Ahmed M. Teamah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Ahmed M. Teamah has a total of 8 co-authors. Here are the top co-authors by number of shared publications:
- Mohamed Hamed Arisha
Department of Mechanical Engineering, McMaster University, Hamilton, ON L8S4L7, Canada
4 shared publications Mohamed S. Hamed
3 shared publications- Sumanth Shankar
Department of Mechanical Engineering, McMaster University, Hamilton, ON L8S4L7, Canada
3 shared publications - Abdelfatah M. Teamah
Department of Mechanical Engineering, McMaster University, Hamilton, ON L8S4L7, Canada
1 shared publication Mohamed S. Hamned
1 shared publication- Ravi Peri
Department of Mechanical Engineering, McMaster University, Hamilton, ON L8S4L7, Canada
1 shared publication
Latest Publications
- Open Access
Axial Solidification Experiments to Mimic Net-Shaped Castings of Aluminum Alloys—Interfacial Heat-Transfer Coefficient and Thermal Diffusivity
Net-shaped casting processes in the automotive industry have proved to be difficult to simulate due to the complexities of the interactions amongst thermal, fluid, and solute transport regimes in the solidifying domain, along with the interface. The existing casting simulation software lacks the necessary real-time estimation of thermophysical properties (thermal diffusivity and thermal conductivity) and the interfacial heat-transfer coefficient (IHTC) to evaluate the thermal resistances in a casting process and solve the temperature in the solidifying domain. To address these shortcomings, an axial directional solidification experiment setup was developed to map the thermal data as the melt solidifies unidirectionally from the chill surface under unsteady-state conditions. A Dilute Eutectic Cast Aluminum (DECA) alloy, Al-5Zn-1Mg-1.2Fe-0.07Ti, Eutectic Cast Aluminum (ECA) alloys (A365 and A383), and pure Al (P0303) were used to demonstrate the validity of the experiments to evaluate the thermal diffusivity (α) of both the solid and liquid phases of the solidifying metal using an inverse heat-transfer analysis (IHTA). The thermal diffusivity varied from 0.2 to 1.9 cm2/s while the IHTC changed from 9500 to 200 W/m2K for different alloys in the solid and liquid phases. The heat flux was estimated from the chill side with transient temperature distributions estimated from IHTA for either side of the mold–metal interface as an input to compute the interfacial heat-transfer coefficient (IHTC). The results demonstrate the reliability of the axial solidification experiment apparatus in accurately providing input to the casting simulation software and aid in reproducing casting numerical simulation models efficiently.
Open AccessAxial Solidification Experiments to Mimic Net-Shaped Castings of Aluminum Alloys—Interfacial Heat-Transfer Coefficient and Thermal Diffusivity
Net-shaped casting processes in the automotive industry have proved to be difficult to simulate due to the complexities of the interactions amongst thermal, fluid, and solute transport regimes in the solidifying domain, along with the interface. The existing casting simulation software lacks the necessary real-time estimation of thermophysical properties (thermal diffusivity and thermal conductivity) and the interfacial heat-transfer coefficient (IHTC) to evaluate the thermal resistances in a casting process and solve the temperature in the solidifying domain. To address these shortcomings, an axial directional solidification experiment setup was developed to map the thermal data as the melt solidifies unidirectionally from the chill surface under unsteady-state conditions. A Dilute Eutectic Cast Aluminum (DECA) alloy, Al-5Zn-1Mg-1.2Fe-0.07Ti, Eutectic Cast Aluminum (ECA) alloys (A365 and A383), and pure Al (P0303) were used to demonstrate the validity of the experiments to evaluate the thermal diffusivity (α) of both the solid and liquid phases of the solidifying metal using an inverse heat-transfer analysis (IHTA). The thermal diffusivity varied from 0.2 to 1.9 cm2/s while the IHTC changed from 9500 to 200 W/m2K for different alloys in the solid and liquid phases. The heat flux was estimated from the chill side with transient temperature distributions estimated from IHTA for either side of the mold–metal interface as an input to compute the interfacial heat-transfer coefficient (IHTC). The results demonstrate the reliability of the axial solidification experiment apparatus in accurately providing input to the casting simulation software and aid in reproducing casting numerical simulation models efficiently.
