Jun Xie
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Jun Xie has a total of 39 co-authors. Here are the top co-authors by number of shared publications:
- Dawei Chen
College of Safety and Environmental Engineering, Shandong University of Science and Technology, Qingdao, China
3 shared publications Yi Wang
Shandong University of Science and Technology
3 shared publicationsDawei Chen
Shandong University of Science and Technology
2 shared publicationsShurong Xu
Guizhou Qianxi Energy Development
2 shared publicationsAihua Yan
1 shared publicationChao Li
College of Mining and Safety Engineering, Shandong University of Science and Technology, Qingdao 266590, China
1 shared publication
Latest Publications
- 1 September 2026
- Published by Taylor & Francis in Combustion Science and Technology
- p. 1-24
Spontaneous Combustion Hazard Zoning and Ventilation Optimization in an Adjacent Goaf Considering Zonal Porosity of Narrow Coal Pillars
China’s energy structure has historically relied heavily on coal, which accounts for more than 50% of the country’s total primary energy consumption. As a key fossil fuel, coal serves as a crucial ...
- 1 September 2026
- Published by Taylor & Francis in Combustion Science and Technology
- p. 1-24
Spontaneous Combustion Hazard Zoning and Ventilation Optimization in an Adjacent Goaf Considering Zonal Porosity of Narrow Coal Pillars
China’s energy structure has historically relied heavily on coal, which accounts for more than 50% of the country’s total primary energy consumption. As a key fossil fuel, coal serves as a crucial ...
- Open Access
- 1 July 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (27) , 28932-28943
Research on Coal Mine Gas Microbial Degradation Device Based on Charcoal Filling Material
Microbiological methods are a new means of environmentally friendly and efficient methane treatment in coal mines. However, traditional microbial processes have a short action time and low degradation efficiency in local methane treatment. For this reason, a novel hierarchical enhanced contact microbial reaction apparatus (HECMRA) was designed and developed in this study. Charcoal with a particle size of 0.5–1 mm was selected as the optimal filler material for the reactor among the three porous media materials through experiments. Similar simulation experiments of the microbial reactor were carried out, and the results show that the reactor is well adapted to the mine environment, and the unit methane absorption can reach up to 14.213 μmol/cm3·h under the conditions of methane concentration of 1–10% and the temperature of 27–34 °C. The results of the research provide theoretical and technological references for the engineering problems of methane local accumulation in coal mines.
- 1 July 2025
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 10 (27) , 28932-28943
Open AccessResearch on Coal Mine Gas Microbial Degradation Device Based on Charcoal Filling Material
Microbiological methods are a new means of environmentally friendly and efficient methane treatment in coal mines. However, traditional microbial processes have a short action time and low degradation efficiency in local methane treatment. For this reason, a novel hierarchical enhanced contact microbial reaction apparatus (HECMRA) was designed and developed in this study. Charcoal with a particle size of 0.5–1 mm was selected as the optimal filler material for the reactor among the three porous media materials through experiments. Similar simulation experiments of the microbial reactor were carried out, and the results show that the reactor is well adapted to the mine environment, and the unit methane absorption can reach up to 14.213 μmol/cm3·h under the conditions of methane concentration of 1–10% and the temperature of 27–34 °C. The results of the research provide theoretical and technological references for the engineering problems of methane local accumulation in coal mines.
- Open Access
- 1 January 2025
- Published by Wiley in International Journal of Energy Research
- Vol. 2025 (1)
Investigating Enhanced Oil Recovery Techniques in Ultratight Reservoirs Through Coreflooding Experiments
This study explores the efficacy of various enhanced oil recovery (EOR) techniques, including water alternating gas (WAG), gas alternating water (GAW), alkaline surfactant polymer (ASP), and chemical WAG (CWAG) injections. Through coreflooding tests and analysis, we assess their effectiveness in mobilizing and displacing trapped oil in reservoirs. Our findings reveal significant novelty in the chemical methods developed, particularly in CWAG injection strategies, which achieved remarkable oil recovery factors. Specifically, WAG injection demonstrated superior performance, with a maximum oil recovery factor of 64.5%, attributable to water’s higher displacement efficiency. ASP injections also emerged as a promising method, achieving a maximum oil recovery factor of 69.5%, offering comparable recovery to traditional techniques while enhancing sweep efficiency. Furthermore, advanced CWAG injection strategies showcased significant improvements, with CWAG1, CWAG2, CWAG3, and CWAG4 achieving oil recovery factors of 73.5%, 76%, 82%, and 93%, respectively. These insights highlight the critical role of chemical formulation, injection sequence, and optimization techniques in maximizing oil recovery, thereby, contributing to sustainable resource management and economic viability.
