Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Fildah Ayaa has a total of 12 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Synthesis of Carboxylic Cellulose Nanocrystals From Yellow Thatching Grass ( Hyparrhenia filipendula) via Citric Acid Hydrolysis

    by Fildah Ayaa, Michael Lubwama, Samuel Ayodele Iwarere, Michael Olawale Daramola, John Baptist Kirabira

    Grass is an abundant and renewable source of cellulose, which makes it a sustainable and cost‐effective source for producing cellulose nanocrystals. Moreover, the extraction of cellulose nanocrystals from grass provides a value‐added product from an otherwise low‐value agricultural waste material, which can contribute to the development of a circular economy. In this study, cellulose nanocrystals (CNCs) were extracted from Hyparrhenia filipendula via citric acid hydrolysis. The Hyparrhenia filipendula stems were pre‐processed through mechanical size reduction and Soxhlet extraction. The extractive‐free stems were fractionated using two solvents: 10 wt% (w/v) sodium hydroxide (NaOH) and deep eutectic solvent of ethylene glycol:citric acid (1:2 molar ratio). The fractionated samples were bleached with acidified sodium chlorite and hydrolyzed with 80 wt% citric acid for 4 h at 120°C in a Parr reactor. The samples obtained at each treatment stage were characterized using standard scientific procedures for chemical composition, morphology, elemental composition, crystallinity, and thermal stability. The results show that CNCs were successfully extracted from Hyparrhenia filipendula via citric acid hydrolysis. The surface morphology of alkali fractionated CNCs was needle‐like, whereas the surface morphology of DES fractionated CNCs was rod‐like. The alkali fractionated and hydrolyzed sample, NaCNC, had the highest cellulose purity (91%), as well as the highest thermal stability. The FTIR analysis proved the removal of non‐cellulosic components in the CNCs, except for the unbleached CNCs that had significant quantities of hemicellulose and lignin. The XRD analysis revealed the presence of characteristic cellulose Iβ in the CNCs, with the UNNaCNC sample (NaOH fractionated, unbleached, acid hydrolyzed sample) having the highest crystallinity index of 81% and the largest crystallite size of 4.20 nm. The properties of the CNCs obtained in this study are comparable to CNCs derived from previously reported lignocellulosic materials. The CNCs from Hyparrhenia filipendula therefore have a wide range of potential applications.


  • Open Access

    Production and Characterization of Densified Briquettes From Nanocomposite Biochar-Cellulose Nanocrystal (Biochar-CNC) Reinforced with Polyvinyl Alcohol (PVA)

    by Fildah Ayaa, Kabir Oyedotun, Michael Lubwama, Samuel Ayodele Iwarere, Michael Olawale Daramola, John Baptist Kirabira

    Biomass briquettes are still important to communities in developing nations because they are cheap, sustainable, and generated from solid waste that can be utilized to produce energy. However, the low quality of the briquettes when compared to traditional cooking fuels hampers their widespread adoption; yet, there is an opportunity for expanding the briquette market due to the rise in charcoal prices, increasing scarcity of forest resources, and more environmental awareness among consumers. The main objective of this study was to develop a bio-based briquette with improved combustion characteristics through the use of an innovative binder. A novel nanocomposite briquette (biochar/cellulose nanocrystals (CNC)/polyvinyl alcohol (PVA) was produced using the solution casting method, with CNC/PVA nanocomposite as a binder. A total of five (5) nanocomposite briquettes having biochar-to-binder ratios of; 90:10, 80:20, 70:30, 60:40, and 50:50 and designated as BCP (9/1), BCP (8/2), BCP (7/3), BCP (6/4) and BCP (5/5), respectively were developed. The nanocomposite briquette samples were characterized for thermal stability, mechanical properties, elemental composition, surface morphology, proximate composition, and combustion characteristics using established methods. The produced briquettes had a very low ash content of less than 2% and a low average moisture content of 8%. The surface morphology of the briquettes revealed a rough and porous structure that can enhance combustion. The BCP (9/1) briquette had the highest calorific value of 27 MJ/kg, followed by BCP (8/2) and BCP (7/3) which had a calorific value of 26 MJ/kg. The BCP (7/3) nanocomposite briquette was the most thermally stable, with the lowest onset degradation temperature (220 °C), highest peak temperature (514 °C), least char residue, and the most compressive strength of 11 MPa. The BCP (9/1), BCP (8/2), and BCP (7/3) nanocomposite briquettes also satisfied the combustion indices criteria, demonstrating their potential to replace coal in industrial applications. The thermal degradation and kinetics of the nanocomposites were studied using TGA-DTG techniques at three different heating rates; 5 °C/min, 10 °C/min, 20 °C/min in an oxygen environment. The kinetic parameters, that is, the activation energy and pre-exponential factor were calculated using the Coats-Redfern method. The combustion of the briquettes happened in three distinct phases with a higher activation energy required at higher heating rates to initiate the first stage of combustion. Also, up to 40% of the binder can be added without affecting the ignition, combustion, and burn-out properties of the briquette. This study, therefore, demonstrates that Biochar-PVA-CNC nanocomposite briquettes are a potential biofuel for industrial and household applications.


