Nazmul Islam Tanvir
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Nazmul Islam Tanvir has a total of 18 co-authors. Here are the top co-authors by number of shared publications:
- Syed Farid Uddin Farhad
Bangladesh Council of Scientific and Industrial Research (BCSIR)
4 shared publications - Mohammad Sajjad Hossain
Bnagladesh Council of Scientific & Industrial Research
2 shared publications - Nur Amin Bitu
Department of Chemistry, University of Rajshahi, Rajshahi, Bangladesh
2 shared publications - Suravi Islam
Institute of Glass & Ceramic Research and Testing, Bangladesh Council of Scientific and Industrial Research (BCSIR), Dhaka 1205, Bangladesh
2 shared publications A. S. M. Asadur Rahman
Department of Chemistry, Comilla University, Kotbari, Cumilla 3506, Bangladesh
1 shared publicationAftab Ali Shaikh
Bangladesh Council of Scientific and Industrial Research (BCSIR), Bangladesh
1 shared publication
Latest Publications
- 1 September 2023
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 12 (9) , 093006
Fabrication and Characterization of Graphene-Barium Titanate-Graphene Layered Capacitors by Spin Coating at Low Processing Temperatures
Barium titanate, BaTiO3 (BT), materials have been synthesized by two different routes. One ball-mill-derived (BMD) nanopowder and another precursor-derived (PCD) BT synthesis method were used separately to fabricate BT thin films on stainless steel (SS) and quartz substrates by spin coating. Then thin films from both synthesis routes were characterized by Ultraviolet-Visible-Near Infrared (UV–vis-NIR) Spectroscopy, Field-Emission Scanning Electron Microscopy (FE-SEM), X-ray Diffractometry (XRD), Raman Spectroscopy, and Four-point collinear probe; all carried out at room temperature. Our studies revealed that the PCD synthesis process did not produce the BT phase even under the 900 °C air-annealing condition. In contrast, a homogeneous BT thin film has been formed from the BMD-BT nanopowder. The optical bandgap of BMD-BT thin films was found in the 3.10–3.31 eV range. Finally, a Graphene-Barium Titanate-Graphene (G-BT-G) structure was fabricated on an SS substrate by spin coating at processing temperatures below 100 °C and characterized by two different pieces of equipment: a Potentiostat/Galvanostat (PG-STAT) and a Precision Impedance Analyzer (PIA). The G-BT-G structure exhibited a capacitance of 8 nF and 7.15 nF, a highest dielectric constant of 800 and 790, and a low dielectric loss of 4.5 and 5, investigated by PG-STAT and PIA equipment, respectively.
- 1 September 2023
- Published by The Electrochemical Society in ECS Journal of Solid State Science and Technology
- Vol. 12 (9) , 093006
Fabrication and Characterization of Graphene-Barium Titanate-Graphene Layered Capacitors by Spin Coating at Low Processing Temperatures
Barium titanate, BaTiO3 (BT), materials have been synthesized by two different routes. One ball-mill-derived (BMD) nanopowder and another precursor-derived (PCD) BT synthesis method were used separately to fabricate BT thin films on stainless steel (SS) and quartz substrates by spin coating. Then thin films from both synthesis routes were characterized by Ultraviolet-Visible-Near Infrared (UV–vis-NIR) Spectroscopy, Field-Emission Scanning Electron Microscopy (FE-SEM), X-ray Diffractometry (XRD), Raman Spectroscopy, and Four-point collinear probe; all carried out at room temperature. Our studies revealed that the PCD synthesis process did not produce the BT phase even under the 900 °C air-annealing condition. In contrast, a homogeneous BT thin film has been formed from the BMD-BT nanopowder. The optical bandgap of BMD-BT thin films was found in the 3.10–3.31 eV range. Finally, a Graphene-Barium Titanate-Graphene (G-BT-G) structure was fabricated on an SS substrate by spin coating at processing temperatures below 100 °C and characterized by two different pieces of equipment: a Potentiostat/Galvanostat (PG-STAT) and a Precision Impedance Analyzer (PIA). The G-BT-G structure exhibited a capacitance of 8 nF and 7.15 nF, a highest dielectric constant of 800 and 790, and a low dielectric loss of 4.5 and 5, investigated by PG-STAT and PIA equipment, respectively.
- 6 February 2023
- Published by Springer Nature in MRS Advances
- Vol. 8 (5) , 194-200
Effect of substrate surface on the wide bandgap SnO2 thin films grown by spin coating
- 6 February 2023
- Published by Springer Nature in MRS Advances
- Vol. 8 (5) , 194-200
Effect of substrate surface on the wide bandgap SnO2 thin films grown by spin coating
- Open Access
- 10 August 2022
- Published by The Royal Society in Royal Society Open Science
- Vol. 9 (8) , 220681
Facile extraction and characterization of calcium hydroxide from paper mill waste sludge of Bangladesh
Herein, paper mill waste sludge (PMS) from two different sources has been investigated to extract calcium hydroxide, Ca(OH) 2 by a facile and inexpensive extraction process. PMS samples, collected from local paper mill plants of Bangladesh, were the main precursors wherein HCl and NaOH were used for chemical treatment. The as-synthesized products were analysed by a variety of characterization tools including X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) elemental analyses. Our studies confirm that the extracted product contains Ca(OH) 2 as a major content, albeit it also includes CaCO 3 phase owing to the inescapable carbonation process from the surrounding environment. The particle size of the synthesized products is in the range of 450–500 nm estimated from SEM micrographs. The crystallite domain size of the same estimated from XRD analyses and was found to be approximately 47 and 31 nm respectively for product-A and product-B considering major (101) Bragg peak of Ca(OH) 2 . The yield percentage of the isolated products is about 65% for samples collected from both sources.
- 10 August 2022
- Published by The Royal Society in Royal Society Open Science
- Vol. 9 (8) , 220681
Open AccessFacile extraction and characterization of calcium hydroxide from paper mill waste sludge of Bangladesh
Herein, paper mill waste sludge (PMS) from two different sources has been investigated to extract calcium hydroxide, Ca(OH) 2 by a facile and inexpensive extraction process. PMS samples, collected from local paper mill plants of Bangladesh, were the main precursors wherein HCl and NaOH were used for chemical treatment. The as-synthesized products were analysed by a variety of characterization tools including X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectroscopy, Raman spectroscopy, scanning electron microscopy (SEM) and energy dispersive X-ray (EDX) elemental analyses. Our studies confirm that the extracted product contains Ca(OH) 2 as a major content, albeit it also includes CaCO 3 phase owing to the inescapable carbonation process from the surrounding environment. The particle size of the synthesized products is in the range of 450–500 nm estimated from SEM micrographs. The crystallite domain size of the same estimated from XRD analyses and was found to be approximately 47 and 31 nm respectively for product-A and product-B considering major (101) Bragg peak of Ca(OH) 2 . The yield percentage of the isolated products is about 65% for samples collected from both sources.
- Open Access
- 1 March 2019
- Published by Springer Nature in MRS Advances
- Vol. 4 (16) , 921-928
Synthesis and Characterization of c-Axis Oriented Zinc Oxide Thin Film and Its Use for the Subsequent Hydrothermal Growth of Zinc Oxide Nanorods
- 1 March 2019
- Published by Springer Nature in MRS Advances
- Vol. 4 (16) , 921-928
Open AccessSynthesis and Characterization of c-Axis Oriented Zinc Oxide Thin Film and Its Use for the Subsequent Hydrothermal Growth of Zinc Oxide Nanorods