- 1 January 2025
- Published by Wiley in International Journal of Energy Research
- Vol. 2025 (1)
Open AccessInvestigating Enhanced Oil Recovery Techniques in Ultratight Reservoirs Through Coreflooding Experiments
This study explores the efficacy of various enhanced oil recovery (EOR) techniques, including water alternating gas (WAG), gas alternating water (GAW), alkaline surfactant polymer (ASP), and chemical WAG (CWAG) injections. Through coreflooding tests and analysis, we assess their effectiveness in mobilizing and displacing trapped oil in reservoirs. Our findings reveal significant novelty in the chemical methods developed, particularly in CWAG injection strategies, which achieved remarkable oil recovery factors. Specifically, WAG injection demonstrated superior performance, with a maximum oil recovery factor of 64.5%, attributable to water’s higher displacement efficiency. ASP injections also emerged as a promising method, achieving a maximum oil recovery factor of 69.5%, offering comparable recovery to traditional techniques while enhancing sweep efficiency. Furthermore, advanced CWAG injection strategies showcased significant improvements, with CWAG1, CWAG2, CWAG3, and CWAG4 achieving oil recovery factors of 73.5%, 76%, 82%, and 93%, respectively. These insights highlight the critical role of chemical formulation, injection sequence, and optimization techniques in maximizing oil recovery, thereby, contributing to sustainable resource management and economic viability.
- 8 July 2024
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 9 (9) , 2489-2504
Experimental study on the leaching effect of different chelating agents on the constant metal ions of lignite
Chelating agents can increase the porosity of coal by leaching metal ions from it. Therefore, selecting the most suitable chelating agent based on the characteristics of the coal type is crucial when applying chelating agents. In this study, lignite from southwest China was chosen as the sample. Four chelating agents, namely tetrasodium iminodisuccinate (IDS), diethylenetriaminepentaacetic acid (DTPA), tetrasodium aspartate diacetate (ASDA), and tetrasodium glutamate diacetate (GLDA), were evaluated for their impact on the leaching of constant metal ions (CMIs). The leaching effect of CMIs was characterized and analyzed using inductively coupled plasma, scanning electron microscopy, and Brunauer–Emmett–Teller measurements. The results indicated that the ASDA chelating agent was the most effective in leaching Ca2+, Mg2+, Fe2+/3+, and Al3+. Under the optimal concentration condition of 2500 mg L−1, the leaching effect of CMIs from different chelating agents could be ranked as: ASDA > DTPA > IDS > GLDA. The contact angle of the ASDA chelating agent with the coal sample decreased from 48.2° at 1 s to 26.5° at 20 s. The metal minerals on the surface of the coal dissolved under the action of the ASDA chelating agent, and the micropores on the coal surface transitioned to mesopores and macropores. The pore volume of coal samples increased from 0.0254 cm3 g−1 to 0.0276 cm3 g−1, and the pore size increased from 3.26 nm to 4.06 nm. As the pore size of the coal increased, the permeability also significantly increased.
- 8 July 2024
- Published by Royal Society of Chemistry (RSC) in Reaction Chemistry & Engineering
- Vol. 9 (9) , 2489-2504
Experimental study on the leaching effect of different chelating agents on the constant metal ions of lignite
Chelating agents can increase the porosity of coal by leaching metal ions from it. Therefore, selecting the most suitable chelating agent based on the characteristics of the coal type is crucial when applying chelating agents. In this study, lignite from southwest China was chosen as the sample. Four chelating agents, namely tetrasodium iminodisuccinate (IDS), diethylenetriaminepentaacetic acid (DTPA), tetrasodium aspartate diacetate (ASDA), and tetrasodium glutamate diacetate (GLDA), were evaluated for their impact on the leaching of constant metal ions (CMIs). The leaching effect of CMIs was characterized and analyzed using inductively coupled plasma, scanning electron microscopy, and Brunauer–Emmett–Teller measurements. The results indicated that the ASDA chelating agent was the most effective in leaching Ca2+, Mg2+, Fe2+/3+, and Al3+. Under the optimal concentration condition of 2500 mg L−1, the leaching effect of CMIs from different chelating agents could be ranked as: ASDA > DTPA > IDS > GLDA. The contact angle of the ASDA chelating agent with the coal sample decreased from 48.2° at 1 s to 26.5° at 20 s. The metal minerals on the surface of the coal dissolved under the action of the ASDA chelating agent, and the micropores on the coal surface transitioned to mesopores and macropores. The pore volume of coal samples increased from 0.0254 cm3 g−1 to 0.0276 cm3 g−1, and the pore size increased from 3.26 nm to 4.06 nm. As the pore size of the coal increased, the permeability also significantly increased.