- Open Access
Estimation of Thermophysical Properties as Functions of Temperature in Rapid Radial Solidification of Metallic Alloys
Recent global efforts to produce lightweight electrified vehicles have motivated the push toward advanced lightweight materials which led to the creation of novel alloys optimized for use in high-pressure die casting (HPDC). HPDC enables the fabrication of near-net-shape automotive parts, significantly reducing or eliminating additional machining steps. A key feature of HPDC is the extremely fast cooling that forces the alloy to solidify within only a few seconds. Because of these rapid cooling conditions, it becomes essential to accurately evaluate the thermophysical behavior of newly designed lightweight alloys during severe quenching. Precisely quantifying these material properties is crucial for properly controlling HPDC operations and for building reliable numerical models that simulate filling and solidification. The thermophysical characteristics of such alloys vary markedly with temperature, especially when the material undergoes the fast solidification typical of HPDC. Therefore, understanding how these properties change with temperature during intense cooling becomes a critical requirement in alloy development. To address this need, a dedicated experimental system was designed to solidify molten metal samples under controlled and variable cooling conditions by applying multiple impinging water jets. An inverse heat-transfer algorithm was formulated to extract temperature-dependent thermal conductivity and diffusivity of the alloy as it solidifies under rapid cooling. To verify the reliability of both the inverse model and the measurements, experiments were performed using pure Tin, a reference material with well-documented thermophysical properties. The computed thermophysical properties of Tin were benchmarked against values reported in the literature and demonstrated reasonable consistency, with a maximum deviation of 13.6%.
Open AccessEstimation of Thermophysical Properties as Functions of Temperature in Rapid Radial Solidification of Metallic Alloys
Recent global efforts to produce lightweight electrified vehicles have motivated the push toward advanced lightweight materials which led to the creation of novel alloys optimized for use in high-pressure die casting (HPDC). HPDC enables the fabrication of near-net-shape automotive parts, significantly reducing or eliminating additional machining steps. A key feature of HPDC is the extremely fast cooling that forces the alloy to solidify within only a few seconds. Because of these rapid cooling conditions, it becomes essential to accurately evaluate the thermophysical behavior of newly designed lightweight alloys during severe quenching. Precisely quantifying these material properties is crucial for properly controlling HPDC operations and for building reliable numerical models that simulate filling and solidification. The thermophysical characteristics of such alloys vary markedly with temperature, especially when the material undergoes the fast solidification typical of HPDC. Therefore, understanding how these properties change with temperature during intense cooling becomes a critical requirement in alloy development. To address this need, a dedicated experimental system was designed to solidify molten metal samples under controlled and variable cooling conditions by applying multiple impinging water jets. An inverse heat-transfer algorithm was formulated to extract temperature-dependent thermal conductivity and diffusivity of the alloy as it solidifies under rapid cooling. To verify the reliability of both the inverse model and the measurements, experiments were performed using pure Tin, a reference material with well-documented thermophysical properties. The computed thermophysical properties of Tin were benchmarked against values reported in the literature and demonstrated reasonable consistency, with a maximum deviation of 13.6%.
- Open Access
Experimental and Numerical Replication of Thermal Conditions in High-Pressure Die-Casting Process
Acquiring reliable thermal data during the high-pressure die-casting (HPDC) process remains a significant challenge due to its complexity and rapidly evolving thermal environment. In industrial settings, the influence of process parameters is typically evaluated after solidification by examining the final casting quality, as direct temperature measurements within the die during operation are difficult to obtain. Additionally, most casting simulation tools lack accurate correlations for the interfacial heat transfer coefficient (IHTC) as a function of process parameters. To address this limitation, a laboratory-scale hot chamber die-casting (HCDC) apparatus was developed to replicate the fluid flow and the thermal conditions of industrial HPDC operation while enabling direct thermal measurements inside the die cavity using embedded thermocouples. The molten metal temperature was estimated using the lumped capacitance method, and the IHTC was determined through a custom inverse heat conduction algorithm incorporating an adaptive forward time-stepping scheme. This algorithm was validated by solving the forward heat conduction problem using the ANSYS 2025 R1 Transient Thermal solver. The experimentally obtained IHTC values showed good agreement with those measured during industrial HPDC trials, with a maximum deviation of about 14% in the peak value, while the full width at half maximum (FWHM) differed by less than 12%. These results confirm that the developed HCDC setup can reliably reproduce industrial thermal conditions and generate high-quality thermal data that can be used in numerical casting simulations.
