Zamira Sattinova
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Zamira Sattinova has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Gaukhar Ramazanova
Satbayev University
6 shared publications - Uzak K. Zhapbasbayev
Scientific and Production Laboratory “Energy Modeling”, Satbayev University, Almaty 050013, Kazakhstan
3 shared publications - Bakytzhan Assilbekov
Institute of Ionosphere, Almaty 050020, Kazakhstan
2 shared publications - Elmira Mussenova
E.A. Buketov Karaganda State University, Karaganda 100028, Kazakhstan
2 shared publications T.N. Bekenov
2 shared publications- Ainash Shabdirova
Oil and Gas Faculty, Atyrau University of Oil and Gas, Atyrau 060000, Kazakhstan
1 shared publication
Latest Publications
- Open Access
- 31 March 2026
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 23 (1 (55)) , 101-112
TURBULENT FLOW OF VISCOELASTIC FLUID BASED ON THE REYNOLDS STRESS MODEL
This article presents the results of applying a turbulent stress model to the simulation of high-viscosity viscoelastic fluid flow in a pipe. The model is used to numerically determine averaged velocity and stress fields within the Navier–Stokes equations. The proposed model takes into account the influence of the Sisko fluid rheology on turbulent momentum transfer, providing a physically sound description of the interaction between turbulence and non-Newtonian effects. Calculations for a Newtonian fluid are performed as a baseline for evaluating the effectiveness of the proposed approach. It is shown that for Sisko fluid, the averaged velocity profile in universal coordinates is systematically shifted upward compared to the Newtonian case, indicating weakening of turbulent momentum transfer and a decrease in hydrodynamic drag. It is established that the level of axial velocity fluctuations exceeds the Newtonian value, while radial fluctuations are lower, indicating pronounced anisotropy of turbulent stresses. The viscoelastic properties of the fluid lead to a reduction in turbulent friction due to the suppression of small-scale vortex structures and, as a consequence, to a reduction in the hydraulic resistance of the pipe.
- 31 March 2026
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 23 (1 (55)) , 101-112
Open AccessTURBULENT FLOW OF VISCOELASTIC FLUID BASED ON THE REYNOLDS STRESS MODEL
This article presents the results of applying a turbulent stress model to the simulation of high-viscosity viscoelastic fluid flow in a pipe. The model is used to numerically determine averaged velocity and stress fields within the Navier–Stokes equations. The proposed model takes into account the influence of the Sisko fluid rheology on turbulent momentum transfer, providing a physically sound description of the interaction between turbulence and non-Newtonian effects. Calculations for a Newtonian fluid are performed as a baseline for evaluating the effectiveness of the proposed approach. It is shown that for Sisko fluid, the averaged velocity profile in universal coordinates is systematically shifted upward compared to the Newtonian case, indicating weakening of turbulent momentum transfer and a decrease in hydrodynamic drag. It is established that the level of axial velocity fluctuations exceeds the Newtonian value, while radial fluctuations are lower, indicating pronounced anisotropy of turbulent stresses. The viscoelastic properties of the fluid lead to a reduction in turbulent friction due to the suppression of small-scale vortex structures and, as a consequence, to a reduction in the hydraulic resistance of the pipe.
- Open Access
- 16 June 2025
- Published by Karagandy University of the name of academician E.A. Buketov in Bulletin of the Karaganda University "Physics Series"
- Vol. 11830 (2) , 67-74
Modeling of Turbulent Non-Isothermal Flow in a Heating Network Pipe
The article presents a mathematical model of turbulent non-isothermal flow of viscoplastic fluid in a pipewith a sudden expansion of the heat network. Heat exchange of non-isothermal flow of viscoplastic fluid withcold environment leads to an increase in its viscosity and yield strength. Shvedov-Bingham rheological modelrepresents the viscoplastic state of fluid. The Reynolds Stress Model (RSM) turbulence model describes theproperties of anisotropy of the velocity components of pulsating motion in a pipe with a sudden expansion. Inaddition, the ability to predict turbulence anisotropy of the RSM model is used to construct a linear model ofturbulent viscosity. Calculation data are obtained for different values of Reynolds and Bingham numbers. Thecalculation results show that with an increase in the Bingham number, the circulation zone decreases behindthe section of the sudden expansion of the pipe. The results of the comparison of the radial profiles of thenormalized axial mean and fluctuation velocity with the experimental data along the pipe with sudden expansionare given. The results show the anisotropic property of the axial and radial profiles of the velocity of fluctuationmovement, which are in agreement with the data of the DNS (Direct Numerical Simulation) model.
