Tanya Aycan Başer
Research Subjects
Tanya Aycan Başer has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
- Mehtap Hidiroğlu
Coşkunöz Mold Machine, R&D Center, Bursa, Turkey
4 shared publications Alperen Bayram
Coşkunöz Kalıp Makina (CKM) R&D Center , Bursa , Türkiye
2 shared publicationsBurak Barutçuoğlu
Department of Materials Engineering , Kocaeli University , Kocaeli , Türkiye
2 shared publicationsErsoy Erişir
Kocaeli University, Kocaeli, Turkey
2 shared publications- Nizamettin Kahraman
Karabük Üniversitesi
2 shared publications Oğuz Gürkan Bilir
Department of Materials Engineering , Kocaeli University , Kocaeli , Türkiye
2 shared publications
Latest Publications
- Open Access
- 24 March 2025
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 13 (1) , 60-74
Galvaniz Kaplı 3. Nesil Çeliklerde Nokta Direnç Kaynağı Sonrası Sıvı Metal Kırılganlığı Oluşumu
3. nesil çelikler, ağırlık azaltma çalışmaları kapsamında son yıllarda otomotiv endüstrisinin uygulamalarında büyük bir öneme sahiptir. Özel üretim yöntemine sahip 3. nesil çeliklerin şekillendirme problemleri ile birlikte kaynaklanabilirliği de yoğun olarak çalışılmaktadır. Genellikle galvaniz kaplamalı olarak tercih edilen bu çeliklerin nokta direnç kaynağı (NDK) sırasında, galvaniz kaplamada yer alan çinko (Zn) elementinin ergime derecesinin düşük olması nedeniyle sıvı faza geçmektedir. Bu durum ergimiş Zn atomlarının kaynak sonrası ana malzemeye difüzyonu ile sıvı metal kırılganlığına (SMK) neden olmaktadır. Kaynak bölgesinde meydana gelen SMK hassasiyeti, ana malzemede mikro çatlaklara sebebiyet verebilmektedir. Ayrıca SMK kaynak bölgesinin mekanik özelliklerini de olumsuz yönde etkilemektedir. Bu çalışma, nokta direnç kaynağı sonrasında oluşan SMK hassasiyeti üzerine yapılan literatür incelemelerinin derlemesini içermektedir. Çalışmada 3. nesil çelik grubunun mekanik özelliklerinin ve mikroyapısının SMK hassasiyetine etkileri anlatılmış olup, aynı zamanda farklı galvaniz kaplama türlerinin SMK oluşumuna etkileri sunulmuştur. Son olarak, nokta direnç kaynağı sırasında SMK hassasiyetinin olası mekanizmaları tartışılmış ve oluşumunu bastırmak için uygun yöntemler önerilmiştir.
- 24 March 2025
- Published by Gazi Universitesi Fen Bilimleri Dergisi Part C: Tasarim ve Teknoloji in Gazi Üniversitesi Fen Bilimleri Dergisi Part C: Tasarım ve Teknoloji
- Vol. 13 (1) , 60-74
Open AccessGalvaniz Kaplı 3. Nesil Çeliklerde Nokta Direnç Kaynağı Sonrası Sıvı Metal Kırılganlığı Oluşumu
3. nesil çelikler, ağırlık azaltma çalışmaları kapsamında son yıllarda otomotiv endüstrisinin uygulamalarında büyük bir öneme sahiptir. Özel üretim yöntemine sahip 3. nesil çeliklerin şekillendirme problemleri ile birlikte kaynaklanabilirliği de yoğun olarak çalışılmaktadır. Genellikle galvaniz kaplamalı olarak tercih edilen bu çeliklerin nokta direnç kaynağı (NDK) sırasında, galvaniz kaplamada yer alan çinko (Zn) elementinin ergime derecesinin düşük olması nedeniyle sıvı faza geçmektedir. Bu durum ergimiş Zn atomlarının kaynak sonrası ana malzemeye difüzyonu ile sıvı metal kırılganlığına (SMK) neden olmaktadır. Kaynak bölgesinde meydana gelen SMK hassasiyeti, ana malzemede mikro çatlaklara sebebiyet verebilmektedir. Ayrıca SMK kaynak bölgesinin mekanik özelliklerini de olumsuz yönde etkilemektedir. Bu çalışma, nokta direnç kaynağı sonrasında oluşan SMK hassasiyeti üzerine yapılan literatür incelemelerinin derlemesini içermektedir. Çalışmada 3. nesil çelik grubunun mekanik özelliklerinin ve mikroyapısının SMK hassasiyetine etkileri anlatılmış olup, aynı zamanda farklı galvaniz kaplama türlerinin SMK oluşumuna etkileri sunulmuştur. Son olarak, nokta direnç kaynağı sırasında SMK hassasiyetinin olası mekanizmaları tartışılmış ve oluşumunu bastırmak için uygun yöntemler önerilmiştir.