Open AccessExperimental and Numerical Replication of Thermal Conditions in High-Pressure Die-Casting Process
Acquiring reliable thermal data during the high-pressure die-casting (HPDC) process remains a significant challenge due to its complexity and rapidly evolving thermal environment. In industrial settings, the influence of process parameters is typically evaluated after solidification by examining the final casting quality, as direct temperature measurements within the die during operation are difficult to obtain. Additionally, most casting simulation tools lack accurate correlations for the interfacial heat transfer coefficient (IHTC) as a function of process parameters. To address this limitation, a laboratory-scale hot chamber die-casting (HCDC) apparatus was developed to replicate the fluid flow and the thermal conditions of industrial HPDC operation while enabling direct thermal measurements inside the die cavity using embedded thermocouples. The molten metal temperature was estimated using the lumped capacitance method, and the IHTC was determined through a custom inverse heat conduction algorithm incorporating an adaptive forward time-stepping scheme. This algorithm was validated by solving the forward heat conduction problem using the ANSYS 2025 R1 Transient Thermal solver. The experimentally obtained IHTC values showed good agreement with those measured during industrial HPDC trials, with a maximum deviation of about 14% in the peak value, while the full width at half maximum (FWHM) differed by less than 12%. These results confirm that the developed HCDC setup can reliably reproduce industrial thermal conditions and generate high-quality thermal data that can be used in numerical casting simulations.
- Open Access
- 21 January 2024
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 198
Numerical and experimental study of a multiphase flow inside a self-contained drum motor drive system
- 21 January 2024
- Published by Elsevier in International Journal of Thermal Sciences
- Vol. 198
Open AccessNumerical and experimental study of a multiphase flow inside a self-contained drum motor drive system
- Open Access
- 27 November 2023
- Published by Elsevier in International Journal of Thermofluids
- Vol. 20, 100525
Cooling of a synchronous electric motor using an axial air flow
- 27 November 2023
- Published by Elsevier in International Journal of Thermofluids
- Vol. 20, 100525
Open AccessCooling of a synchronous electric motor using an axial air flow
- 1 January 2023
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 10 (1) , 45
Numerical and Experimental Study of The Viscous Dissipation of Oil inside the Electric Motor’s Gap
The Volume 10, published for JFFHMT Journal.
- 1 January 2023
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 10 (1) , 45
Numerical and Experimental Study of The Viscous Dissipation of Oil inside the Electric Motor’s Gap
The Volume 10, published for JFFHMT Journal.
- Open Access
- 1 August 2022
- Published by Elsevier in International Journal of Thermofluids
- Vol. 15
Numerical investigation of thermal losses within an internal gear train submerged in a multiphase flow and enclosed in a rotating casing
- 1 August 2022
- Published by Elsevier in International Journal of Thermofluids
- Vol. 15
Open AccessNumerical investigation of thermal losses within an internal gear train submerged in a multiphase flow and enclosed in a rotating casing
- Open Access
- 1 January 2022
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 9 (1) , 101-105
Numerical Study of Electric Motors Cooling Using an Axial Air Flow
The Volume 9, published for JFFHMT Journal.
- 1 January 2022
- Published by Avestia Publishing in Journal of Fluid Flow, Heat and Mass Transfer
- Vol. 9 (1) , 101-105
Open AccessNumerical Study of Electric Motors Cooling Using an Axial Air Flow
The Volume 9, published for JFFHMT Journal.