Paul Marten
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Interests
Paul Marten has a total of 7 co-authors. Here are the top co-authors by number of shared publications:
- Christoph Baumann
DWI – Leibniz Institute for Interactive Materials
1 shared publication - Davide Campagna
DWI – Leibniz Institute for Interactive Materials Forckenbeckstr. 50 52056 Aachen Germany
1 shared publication - Etienne Rognin
Institute for Manufacturing Department of Engineering University of Cambridge Cambridge UK
1 shared publication - Niamh Willis-Fox
Institute for Manufacturing Department of Engineering University of Cambridge Cambridge UK
1 shared publication - Oliver Weichold
Institute for Building Materials Research, RWTH Aachen University, Schinkelstraße 3, 52062 Aachen, Germany
1 shared publication - Robert Göstl
Department of Chemistry and Biology University of Wuppertal Wuppertal Germany
1 shared publication
Latest Publications
- Open Access
Temperature-Dependent Mechanical Behaviour of Polylactic Acid Plasticised with a Bio-Based Chitin–Lecithin System
Polylactic acid (PLA) is a bio-based thermoplastic whose inherent brittleness limits mechanically demanding applications. This study investigates how a bio-based chitin–lecithin plasticiser system affects the mechanical behaviour of injection-moulded PLA as a function of additive composition, testing temperature, and annealing-induced crystallisation. Tensile and notched Charpy impact tests were performed under ambient conditions, complemented by dynamical mechanical characterisation, tensile testing at 40 and 50 °C, and DSC analysis after annealing at 130 °C for 2 h. Chitin alone increased Young’s modulus from 0.95 ± 0.08 to 1.26 ± 0.02 GPa but reduced ductility and impact strength. In contrast, ternary formulations showed increased deformability at low-to-intermediate additive contents, with fracture strain increasing from 6.87 ± 0.61% for neat PLA to 27.38 ± 3.73%. Dynamical mechanical characterisation showed only a small shift in the glass-transition temperature, while tensile deformability increased strongly as the testing temperature approached the glass-transition range. Annealing lead to crystallinities of approximately 43–45% in the ternary formulations and reduced fracture strain by 86–93%. These results indicate that the chitin–lecithin system promotes deformation of the amorphous PLA phase without a pronounced reduction in bulk glass-transition temperature, while crystallisation largely suppresses this effect.
Open AccessTemperature-Dependent Mechanical Behaviour of Polylactic Acid Plasticised with a Bio-Based Chitin–Lecithin System
Polylactic acid (PLA) is a bio-based thermoplastic whose inherent brittleness limits mechanically demanding applications. This study investigates how a bio-based chitin–lecithin plasticiser system affects the mechanical behaviour of injection-moulded PLA as a function of additive composition, testing temperature, and annealing-induced crystallisation. Tensile and notched Charpy impact tests were performed under ambient conditions, complemented by dynamical mechanical characterisation, tensile testing at 40 and 50 °C, and DSC analysis after annealing at 130 °C for 2 h. Chitin alone increased Young’s modulus from 0.95 ± 0.08 to 1.26 ± 0.02 GPa but reduced ductility and impact strength. In contrast, ternary formulations showed increased deformability at low-to-intermediate additive contents, with fracture strain increasing from 6.87 ± 0.61% for neat PLA to 27.38 ± 3.73%. Dynamical mechanical characterisation showed only a small shift in the glass-transition temperature, while tensile deformability increased strongly as the testing temperature approached the glass-transition range. Annealing lead to crystallinities of approximately 43–45% in the ternary formulations and reduced fracture strain by 86–93%. These results indicate that the chitin–lecithin system promotes deformation of the amorphous PLA phase without a pronounced reduction in bulk glass-transition temperature, while crystallisation largely suppresses this effect.
- Open Access
- 29 July 2022
- Published by Wiley in Journal of Polymer Science
- Vol. 60 (22) , 3128-3133
Regiochemical effects for the mechanochemical activation of 9‐π‐extended anthracene‐maleimide Diels–Alder adducts
The attachment point of the polymer chain to a force‐responsive molecular unit (mechanophore) is a decisive parameter determining bond scission rate and ultimately the mechanochemical reaction outcome. However, such regiochemical polymer substituent effects have not yet been investigated for 9‐π‐extended anthracene‐maleimide Diels‐Alder adducts. Here we combine three methods, namely ultrasonication, CoGEF computation, and flow activation, to understand the influence of the pulling point location on the mechanochemical reactivity of this mechanophore class. We find minor mechanochemical reactivity differences between the investigated constitutional mechanophore isomers. Concomitantly, our results highlight the capabilities and limitations of the employed experimental techniques for such delicate variances and raise the question whether these are relevant for mechanochemical applications in a material context.
- 29 July 2022
- Published by Wiley in Journal of Polymer Science
- Vol. 60 (22) , 3128-3133
Open AccessRegiochemical effects for the mechanochemical activation of 9‐π‐extended anthracene‐maleimide Diels–Alder adducts
The attachment point of the polymer chain to a force‐responsive molecular unit (mechanophore) is a decisive parameter determining bond scission rate and ultimately the mechanochemical reaction outcome. However, such regiochemical polymer substituent effects have not yet been investigated for 9‐π‐extended anthracene‐maleimide Diels‐Alder adducts. Here we combine three methods, namely ultrasonication, CoGEF computation, and flow activation, to understand the influence of the pulling point location on the mechanochemical reactivity of this mechanophore class. We find minor mechanochemical reactivity differences between the investigated constitutional mechanophore isomers. Concomitantly, our results highlight the capabilities and limitations of the employed experimental techniques for such delicate variances and raise the question whether these are relevant for mechanochemical applications in a material context.