super-resolution along depth
- 16 October 2025
- Published by Elsevier in Measurement
- Vol. 258
Open AccessImproved residual stress evaluation with Hole-Drilling and DIC through the L-curve tool and super-resolution along depth
- Open Access
Constitutive Modeling of Creep–Fatigue Interaction in 1Cr-1Mo-0.25V Steel for Hold-Time Testing
In the field of energy production, creep–fatigue interaction is a typical failure mode that might compromise the structural integrity of both rotating equipment and pressure vessels. Common design practices approach the problem in a conservative way by using high safety factors, which typically results in additional costs for manufacturing companies. The aim of this article, in the framework of continuum damage mechanics approaches, is to present a novel fatigue damage-based constitutive law. The presented law is directly inspired by well-assessed creep-based rules, suggesting a similarity in the behavior. On the other hand, creep deformation and damage are calculated with a more recent approach. The identification of the model parameters was carried out by interpreting experimental results obtained from low-cycle fatigue and creep relaxation tests performed on a commonly used ferritic–martensitic steel for power generation rotor forgings. To validate the proposed models, they were used to estimate material life consumption when the material was subjected to fully reversed axial loading conditions with hold time under tensile load. Different loading conditions at different total strain ranges and hold times were simulated, and good agreement was found between the predicted and experimental life, thus confirming the validity of the proposed models.
Open AccessConstitutive Modeling of Creep–Fatigue Interaction in 1Cr-1Mo-0.25V Steel for Hold-Time Testing
In the field of energy production, creep–fatigue interaction is a typical failure mode that might compromise the structural integrity of both rotating equipment and pressure vessels. Common design practices approach the problem in a conservative way by using high safety factors, which typically results in additional costs for manufacturing companies. The aim of this article, in the framework of continuum damage mechanics approaches, is to present a novel fatigue damage-based constitutive law. The presented law is directly inspired by well-assessed creep-based rules, suggesting a similarity in the behavior. On the other hand, creep deformation and damage are calculated with a more recent approach. The identification of the model parameters was carried out by interpreting experimental results obtained from low-cycle fatigue and creep relaxation tests performed on a commonly used ferritic–martensitic steel for power generation rotor forgings. To validate the proposed models, they were used to estimate material life consumption when the material was subjected to fully reversed axial loading conditions with hold time under tensile load. Different loading conditions at different total strain ranges and hold times were simulated, and good agreement was found between the predicted and experimental life, thus confirming the validity of the proposed models.