- 1 September 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (45) , 101709-101724
Research on gas hazard prevention and control of a high-gas fully mechanized mining face based on ventilation system optimization
The gas accumulation in the return corner of a high-gas fully mechanized mining face can easily cause the gas volume fraction to exceed the safety limit, threatening the safety of coal mines. In this study, the unit method was used to analyze the gas sources and emissions based on the actual case. The airflow and gas distribution characteristics of the two-inlet-one-outlet (TIOO) ventilation system and the one-inlet-two-outlet (OITO) ventilation system were studied using CFD numerical simulation. The results show that under the TIOO ventilation system, the “U”-type air leakage in the goaf leads deep gas into the return corner, which causes the gas volume fraction in the return corner to rise to 0.4–2.0%. After the mining face is optimized into the OITO ventilation system, the “J”-type air leakage of the goaf suppresses the high concentration of gas in the deep position of the goaf. Combined with the gas extraction measures, the gas volume fraction in the return corner, exhaust roadway’s outlet, and retaining roadway’s outlet is controlled at 0.28%, 0.34%, and 0.23%. This study will provide new ideas for solving the problem of gas accumulation in the return corner of a high-gas fully mechanized mining face.
- 1 September 2023
- Published by Springer Nature in Environmental Science and Pollution Research
- Vol. 30 (45) , 101709-101724
Research on gas hazard prevention and control of a high-gas fully mechanized mining face based on ventilation system optimization
The gas accumulation in the return corner of a high-gas fully mechanized mining face can easily cause the gas volume fraction to exceed the safety limit, threatening the safety of coal mines. In this study, the unit method was used to analyze the gas sources and emissions based on the actual case. The airflow and gas distribution characteristics of the two-inlet-one-outlet (TIOO) ventilation system and the one-inlet-two-outlet (OITO) ventilation system were studied using CFD numerical simulation. The results show that under the TIOO ventilation system, the “U”-type air leakage in the goaf leads deep gas into the return corner, which causes the gas volume fraction in the return corner to rise to 0.4–2.0%. After the mining face is optimized into the OITO ventilation system, the “J”-type air leakage of the goaf suppresses the high concentration of gas in the deep position of the goaf. Combined with the gas extraction measures, the gas volume fraction in the return corner, exhaust roadway’s outlet, and retaining roadway’s outlet is controlled at 0.28%, 0.34%, and 0.23%. This study will provide new ideas for solving the problem of gas accumulation in the return corner of a high-gas fully mechanized mining face.
- Open Access
- 5 August 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (32) , 27991-28002
Study on the Mechanics and Pore Characteristics of Coal Seam Drilling Sealing Materials Based on Nanomaterial Optimization
In order to modify and optimize the performance of cement-based sealing materials and improve the gas drainage rate of boreholes. In this paper, nanosilica (NS), multiwalled carbon nanotubes (MWCNT), and graphene oxide (GO) were used to modify cement and optimize the pore structure. Uniaxial compression tests, X-ray diffraction (XRD), nuclear magnetic resonance (NMR), and combined fractal theory were used to analyze the mechanics and pore characteristics. The results show that the synergy of the three nanomaterials promotes the generation of hydration products such as calcium silicate hydrate (C-S-H) and ettringite (AFt), improves the total pore fractal dimension (Dw) and seepage pore fractal dimension (Ds), and optimizes the microscopic pore structure. However, when the content of NS increases from 2 to 4 wt %, the improvement in the mechanical properties is obviously weakened. The best ratio is where the SiO2 content is 2 wt %, the MWCNT content is 0.1 wt %, and the GO content is 0.03 wt %. Compared with pure cement, the fractal dimension increases significantly, the mechanical properties are increased by 24.7%, and the total porosity is reduced by 23.9%. This paper is of great significance for improving the efficiency of gas mining.
- 5 August 2022
- Published by American Chemical Society (ACS) in ACS Omega
- Vol. 7 (32) , 27991-28002
Open AccessStudy on the Mechanics and Pore Characteristics of Coal Seam Drilling Sealing Materials Based on Nanomaterial Optimization
In order to modify and optimize the performance of cement-based sealing materials and improve the gas drainage rate of boreholes. In this paper, nanosilica (NS), multiwalled carbon nanotubes (MWCNT), and graphene oxide (GO) were used to modify cement and optimize the pore structure. Uniaxial compression tests, X-ray diffraction (XRD), nuclear magnetic resonance (NMR), and combined fractal theory were used to analyze the mechanics and pore characteristics. The results show that the synergy of the three nanomaterials promotes the generation of hydration products such as calcium silicate hydrate (C-S-H) and ettringite (AFt), improves the total pore fractal dimension (Dw) and seepage pore fractal dimension (Ds), and optimizes the microscopic pore structure. However, when the content of NS increases from 2 to 4 wt %, the improvement in the mechanical properties is obviously weakened. The best ratio is where the SiO2 content is 2 wt %, the MWCNT content is 0.1 wt %, and the GO content is 0.03 wt %. Compared with pure cement, the fractal dimension increases significantly, the mechanical properties are increased by 24.7%, and the total porosity is reduced by 23.9%. This paper is of great significance for improving the efficiency of gas mining.