- Open Access
- 11 December 2024
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 5 (1) , 147-157
X3CrNiMo13-4 martenzitik paslanmaz çeliklerde fırında sert lehimleme prosesinde kullanılan koruyucu gaz karışımlarının yorulma performansına etkisi
Fırında sert lehimleme, enerji teknolojisi, havacılık, uzay ve otomotiv endüstrisi alanlarında teknik gelişim için öncü rol oynayan, düşük maliyetli bir birleştirme teknolojisidir. Sert lehimleme işleminin fırın içerisinde vakumlu ortamda değil, koruyucu gaz ve karışımlarının kullanılması durumunda, gaz kompozisyonunun birleştirilmiş parçanın yorulma performansını etkilediği bilinmektedir. Bu çalışmada, X3CrNiMo13-4 martenzitik paslanmaz çelik malzemelerin Au18Ni alaşımı ara bağlayıcı tabaka kullanılarak iki farklı koruyucu gaz ortamında (%93 Ar - %7 H2 ve %100 H2) fırında sert lehimleme özellikleri araştırılmıştır. Çalışmada fırında sert lehimleme prosesi sırasında kullanılan farklı koruyucu gazların birleştirilmiş bölgenin yorulma dayanımı ile mikroyapı ve sertlik özelliklerine etkisi incelenmiştir. Ayrıca mikroyapı ve kırılma yüzeyleri üzerinden yapılan karakterizasyon çalışmaları, yorulma testi sonuçları ile karşılaştırılarak değerlendirilmiştir. Yorulma testleri sonucunda %93 Ar - %7 H2 koruyucu gaz altında 20.000 çevrimde σnom,max değeri 250 MPa iken, %100 H2 koruyucu gazı kullanıldığında bu değer 450 MPa’a yükseldiği belirlenmiştir.
- 11 December 2024
- Published by Journal of Innovative Engineering and Natural Science in Journal of Innovative Engineering and Natural Science
- Vol. 5 (1) , 147-157
Open AccessX3CrNiMo13-4 martenzitik paslanmaz çeliklerde fırında sert lehimleme prosesinde kullanılan koruyucu gaz karışımlarının yorulma performansına etkisi
Fırında sert lehimleme, enerji teknolojisi, havacılık, uzay ve otomotiv endüstrisi alanlarında teknik gelişim için öncü rol oynayan, düşük maliyetli bir birleştirme teknolojisidir. Sert lehimleme işleminin fırın içerisinde vakumlu ortamda değil, koruyucu gaz ve karışımlarının kullanılması durumunda, gaz kompozisyonunun birleştirilmiş parçanın yorulma performansını etkilediği bilinmektedir. Bu çalışmada, X3CrNiMo13-4 martenzitik paslanmaz çelik malzemelerin Au18Ni alaşımı ara bağlayıcı tabaka kullanılarak iki farklı koruyucu gaz ortamında (%93 Ar - %7 H2 ve %100 H2) fırında sert lehimleme özellikleri araştırılmıştır. Çalışmada fırında sert lehimleme prosesi sırasında kullanılan farklı koruyucu gazların birleştirilmiş bölgenin yorulma dayanımı ile mikroyapı ve sertlik özelliklerine etkisi incelenmiştir. Ayrıca mikroyapı ve kırılma yüzeyleri üzerinden yapılan karakterizasyon çalışmaları, yorulma testi sonuçları ile karşılaştırılarak değerlendirilmiştir. Yorulma testleri sonucunda %93 Ar - %7 H2 koruyucu gaz altında 20.000 çevrimde σnom,max değeri 250 MPa iken, %100 H2 koruyucu gazı kullanıldığında bu değer 450 MPa’a yükseldiği belirlenmiştir.
