Emre Ertürk
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Emre Ertürk has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Philipp Höfer
University of the Bundeswehr Munich
2 shared publications- Philipp Höfer
Institute of Lightweight Engineering, University of the Bundeswehr Munich
2 shared publications Andreas Wohninsland
1 shared publicationBruno Musil
Institute of Lightweight Engineering, Universität der Bundeswehr München, Neubiberg, Germany
1 shared publicationChristian Felber
Institute of Materials Science, Universität der Bundeswehr München, Neubiberg, Germany
1 shared publicationChristoph Stark
Modell- und Formenbau Blasius GERG GmbH
1 shared publication
Latest Publications
- 26 July 2025
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 142
Laser treatment of PBF-LB manufactured Ti6Al4V parts for structural adhesive bonding
- 26 July 2025
- Published by Elsevier in International Journal of Adhesion and Adhesives
- Vol. 142
Laser treatment of PBF-LB manufactured Ti6Al4V parts for structural adhesive bonding
- 27 July 2024
- Published by Springer Nature
- p. 155-168
Analytical and Numerical Modeling of Aramid Honeycomb Cores
- 27 July 2024
- Published by Springer Nature
- p. 155-168
Analytical and Numerical Modeling of Aramid Honeycomb Cores
- Open Access
- 12 May 2023
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 8 (4) , 719-731
Surface morphology influences of PBF-LB manufactured Ti6Al4V parts on adhesive bond strength—investigation of as-built and surface-treated conditions
Additive manufacturing in combination with adhesive bonding enables high lightweight potential in structural design. A decisive factor for high adhesive bond performance are the surface properties. In the present work, the surface morphology of laser powder bed fusion (PBF-LB) processed Ti6Al4V parts was investigated in the as-built condition for the build orientations 0°, 45°, 90°. Furthermore, subsequent surface treatment by grit blasting or laser treatment allowed to modify the surface morphology and examine its effect on the bond strength. The surface characteristics were assessed using scanning electron microscopy, laser confocal microscopy and contact angle measurements. Evaluating the bond strength was done for tensile loading by centrifugal adhesion testing. The lowest bond strength was found for 0° oriented specimens, while the 45° and 90° oriented samples showed similar strengths. Fracture surface analysis of the as-built surfaces showed that the partially melted particles remain attached and cause mechanical interlocking. Furthermore, surface treatment by grit blasting allowed a minor improvement of the bond strength, while with laser treatment a significant increase was possible.
- 12 May 2023
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 8 (4) , 719-731
Open AccessSurface morphology influences of PBF-LB manufactured Ti6Al4V parts on adhesive bond strength—investigation of as-built and surface-treated conditions
Additive manufacturing in combination with adhesive bonding enables high lightweight potential in structural design. A decisive factor for high adhesive bond performance are the surface properties. In the present work, the surface morphology of laser powder bed fusion (PBF-LB) processed Ti6Al4V parts was investigated in the as-built condition for the build orientations 0°, 45°, 90°. Furthermore, subsequent surface treatment by grit blasting or laser treatment allowed to modify the surface morphology and examine its effect on the bond strength. The surface characteristics were assessed using scanning electron microscopy, laser confocal microscopy and contact angle measurements. Evaluating the bond strength was done for tensile loading by centrifugal adhesion testing. The lowest bond strength was found for 0° oriented specimens, while the 45° and 90° oriented samples showed similar strengths. Fracture surface analysis of the as-built surfaces showed that the partially melted particles remain attached and cause mechanical interlocking. Furthermore, surface treatment by grit blasting allowed a minor improvement of the bond strength, while with laser treatment a significant increase was possible.
- 6 August 2022
- Published by Springer Nature
- p. 175-188
3D Material Model for Additive Manufactured Metallic Parts
- 6 August 2022
- Published by Springer Nature
- p. 175-188
3D Material Model for Additive Manufactured Metallic Parts