- Open Access
- 15 April 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (8) , 3550
Influence of Mix Proportions on Rheological Properties, Air Content of Wet Shotcrete—A Case Study
To study the influence of different mix proportions on the fresh properties of wet shotcrete, the rheological properties and air content of wet shotcrete with different admixtures before pumping were measured. In addition, the pressure drop along the pipeline and the build-up thickness were studied, and the relationship between the rheological properties and the pumpability and sprayability was discussed. This paper attempts to reveal the influence mechanism of admixtures on the fluidity of wet shotcrete by means of pictures. The results show that free paste effect and ball effect are two key factors that affect the performance of fresh wet shotcrete. Air-entraining agent and fly ash are commonly used admixtures, which improve the pumping performance and spraying performance. Finally, the mix proportions of wet shotcrete are put forward to meet the requirements of different types of shotcrete.
- 15 April 2021
- Published by MDPI AG in Applied Sciences
- Vol. 11 (8) , 3550
Open AccessInfluence of Mix Proportions on Rheological Properties, Air Content of Wet Shotcrete—A Case Study
To study the influence of different mix proportions on the fresh properties of wet shotcrete, the rheological properties and air content of wet shotcrete with different admixtures before pumping were measured. In addition, the pressure drop along the pipeline and the build-up thickness were studied, and the relationship between the rheological properties and the pumpability and sprayability was discussed. This paper attempts to reveal the influence mechanism of admixtures on the fluidity of wet shotcrete by means of pictures. The results show that free paste effect and ball effect are two key factors that affect the performance of fresh wet shotcrete. Air-entraining agent and fly ash are commonly used admixtures, which improve the pumping performance and spraying performance. Finally, the mix proportions of wet shotcrete are put forward to meet the requirements of different types of shotcrete.
- 7 January 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 142 (6) , 1-12
Simulation of Cavity Extension Formation in the Early Ignition Stage Based on a Coal Block Gasification Experiment
Underground coal gasification (UCG) is a highly efficient new type of coal mining technology with broad future prospects. In order to study the cavity extension formation in the early ignition stage of UCG, a block coal scale UCG simulation experiment was carried out. The results show that after the ignition, the temperature above ignition point rose fastest, and the coal combustion interface and high temperature area moved toward to the above of ignition point, while the temperature of the left and right sides of ignition point rose a little slowly. According to the results of dissected block coal, it is indicated that the extension scale in the vertical direction was significantly larger than other directions; the combustion cavity form was an irregular rectangle like a pear. The results of this experiment revealed the cavity extension process from ignition of UCG channels to the formation of cavity, which provided a foundation for the study of extension characteristics of UCG channel in the entire UCG process.
- 7 January 2020
- Published by Wiley in Journal of Energy Resources Technology
- Vol. 142 (6) , 1-12
Simulation of Cavity Extension Formation in the Early Ignition Stage Based on a Coal Block Gasification Experiment
Underground coal gasification (UCG) is a highly efficient new type of coal mining technology with broad future prospects. In order to study the cavity extension formation in the early ignition stage of UCG, a block coal scale UCG simulation experiment was carried out. The results show that after the ignition, the temperature above ignition point rose fastest, and the coal combustion interface and high temperature area moved toward to the above of ignition point, while the temperature of the left and right sides of ignition point rose a little slowly. According to the results of dissected block coal, it is indicated that the extension scale in the vertical direction was significantly larger than other directions; the combustion cavity form was an irregular rectangle like a pear. The results of this experiment revealed the cavity extension process from ignition of UCG channels to the formation of cavity, which provided a foundation for the study of extension characteristics of UCG channel in the entire UCG process.
- 7 February 2019
- Published by Springer Nature
- p. 159-162
Sedimentary Characteristics of the Fourth Member of Cretaceous Nenjiang Formation in the Southern Songliao Basin, Northeast of China
- 7 February 2019
- Published by Springer Nature
- p. 159-162
Sedimentary Characteristics of the Fourth Member of Cretaceous Nenjiang Formation in the Southern Songliao Basin, Northeast of China