GMGeorgiana Mladin

Georgiana Mladin

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Georgiana Mladin has a total of 6 co-authors. Here are the top co-authors by number of shared publications:

  • Adina Negrea

    Department of Applied Chemistry and Environmental Engineering and Inorganic Compounds, Faculty of Industrial Chemistry, Biotechnology and Environmental Engineering, Politehnica University Timisoara, Vasile Parvan 6, 300223 Timisoara, Romania

    1 shared publication
  • Catalin Ianasi

    “Coriolan Dragulescu” Institute of Chemistry, Romanian Academy, Mihai Viteazu No. 24, 300223 Timișoara, Romania

    1 shared publication
  • Mihaela Ciopec

    Faculty of Chemical Engineering, Biotechnologies and Environmental Protection, Politehnica University Timisoara, Victoriei Square, No. 2, 300006 Timisoara, Romania

    1 shared publication
  • Narcis Duteanu

    Faculty of Industrial Chemistry and Environmental Engineering, Politehnica University of Timisoara, 2 Square Victoriei, 300006 Timisoara, Romania

    1 shared publication
  • Paula Svera

    National Institute for Research and Development in Electrochemistry and Condensed Matter, 144th Dr. A.P. Podeanu Street, 300569 Timisoara, Romania

    1 shared publication
  • Petru Negrea

    Faculty of Chemical Engineering, Biotechnologies and Environmental Protection, Politehnica University Timisoara, Victoriei Square, No. 2, 300006 Timisoara, Romania

    1 shared publication

Latest Publications

  • Open Access

    Silica- Iron Oxide Nanocomposite Enhanced with Porogen Agent Used for Arsenic Removal

    by Georgiana Mladin, Mihaela Ciopec, Adina Negrea, Narcis Duteanu, Petru Negrea, Paula Ianasi, Cătălin Ianași

    This study aims to remove arsenic from an aqueous medium by adsorption on a nanocomposite material obtained by the sol–gel method starting from matrices of silica, iron oxide and NaF (SiO2/Fe(acac)3/NaF). Initially, the study focused on the synthesis and characterization of the material by physico–chemical methods such as: X-ray diffraction, FT-IR spectroscopy, Raman spectroscopy, atomic force microscopy, and magnetization. Textural properties were obtained using nitrogen adsorption/desorption measurements. The zero load point, pHpZc, was also determined by the method of bringing the studied system into equilibrium. In addition, this study also provides a comprehensive discussion of the mechanism of arsenic adsorption by conducting kinetic, thermodynamic and equilibrium studies. Studies have been performed to determine the effects of adsorbent dose, pH and initial concentration of arsenic solution, material/arsenic contact time and temperature on adsorption capacity and material efficiency. Three theoretical adsorption isotherms were used, namely Langmuir, Freundlich and Sips, to describe the experimental results. The Sips isotherm was found to best describe the experimental data obtained, the maximum adsorption capacity being ~575 µg As(III)/g. The adsorption process was best described by pseudo-second order kinetics. Studies have been performed at different pH values to establish not only the optimal pH at which the adsorption capacity is maximum, but also which is the predominantly adsorbed species. The effect of pH and desorption studies have shown that ion exchange and the physiosorption mechanism are implicated in the adsorption process. From a thermodynamic point of view, parameters such as ΔG°, ΔH° and ΔS° were evaluated to establish the mechanism of the adsorption process. Desorption studies have been performed to determine the efficiency of the material and it has been shown that the material can be used successfully to treat a real-world example of deep water with a high arsenic content.