- Open Access
- 21 June 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (2) , 639-651
Microstructure and Mechanical Properties of Dissimilar Resistance Spot Welded Zn-Coated DP800–TBF1180 Automotive Steels Using MFDC Technology
The use of advanced high-strength steel in the automotive industry is increasing in last decade. This is due to the restrictions to reduce fuel consumption and thereby decrease harmful carbon dioxide emissions. This paper aims to investigate welding properties of dissimilar resistance spot welded hot dip galvanized DP800–TBF1180 automotive steels using MFDC (Mid Frequency Direct Current) technology. LME crack occurrence due to the zinc coating was determined by magnetic particle test. The mechanical properties of welded joints were determined by tensile-shear, cross-tension and hardness measurements. The micro structural characterization was also performed in the weld zones of the joints. The appropriate welding parameter range were selected for welding processes by MFDC technology. Therefore, LME crack formation were not observed according to magnetic particle test. The highest strength was obtained as 17.60 kN and 5.51 kN by tensile-shear and cross tension tests, respectively with a welding current of 8 kA. In addition, a soft zone was found in the HAZ for both base metals. The hardness decrease in HAZ is more pronounced on the TBF1180 side. The soft zone hardness values of the sample S4 were approximately 330 HV, and the hardness values of the base material were measured in the range of 376-386 HV.
- 21 June 2024
- Published by Polish Academy of Sciences Chancellery in Archives of Metallurgy and Materials
- Vol. 69 (2) , 639-651
Open AccessMicrostructure and Mechanical Properties of Dissimilar Resistance Spot Welded Zn-Coated DP800–TBF1180 Automotive Steels Using MFDC Technology
The use of advanced high-strength steel in the automotive industry is increasing in last decade. This is due to the restrictions to reduce fuel consumption and thereby decrease harmful carbon dioxide emissions. This paper aims to investigate welding properties of dissimilar resistance spot welded hot dip galvanized DP800–TBF1180 automotive steels using MFDC (Mid Frequency Direct Current) technology. LME crack occurrence due to the zinc coating was determined by magnetic particle test. The mechanical properties of welded joints were determined by tensile-shear, cross-tension and hardness measurements. The micro structural characterization was also performed in the weld zones of the joints. The appropriate welding parameter range were selected for welding processes by MFDC technology. Therefore, LME crack formation were not observed according to magnetic particle test. The highest strength was obtained as 17.60 kN and 5.51 kN by tensile-shear and cross tension tests, respectively with a welding current of 8 kA. In addition, a soft zone was found in the HAZ for both base metals. The hardness decrease in HAZ is more pronounced on the TBF1180 side. The soft zone hardness values of the sample S4 were approximately 330 HV, and the hardness values of the base material were measured in the range of 376-386 HV.
- 29 November 2023
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 54 (11) , 1433-1443
Mechanical properties and corrosion behavior of similar/dissimilar resistance spot welded automotive aluminum alloys
Recently, usage of high strength aluminum alloys in automotive applications increase. The reasons for that increase are the light‐weight, high strength, good formability, weldability and corrosion resistance of the aluminum alloys to improve fuel economy as well as decreasing carbon dioxide emission. Automotive hybrid structures are commonly manufactured using dissimilar AA5000‐AA6000 joints to improve mechanical requirements and corrosion resistance of the parts. In this study, AA5754 H111‐AA6063 T4 materials were joined both similarly and dissimilarly by resistance spot welding method. Within the study, a mid‐frequency direct current technology was used instead of conventional alternative current technology. The welded zone was investigated by micro hardness measurements and microstructural characterization. Tensile‐shear and cross‐tension tests were performed. The welded zone of all welded specimens was subjected to salt spray corrosion test. A nugget pull‐out fracture mode was observed on the fracture surface of the all welded joints after tensile‐shear and cross‐tension tests. The lowest hardness values were measured from the weld metals for all welded joints. Porosity and inclusion were observed in the weld nugget with minor cracks in heat affected zone by optical microscope investigations.