- 16 June 2025
- Published by Karagandy University of the name of academician E.A. Buketov in Bulletin of the Karaganda University "Physics Series"
- Vol. 11830 (2) , 67-74
Open AccessModeling of Turbulent Non-Isothermal Flow in a Heating Network Pipe
The article presents a mathematical model of turbulent non-isothermal flow of viscoplastic fluid in a pipewith a sudden expansion of the heat network. Heat exchange of non-isothermal flow of viscoplastic fluid withcold environment leads to an increase in its viscosity and yield strength. Shvedov-Bingham rheological modelrepresents the viscoplastic state of fluid. The Reynolds Stress Model (RSM) turbulence model describes theproperties of anisotropy of the velocity components of pulsating motion in a pipe with a sudden expansion. Inaddition, the ability to predict turbulence anisotropy of the RSM model is used to construct a linear model ofturbulent viscosity. Calculation data are obtained for different values of Reynolds and Bingham numbers. Thecalculation results show that with an increase in the Bingham number, the circulation zone decreases behindthe section of the sudden expansion of the pipe. The results of the comparison of the radial profiles of thenormalized axial mean and fluctuation velocity with the experimental data along the pipe with sudden expansionare given. The results show the anisotropic property of the axial and radial profiles of the velocity of fluctuationmovement, which are in agreement with the data of the DNS (Direct Numerical Simulation) model.
- Open Access
- 31 March 2025
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 22 (1 (51)) , 103-114
STUDY OF THE EFFECT OF HEAT TRANSFER DURING MOLDING OF TERMOPLASTIC BERYLLIUM OXIDE CERAMICS
Beryllium oxide (BeO) ceramics formed with the use of ultrasound exhibit more intense sintering, lower shrinkage, and a reduced sintering temperature compared to ceramics produced without ultrasound. The effectiveness of ultrafast sintering is dependent on the cohesion of ceramic agglomeration and the proper arrangement of particles. Rheological properties thermoplastic slurry changed as a result of ultrasound activation. These changes are related to dispersion phase processes and mass transfer. Ultrasonic activation also slightly enhances the properties of the castings. The increase in the density and strength of castings is explained by the effective reduction of shrinkage under the influence of ultrasound during hardening. That is, compensation for the deposition of the Ingot is determined by filling with a liquid slurry and its compaction under the influence of pressure. For ultrasonic injection of thermoplastic beryllium oxide slurry, formulations with a binder content ranging from 9,5 to 11,7% are recommended. Because these binder compositions are mixed with beryllium powder, turning into a high-strength slurry, forming ceramics that can withstand large temperatures.
- 31 March 2025
- Published by Karagandy University of the name of academician E.A. Buketov in Eurasian Physical Technical Journal
- Vol. 22 (1 (51)) , 103-114
Open AccessSTUDY OF THE EFFECT OF HEAT TRANSFER DURING MOLDING OF TERMOPLASTIC BERYLLIUM OXIDE CERAMICS
Beryllium oxide (BeO) ceramics formed with the use of ultrasound exhibit more intense sintering, lower shrinkage, and a reduced sintering temperature compared to ceramics produced without ultrasound. The effectiveness of ultrafast sintering is dependent on the cohesion of ceramic agglomeration and the proper arrangement of particles. Rheological properties thermoplastic slurry changed as a result of ultrasound activation. These changes are related to dispersion phase processes and mass transfer. Ultrasonic activation also slightly enhances the properties of the castings. The increase in the density and strength of castings is explained by the effective reduction of shrinkage under the influence of ultrasound during hardening. That is, compensation for the deposition of the Ingot is determined by filling with a liquid slurry and its compaction under the influence of pressure. For ultrasonic injection of thermoplastic beryllium oxide slurry, formulations with a binder content ranging from 9,5 to 11,7% are recommended. Because these binder compositions are mixed with beryllium powder, turning into a high-strength slurry, forming ceramics that can withstand large temperatures.
