Aum Sagar Panda
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Aum Sagar Panda has a total of 23 co-authors. Here are the top co-authors by number of shared publications:
- Rong-Ming Ho
Department of Chemical Engineering, National Tsing Hua University, Hsinchu, Taiwan
5 shared publications - Apostolos Avgeropoulos
Department of Materials Science Engineering, University of Ioannina, Dourouti, 45110 Ioannina, Greece
3 shared publications Fu-Rong Chen
Department of Engineering and System Science
3 shared publicationsThanmayee Shastry
Department of Chemical Engineering
3 shared publicationsYi-Chien Lee
Department of Chemical Engineering, National Tsing Hua University, Hsinchu 30013, Taiwan
3 shared publicationsChen-Jung Hung
Department of Chemical Engineering, National Tsing Hua University, Hsinchu 30013, Taiwan
2 shared publications
Latest Publications
- Open Access
- 29 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (40) , 56542-56552
Stress-Induced Directed Self-Assembly of Perpendicularly Oriented Block Copolymer Lamellae for Lithographic Density Multiplication
This work demonstrates a stress-induced directed self-assembly (DSA) approach to produce unidirectionally oriented perpendicular lamellae in block copolymer (BCP) thin films, achieving a smaller line width and a higher aspect-ratio for pattern transfer with lithographic density multiplication. A free-standing polystyrene-block-polydimethylsiloxane (PS-b-PDMS) thin film on a transmission electron microscopy (TEM) grid is thermally annealed under high vacuum inside an in situ, temperature-resolved TEM instrument. The high vacuum reduces the surface tension discrepancy between PS and PDMS at high temperatures, creating neutral surfaces at both top and bottom sides of the thin film and facilitating the formation of film-spanning perpendicular lamellae via self-alignment during thermal annealing. Finite element analysis reveals that the x-directional stress is concentrated at the grid edge, inducing the formation of unidirectionally oriented perpendicular lamellae, as evidenced by an in situ, time-resolved TEM observation. This edge-parallel alignment arises from a tensile stress gradient along the edge-normal direction, which favors lamellae aligned parallel to the edge to minimize elastic mismatch between PS and PDMS during self-assembly. For nanopatterning, the free-standing thin film is transferred onto substrates with e-beam-defined trenches followed by thermal annealing in a homemade vacuum oven. The BCP film gradually flows into the trenches during which the stress guides the formation of unidirectionally oriented perpendicular lamellae. Subsequently, well-defined SiO2 line patterns can be formed within the trenches after O2 reactive ion etching. This facile method enables controlled orientation of a free-standing BCP thin film by integrating vacuum-driven perpendicular orientation and stress-induced DSA, providing appealing potential for fabrication of highly ordered line patterns in advanced lithographic applications.
- 29 September 2025
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 17 (40) , 56542-56552
Open AccessStress-Induced Directed Self-Assembly of Perpendicularly Oriented Block Copolymer Lamellae for Lithographic Density Multiplication
This work demonstrates a stress-induced directed self-assembly (DSA) approach to produce unidirectionally oriented perpendicular lamellae in block copolymer (BCP) thin films, achieving a smaller line width and a higher aspect-ratio for pattern transfer with lithographic density multiplication. A free-standing polystyrene-block-polydimethylsiloxane (PS-b-PDMS) thin film on a transmission electron microscopy (TEM) grid is thermally annealed under high vacuum inside an in situ, temperature-resolved TEM instrument. The high vacuum reduces the surface tension discrepancy between PS and PDMS at high temperatures, creating neutral surfaces at both top and bottom sides of the thin film and facilitating the formation of film-spanning perpendicular lamellae via self-alignment during thermal annealing. Finite element analysis reveals that the x-directional stress is concentrated at the grid edge, inducing the formation of unidirectionally oriented perpendicular lamellae, as evidenced by an in situ, time-resolved TEM observation. This edge-parallel alignment arises from a tensile stress gradient along the edge-normal direction, which favors lamellae aligned parallel to the edge to minimize elastic mismatch between PS and PDMS during self-assembly. For nanopatterning, the free-standing thin film is transferred onto substrates with e-beam-defined trenches followed by thermal annealing in a homemade vacuum oven. The BCP film gradually flows into the trenches during which the stress guides the formation of unidirectionally oriented perpendicular lamellae. Subsequently, well-defined SiO2 line patterns can be formed within the trenches after O2 reactive ion etching. This facile method enables controlled orientation of a free-standing BCP thin film by integrating vacuum-driven perpendicular orientation and stress-induced DSA, providing appealing potential for fabrication of highly ordered line patterns in advanced lithographic applications.