- 29 November 2023
- Published by Wiley in Materialwissenschaft und Werkstofftechnik
- Vol. 54 (11) , 1433-1443
Mechanical properties and corrosion behavior of similar/dissimilar resistance spot welded automotive aluminum alloys
Recently, usage of high strength aluminum alloys in automotive applications increase. The reasons for that increase are the light‐weight, high strength, good formability, weldability and corrosion resistance of the aluminum alloys to improve fuel economy as well as decreasing carbon dioxide emission. Automotive hybrid structures are commonly manufactured using dissimilar AA5000‐AA6000 joints to improve mechanical requirements and corrosion resistance of the parts. In this study, AA5754 H111‐AA6063 T4 materials were joined both similarly and dissimilarly by resistance spot welding method. Within the study, a mid‐frequency direct current technology was used instead of conventional alternative current technology. The welded zone was investigated by micro hardness measurements and microstructural characterization. Tensile‐shear and cross‐tension tests were performed. The welded zone of all welded specimens was subjected to salt spray corrosion test. A nugget pull‐out fracture mode was observed on the fracture surface of the all welded joints after tensile‐shear and cross‐tension tests. The lowest hardness values were measured from the weld metals for all welded joints. Porosity and inclusion were observed in the weld nugget with minor cracks in heat affected zone by optical microscope investigations.
- 12 July 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 65 (9) , 1322-1335
Decarburization effects on high-cycle fatigue of uncoated press hardened steels
The decarburization layer can be detrimental and lead failures in press hardened steels. This work investigates the effect of decarburization layer on the fatigue crack origination and growth on press hardened parts of uncoated 22MnB5 steel. The decarburization layer was analyzed by light microscope, scanning electron microscope, and microhardness measurements. It was found that decarburization layer has two distinct zones indicating complete and partial decarburization. To understand the effect of decarburization on crack origination, high cycle fatigue tests were performed on samples from press hardened parts in decarburized and polished (nondecarburized) conditions. The results have shown that the fatigue performance of press hardened steels in polished condition outperforms the fatigue samples in decarburized condition. In fractographic investigations, it was seen that decarburization is not only responsible for crack origination but also affects crack propagation by having full and partial decarburization zones. The full decarburization zone was acted as surface crack origination source. In the partial decarburization zone, the crack propagation behavior was changed by a complex phase microstructure of bainite, ferrite, and martensite.
- 12 July 2023
- Published by Walter de Gruyter GmbH in Materials Testing
- Vol. 65 (9) , 1322-1335
Decarburization effects on high-cycle fatigue of uncoated press hardened steels
The decarburization layer can be detrimental and lead failures in press hardened steels. This work investigates the effect of decarburization layer on the fatigue crack origination and growth on press hardened parts of uncoated 22MnB5 steel. The decarburization layer was analyzed by light microscope, scanning electron microscope, and microhardness measurements. It was found that decarburization layer has two distinct zones indicating complete and partial decarburization. To understand the effect of decarburization on crack origination, high cycle fatigue tests were performed on samples from press hardened parts in decarburized and polished (nondecarburized) conditions. The results have shown that the fatigue performance of press hardened steels in polished condition outperforms the fatigue samples in decarburized condition. In fractographic investigations, it was seen that decarburization is not only responsible for crack origination but also affects crack propagation by having full and partial decarburization zones. The full decarburization zone was acted as surface crack origination source. In the partial decarburization zone, the crack propagation behavior was changed by a complex phase microstructure of bainite, ferrite, and martensite.