- Open Access
Computational Investigation of the Influencing Parameters on the Solidification of Thermoplastic Beryllium Oxide Slurry in a Cylindrical Shell
This article presents a computational study of the influencing parameters on the solidification of the thermoplastic beryllium oxide slurry in an annular forming cavity. The main purpose of this paper is to study the effect of cooling and casting conditions on the solidification of the BeO suspension by considering the temperature-dependent rheological and physical properties. The results of calculations of the Bingham–Papanastasiou rheological model with experimental data in the intervals of phase transitions with different casting rates of beryllium ceramics have been validated. The use of the regularization parameter made it possible to approximate the flow of the slurry at all levels of its shear rates as highly viscous, followed by a continuous transition to a solid state. The speed of heat removal from the molding during the solidification period is determined by the speed of movement of the slurry and the temperature field on which the width of the transition region depends. The process of solidification of the slurry mass has been evaluated by changing its heat flow distribution and density along the length of the concentric channel. The obtained model calculation results make it possible to control the casting process and eventually realize a uniform structure of castings.
Open AccessComputational Investigation of the Influencing Parameters on the Solidification of Thermoplastic Beryllium Oxide Slurry in a Cylindrical Shell
This article presents a computational study of the influencing parameters on the solidification of the thermoplastic beryllium oxide slurry in an annular forming cavity. The main purpose of this paper is to study the effect of cooling and casting conditions on the solidification of the BeO suspension by considering the temperature-dependent rheological and physical properties. The results of calculations of the Bingham–Papanastasiou rheological model with experimental data in the intervals of phase transitions with different casting rates of beryllium ceramics have been validated. The use of the regularization parameter made it possible to approximate the flow of the slurry at all levels of its shear rates as highly viscous, followed by a continuous transition to a solid state. The speed of heat removal from the molding during the solidification period is determined by the speed of movement of the slurry and the temperature field on which the width of the transition region depends. The process of solidification of the slurry mass has been evaluated by changing its heat flow distribution and density along the length of the concentric channel. The obtained model calculation results make it possible to control the casting process and eventually realize a uniform structure of castings.
- 1 January 2024
- Published by Engineered Science Publisher in Engineered Science
Simulation of Hot Casting Shrinkage of Thermoplastic Beryllium Oxide Slurries with Ultrasonic Activation
Detailed tracking of changes in the temperature-phase fields of the casting process clearly represents the shrinkage and kinetics of solidification
- 1 January 2024
- Published by Engineered Science Publisher in Engineered Science
Simulation of Hot Casting Shrinkage of Thermoplastic Beryllium Oxide Slurries with Ultrasonic Activation
Detailed tracking of changes in the temperature-phase fields of the casting process clearly represents the shrinkage and kinetics of solidification
- 6 August 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (21) , 31102-31110
Mathematical modeling of the rheological behavior of thermoplastic slurry in the molding process of beryllium ceramics
- 6 August 2022
- Published by Elsevier in Ceramics International
- Vol. 48 (21) , 31102-31110
Mathematical modeling of the rheological behavior of thermoplastic slurry in the molding process of beryllium ceramics
- Open Access
- 10 December 2018
- Published by MDPI AG in Proceedings
- Vol. 2 (22) , 1391
Investigation of Thermodynamic Properties of the Slurry of the Molding Process Beryllium Ceramics
Obtaining of ceramic fabrications by hot molding from dispersion materials with anomalous physical properties, such as BeO is particularly complicated. In this case, the difficulties of obtaining of quality products were caused firstly by thermal properties of beryllium oxide, in particular, its unique thermal conductivity. Results of experiments and calculations of the mathematical model of the motion and heat exchange of the slurry mass in the annular cavity are presented. The results of experiments and calculations show the process of molding of the slurry in the annular cavity.
- 10 December 2018
- Published by MDPI AG in Proceedings
- Vol. 2 (22) , 1391
Open AccessInvestigation of Thermodynamic Properties of the Slurry of the Molding Process Beryllium Ceramics
Obtaining of ceramic fabrications by hot molding from dispersion materials with anomalous physical properties, such as BeO is particularly complicated. In this case, the difficulties of obtaining of quality products were caused firstly by thermal properties of beryllium oxide, in particular, its unique thermal conductivity. Results of experiments and calculations of the mathematical model of the motion and heat exchange of the slurry mass in the annular cavity are presented. The results of experiments and calculations show the process of molding of the slurry in the annular cavity.
- 11 February 2013
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 33 (8) , 1403-1411
Modeling of the beryllia ceramics formation process
- 11 February 2013
- Published by Elsevier in Journal of the European Ceramic Society
- Vol. 33 (8) , 1403-1411
Modeling of the beryllia ceramics formation process