  • Potential of invasive shrubs for energy applications in Uganda

    by Fildah Ayaa, Michael Lubwama, John Baptist Kirabira, Xi Jiang


  • Open Access

    Extraction and characterization of cellulose nanofibers from yellow thatching grass (Hyparrhenia filipendula) straws via acid hydrolysis

    by N Ndwandwa, F Ayaa, S Iwarere, Michael Daramola, Jb Kirabira

    Purpose: A variety of lignocellulosic raw materials have been previously reported for the production of cellulose and cellulose derivatives, but little research effort has been dedicated to producing cellulose from Hyparrhenia filipendula . In this study, cellulose nanofibers (CNFs) were extracted from Hyparrhenia filipendula waste straws via sulphuric acid hydrolysis. Methods: The straws were pretreated with a combination of physiochemical processes and hydrolyzed using sulphuric acid at three different concentrations (1 M, 3 M and 5.6 M) for 2 hours at 80 °C. The properties of the CNFs was checked by Fourier Transform Infrared spectroscopy (FTIR) for surface chemistry, X-ray diffraction (XRD) for crystallinity, Scanning Electron microscopy and Transmission electron microscopy (TEM) for morphology. A high-performance liquid chromatograph (HPLC) was used to quantify the amount of biopolymers in the CNFs. Results: The results show that CNFs, denoted as CNF 1 , CNF 3 , and CNF 5.6 for 1 M, 3 M, and 5.6 M sulphuric acid, respectively, were successfully extracted at the various concentrations of sulphuric acid. The cellulose content of CNF1 , CNF3 , and CNF5.6 determined by HPLC analysis were 85%, 77 % and 78 % respectively. Also, the hemicellulose content in CNF 1 , CNF 3 , and CNF 5.6 was 10 %, 15 %, and 12 % respectively, showing a high carbohydrate content of the CNFs. The FTIR spectra confirm the absence of characteristic peaks for lignin in the CNFs. The XRD analysis reveals presence of characteristic cellulose I β peaks at 2θ of 18°, 26°, and 40° with the crystallinity of 78%, 74 % and 73% for CNF1, CNF3 and CNF5.6, respectively. Moreover, SEM analysis shows the deposition of lignin polycondensate on the surface of CNF 1 , CNF 3 , and CNF 5.6 while the bleached sample has a smooth and glossy appearance. The TEM analysis shows long unbranched nano-sized fibers for CNF 1 and shorter fibrous network of fibers for CNF 3 , and CNF 5.6. The average diameter of the fibers, measured with ImageJ software is 40 nm for CNF 1 , 57 nm for CNF 3 , and 92 nm for CNF 5.6. Conclusion: CNFs were successfully produced from Hyparrhenia filipendula and reported for the first time in open literature. In view of the structure and properties of the produced CNFs, they are a potential material for value-added applications such as polymer matrices, films, and membranes, thus enabling efficient utilization of agricultural waste.


  • Open Access

    Fractionation of yellow thatching grass (Hyparrhenia filipendula) for sugar production using combined Alkaline and Deep eutectic solvent pretreatment

    by F Masuku, F. Ayaa, C.M. Onyelucheya, S.A. Iwarere, Michael Daramola, John Kirabira

    Purpose Biomass pretreatment followed by enzymatic hydrolysis is one of the most viable ways to obtain sugars from biomass. In this work, the effect combined alkaline pretreatment and Deep Eutectic Solvent (DES) on enzyme hydrolysis of Hyparrhenia filipendula by cellulase is investigated. There is no previously reported literature on this substrate and the authors aim to establish baseline values for further research in the utilization of Hyparrhenia filipendula. Methods The yellow thatching grass (Hyparrhenia filipendula) was fractionated with a combination of alkaline and Deep Eutectic Solvent (DES) to increase sugar recovery. An alkaline solution of 10 wt % (w/v) of Sodium Hydroxide (NaOH) was used for the first stage of pretreatment at 100 °C for 4 h. Three DES, namely, Choline chloride (ChCl): urea; ChCl: glycerol; and Ethylene glycol: Citric acid at 1:2 molar ratio each, were heated to 80 °C until a clear solution was formed. The DESs were used for the second stage of pretreatment at 110 °C for 6 h in a Parr reactor. During the pretreatment, a solid: solvent ratio of 1:10 was used for the first and second stages of pre-treatment. Enzymatic hydrolysis was accomplished with a cellulase enzyme blend, Cellic CTec2, in a 50 mM sodium citrate buffer (pH 4.8) at 50 °C using a shaking incubator at a speed of 150 rpm. A solid loading of 2 % and enzyme dosage of 50 g/100 g cellulose in the sample was used for all the experiments. Furthermore, samples were withdrawn every 24 hours for 7 days and analyzed for glucose and xylose using High-Performance Liquid Chromatography (HPLC). Results A high delignification of 90 % and hemicellulose removal of 70 % was achieved with a combination of Alkali and ChCl: Urea pretreatment. Subsequently, the highest glucose and xylose conversion of 90 % and 92 % were observed, respectively, with the same sample. Additionally, the highest glucose yield achieved was 25 gL-1 from the combined alkaline/ChCl: Glycerol treated sample after 120 h. Moreover, the highest xylose yield was 3 gL-1 from the raw sample, the NaOH- pulped sample, and the ChCl: Glycerol-treated sample. Conclusion The results from this study demonstrated that the solvents used for fractionating biomass have a significant effect on the sugar recovery during enzymatic hydrolysis. Also, the pretreatment with a combination of NaOH and DES of ChCl: Glycerol was the most effective for the recovery of glucose and total sugar. In conclusion, yellow thatching grass is a promising substrate for bio-refineries. However, the ideal conditions for enzyme hydrolysis should be investigated further to promote its utilization for value-added products.