- 9 May 2023
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 76 (10) , 2691-2699
Effect of Tempering on Mechanical Properties and Ballistic Performance of Novel Armor Steel by Hot Stamping
- 9 May 2023
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 76 (10) , 2691-2699
Effect of Tempering on Mechanical Properties and Ballistic Performance of Novel Armor Steel by Hot Stamping
- Open Access
- 1 January 2023
- Published by TANGER Ltd.
Determination of Liquid Metal Embrittlement After Resistance Spot Welding of Zn-Coated High-Strength Steels
- 1 January 2023
- Published by TANGER Ltd.
Open AccessDetermination of Liquid Metal Embrittlement After Resistance Spot Welding of Zn-Coated High-Strength Steels
- Open Access
- 1 January 2023
- Published by TANGER Ltd.
Mechanical properties of AlSi10Mg Plates Produced by Selective Laser Melting with dissimilar automotive aluminum alloys by Friction Stir Welding
- 1 January 2023
- Published by TANGER Ltd.
Open AccessMechanical properties of AlSi10Mg Plates Produced by Selective Laser Melting with dissimilar automotive aluminum alloys by Friction Stir Welding
- Open Access
- 31 December 2022
- Published by ISRES Publishing in The Eurasia Proceedings of Science Technology Engineering and Mathematics
- Vol. 21, 79-87
New Trends in Aluminum Die Casting Alloys for Automotive Applications
In order to provide ecological balance, new technologies are being developed to reduce fuel consumption. Within these new technologies, usage of light alloys such as aluminum and magnesium has gained great importance in the automotive applications. The advantages of aluminum alloys in terms of light weight, recycling, machinability and corrosion resistance led to increase application area of these alloys. Due to these characteristics of aluminum alloys, fuel-saving light-weight material selection plays an important role for automotive parts. Aluminum applications increase not only in automotive, but also in aerospace, space shuttle, marine, and defense applications. According to the production methods, aluminum alloys are generally classified as casting, sheet, forging and extrusion. Aluminum die casting alloys are generally used the production of suspension systems, engines and gears parts. However, with the developing aluminum casting technologies, the aluminum die casting method makes it possible to manufacture multiple body parts in one piece. It is predicted that number of aluminum die casting parts will increase, especially in electric vehicles. In this study, the importance of the use of aluminum die casting alloys in the automotive industry is emphasized. Research and trends so far of the development of aluminum die casting alloys are also summarized.
- 31 December 2022
- Published by ISRES Publishing in The Eurasia Proceedings of Science Technology Engineering and Mathematics
- Vol. 21, 79-87
Open AccessNew Trends in Aluminum Die Casting Alloys for Automotive Applications
In order to provide ecological balance, new technologies are being developed to reduce fuel consumption. Within these new technologies, usage of light alloys such as aluminum and magnesium has gained great importance in the automotive applications. The advantages of aluminum alloys in terms of light weight, recycling, machinability and corrosion resistance led to increase application area of these alloys. Due to these characteristics of aluminum alloys, fuel-saving light-weight material selection plays an important role for automotive parts. Aluminum applications increase not only in automotive, but also in aerospace, space shuttle, marine, and defense applications. According to the production methods, aluminum alloys are generally classified as casting, sheet, forging and extrusion. Aluminum die casting alloys are generally used the production of suspension systems, engines and gears parts. However, with the developing aluminum casting technologies, the aluminum die casting method makes it possible to manufacture multiple body parts in one piece. It is predicted that number of aluminum die casting parts will increase, especially in electric vehicles. In this study, the importance of the use of aluminum die casting alloys in the automotive industry is emphasized. Research and trends so far of the development of aluminum die casting alloys are also summarized.
- 16 November 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 76 (1) , 49-57
Resistance Spot Welding of Zn-Coated Third Generation Automotive Steels Using Mid-Frequency Direct Current Technology
- 16 November 2022
- Published by Springer Nature in Transactions of the Indian Institute of Metals
- Vol. 76 (1) , 49-57
Resistance Spot Welding of Zn-Coated Third Generation Automotive Steels Using Mid-Frequency Direct Current Technology