- Open Access
- 22 July 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (30) , 40263-40274
Sequential Self-Assembly of Polystyrene-block-Polydimethylsiloxane for 3D Nanopatterning via Solvent Annealing
This study aims to develop a strategy for the fabrication of multilayer nanopatterns through sequential self-assembly of lamella-forming polystyrene-block-polydimethylsiloxane (PS-b-PDMS) block copolymer (BCP) from solvent annealing. By simply tuning the solvent selectivity, a variety of self-assembled BCP thin-film morphologies, including hexagonal perforated lamellae (HPL), parallel cylinders, and spheres, can be obtained from single-composition PS-b-PDMS. By taking advantage of reactive ion etching (RIE), topographic SiO2 monoliths with well-ordered arrays of hexagonally packed holes, parallel lines, and hexagonally packed dots can be formed. Subsequently, hole-on-dot and line-on-hole hierarchical textures can be created through a layer-by-layer process with RIE treatment as evidenced experimentally and confirmed theoretically. The results demonstrated the feasibility of creating three-dimensional (3D) nanopatterning from the sequential self-assembly of single-composition PS-b-PDMS via solvent annealing, providing an appealing process for nano-MEMS manufacturing based on BCP lithography.
- 22 July 2024
- Published by American Chemical Society (ACS) in ACS Applied Materials & Interfaces
- Vol. 16 (30) , 40263-40274
Open AccessSequential Self-Assembly of Polystyrene-block-Polydimethylsiloxane for 3D Nanopatterning via Solvent Annealing
This study aims to develop a strategy for the fabrication of multilayer nanopatterns through sequential self-assembly of lamella-forming polystyrene-block-polydimethylsiloxane (PS-b-PDMS) block copolymer (BCP) from solvent annealing. By simply tuning the solvent selectivity, a variety of self-assembled BCP thin-film morphologies, including hexagonal perforated lamellae (HPL), parallel cylinders, and spheres, can be obtained from single-composition PS-b-PDMS. By taking advantage of reactive ion etching (RIE), topographic SiO2 monoliths with well-ordered arrays of hexagonally packed holes, parallel lines, and hexagonally packed dots can be formed. Subsequently, hole-on-dot and line-on-hole hierarchical textures can be created through a layer-by-layer process with RIE treatment as evidenced experimentally and confirmed theoretically. The results demonstrated the feasibility of creating three-dimensional (3D) nanopatterning from the sequential self-assembly of single-composition PS-b-PDMS via solvent annealing, providing an appealing process for nano-MEMS manufacturing based on BCP lithography.
- 13 April 2023
- Published by American Chemical Society (ACS) in ACS Macro Letters
- Vol. 12 (5) , 570-576
Direct Visualization of the Self-Alignment Process for Nanostructured Block Copolymer Thin Films by Transmission Electron Microscopy
Herein, this work aims to directly visualize the morphological evolution of the controlled self-assembly of star-block polystyrene-block-polydimethylsiloxane (PS-b-PDMS) thin films via in situ transmission electron microscopy (TEM) observations. With an environmental chip, possessing a built-in metal wire-based microheater fabricated by the microelectromechanical system (MEMS) technique, in situ TEM observations can be conducted under low-dose conditions to investigate the development of film-spanning perpendicular cylinders in the block copolymer (BCP) thin films via a self-alignment process. Owing to the free-standing condition, a symmetric condition of the BCP thin films can be formed for thermal annealing under vacuum with neutral air surface, whereas an asymmetric condition can be formed by an air plasma treatment on one side of the thin film that creates an end-capped neutral layer. A systematic comparison of the time-resolved self-alignment process in the symmetric and asymmetric conditions can be carried out, giving comprehensive insights for the self-alignment process via the nucleation and growth mechanism.
- 13 April 2023
- Published by American Chemical Society (ACS) in ACS Macro Letters
- Vol. 12 (5) , 570-576
Direct Visualization of the Self-Alignment Process for Nanostructured Block Copolymer Thin Films by Transmission Electron Microscopy
Herein, this work aims to directly visualize the morphological evolution of the controlled self-assembly of star-block polystyrene-block-polydimethylsiloxane (PS-b-PDMS) thin films via in situ transmission electron microscopy (TEM) observations. With an environmental chip, possessing a built-in metal wire-based microheater fabricated by the microelectromechanical system (MEMS) technique, in situ TEM observations can be conducted under low-dose conditions to investigate the development of film-spanning perpendicular cylinders in the block copolymer (BCP) thin films via a self-alignment process. Owing to the free-standing condition, a symmetric condition of the BCP thin films can be formed for thermal annealing under vacuum with neutral air surface, whereas an asymmetric condition can be formed by an air plasma treatment on one side of the thin film that creates an end-capped neutral layer. A systematic comparison of the time-resolved self-alignment process in the symmetric and asymmetric conditions can be carried out, giving comprehensive insights for the self-alignment process via the nucleation and growth mechanism.
- 16 January 2023
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 56 (3) , 841-849
Controlled Orientation of Silicon-Containing Diblock Copolymer Thin Films by Substrate Functionalization Under Vacuum
- 16 January 2023
- Published by American Chemical Society (ACS) in Macromolecules
- Vol. 56 (3) , 841-849
Controlled Orientation of Silicon-Containing Diblock Copolymer Thin Films by Substrate Functionalization Under Vacuum
- 29 July 2022
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 16 (8) , 12686-12694
Vacuum-Driven Orientation of Nanostructured Diblock Copolymer Thin Films
This work aims to demonstrate a facile method for the controlled orientation of nanostructures of block copolymer (BCP) thin films. A simple diblock copolymer system, polystyrene-block-polydimethylsiloxane (PS-b-PDMS), is chosen to demonstrate vacuum-driven orientation for solving the notorious low-surface-energy problem of silicon-based BCP nanopatterning. By taking advantage of the pressure dependence of the surface tension of polymeric materials, a neutral air surface for the PS-b-PDMS thin film can be formed under a high vacuum degree (∼10-4 Pa), allowing the formation of the film-spanning perpendicular cylinders and lamellae upon thermal annealing. In contrast to perpendicular lamellae, a long-range lateral order for forming perpendicular cylinders can be efficiently achieved through the self-alignment mechanism for induced ordering from the top and bottom of the free-standing thin film.
- 29 July 2022
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 16 (8) , 12686-12694
Vacuum-Driven Orientation of Nanostructured Diblock Copolymer Thin Films
This work aims to demonstrate a facile method for the controlled orientation of nanostructures of block copolymer (BCP) thin films. A simple diblock copolymer system, polystyrene-block-polydimethylsiloxane (PS-b-PDMS), is chosen to demonstrate vacuum-driven orientation for solving the notorious low-surface-energy problem of silicon-based BCP nanopatterning. By taking advantage of the pressure dependence of the surface tension of polymeric materials, a neutral air surface for the PS-b-PDMS thin film can be formed under a high vacuum degree (∼10-4 Pa), allowing the formation of the film-spanning perpendicular cylinders and lamellae upon thermal annealing. In contrast to perpendicular lamellae, a long-range lateral order for forming perpendicular cylinders can be efficiently achieved through the self-alignment mechanism for induced ordering from the top and bottom of the free-standing thin film.