Hiroyuki Kawata
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Hiroyuki Kawata has a total of 56 co-authors. Here are the top co-authors by number of shared publications:
Kenta Sakaguchi
Kurami Works, JX Nippon Mining & Metals Corporation
3 shared publications- Manabu Takahashi
Faculty of Engineering Sciences, Kyushu University
3 shared publications - Satoshi Okayama
Nara Medical University
3 shared publications Shigeto Yamasaki
Faculty of Engineering, Kyushu University
3 shared publications- Yoshihiko Saito
Department of Cardiovascular Medicine, Nara Medical University, Nara, Japan
3 shared publications - Ayako Seno
Department of Cardiovascular Medicine Nara Medical University Kashihara Japan
2 shared publications
Latest Publications
- Open Access
- 30 March 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (4) , 489-496
Characteristics of Strain Distribution in Grains Generating Grain Boundary Sliding through High-temperature Tensile Deformation in Carbon Steel
The strength at 600 °C in fire-resistant steel exhibits a significant dependence on strain rate, likely attributed to a shift in deformation mechanism from slip deformation to grain boundary sliding (GBS) with increasing temperature. In this study, GBS was observed using a grid method, and the strain distribution introduced by a high-temperature tensile test in a carbon steel was visualized. The characteristics of the strain distribution in the grains composing the grain boundary where GBS occurred were discussed. Although the test temperature was 500 °C, high-temperature tensile tests with strain rates of 10-3 and 10-5 s-1 orders were successfully conducted. Strain rate dependence of strength was comparably small at 500 °C. The discontinuous slide of the grid line at the grain boundary was observed after the tensile tests at 500 °C, regardless of strain rate, indicating that GBS occurred. The strain was distributed inhomogeneously during the high-temperature tensile tests. The grain boundary generating GBS lay 45 ° from the tensile direction and consisted of a pair of high- and low-strain grains. The m' value, which represents the ease of slip transfer between adjacent grains, was low at the grain boundaries generating GBS. This suggests that GBS was induced by pile-up dislocations at the grain boundary.
- 30 March 2026
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 66 (4) , 489-496
Open AccessCharacteristics of Strain Distribution in Grains Generating Grain Boundary Sliding through High-temperature Tensile Deformation in Carbon Steel
The strength at 600 °C in fire-resistant steel exhibits a significant dependence on strain rate, likely attributed to a shift in deformation mechanism from slip deformation to grain boundary sliding (GBS) with increasing temperature. In this study, GBS was observed using a grid method, and the strain distribution introduced by a high-temperature tensile test in a carbon steel was visualized. The characteristics of the strain distribution in the grains composing the grain boundary where GBS occurred were discussed. Although the test temperature was 500 °C, high-temperature tensile tests with strain rates of 10-3 and 10-5 s-1 orders were successfully conducted. Strain rate dependence of strength was comparably small at 500 °C. The discontinuous slide of the grid line at the grain boundary was observed after the tensile tests at 500 °C, regardless of strain rate, indicating that GBS occurred. The strain was distributed inhomogeneously during the high-temperature tensile tests. The grain boundary generating GBS lay 45 ° from the tensile direction and consisted of a pair of high- and low-strain grains. The m' value, which represents the ease of slip transfer between adjacent grains, was low at the grain boundaries generating GBS. This suggests that GBS was induced by pile-up dislocations at the grain boundary.
- Open Access
- 15 February 2024
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 110 (3) , 90-100
Bridging between Heterogeneous Local Strain Distribution and Macroscopic Stress-strain Curves
A modified continuum composite model was utilized to analyze the stress–strain behavior of as-quenched steels with a fully martensitic microstructure. The model was employed to express the stress–strain curves obtained by a simple tensile test and those obtained by forward and backward loading using a simple shear test machine. The study confirmed that the model can represent the stress–strain behavior under both forward and backward deformation. In addition, the evolution of local strain distributions during plastic deformation was investigated using a digital image correlation method. The strain distributions and their evolution during deformation were qualitatively represented using this model. The discrepancies between the model calculations and experiments are due to the limitations of the iso-work assumption and the impact of slip deformation on the macroscopic work-hardening behavior of martensitic steels. Highly strain-concentrated regions aligned along the longitudinal direction of the lath and block, known as in-lath-plane slips, may not play an important role in the work-hardening behavior of as-quenched martensitic steels. However, the other slips, namely the out-of-lath slip, may play a significant role in the work hardening of as-quenched martensitic steels.
- 15 February 2024
- Published by Iron and Steel Institute of Japan in Tetsu-to-Hagane
- Vol. 110 (3) , 90-100
Open AccessBridging between Heterogeneous Local Strain Distribution and Macroscopic Stress-strain Curves
A modified continuum composite model was utilized to analyze the stress–strain behavior of as-quenched steels with a fully martensitic microstructure. The model was employed to express the stress–strain curves obtained by a simple tensile test and those obtained by forward and backward loading using a simple shear test machine. The study confirmed that the model can represent the stress–strain behavior under both forward and backward deformation. In addition, the evolution of local strain distributions during plastic deformation was investigated using a digital image correlation method. The strain distributions and their evolution during deformation were qualitatively represented using this model. The discrepancies between the model calculations and experiments are due to the limitations of the iso-work assumption and the impact of slip deformation on the macroscopic work-hardening behavior of martensitic steels. Highly strain-concentrated regions aligned along the longitudinal direction of the lath and block, known as in-lath-plane slips, may not play an important role in the work-hardening behavior of as-quenched martensitic steels. However, the other slips, namely the out-of-lath slip, may play a significant role in the work hardening of as-quenched martensitic steels.
- Open Access
- 30 January 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (2) , 202-211
Geometry of Butterfly Martensite in Fe-18Ni-0.7Cr-0.5C Alloy
To clarify the geometry of the junction of martensite which forming butterfly-type martensite, electron microscopy, theoretical analysis using the phenomenological theory of martensite crystallography and rank-1 connection were carried out on Fe-18Ni-0.7Cr-0.5C (mass %) alloy. Martensite plates in this alloy exhibit {252}𝛾 habit plane and K-S OR and are in good agreement with the double shear PTMC by Ross and Crocker. The frequency of formation of V1/V2 and V1/V16 (butterflies) pairs was 20% each, with these two pairs alone accounting for 40% of the total. Theoretical analysis using rank-1 connection of variants revealed that butterfly-pairing is not a geometrically compatible morphology, even for alloys in which butterfly martensite forms frequently. We have also revealed theoretically that the junction plane of the butterfly-pairing keeps (100)𝛾 independent of the mode of lattice invariant shear (i.e. morphology of martensite plate). Preferential formation mechanism for butterfly-pairing is discussed based on the common lattice invariant deformation between V1 and V16.
- 30 January 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (2) , 202-211
Open AccessGeometry of Butterfly Martensite in Fe-18Ni-0.7Cr-0.5C Alloy
To clarify the geometry of the junction of martensite which forming butterfly-type martensite, electron microscopy, theoretical analysis using the phenomenological theory of martensite crystallography and rank-1 connection were carried out on Fe-18Ni-0.7Cr-0.5C (mass %) alloy. Martensite plates in this alloy exhibit {252}𝛾 habit plane and K-S OR and are in good agreement with the double shear PTMC by Ross and Crocker. The frequency of formation of V1/V2 and V1/V16 (butterflies) pairs was 20% each, with these two pairs alone accounting for 40% of the total. Theoretical analysis using rank-1 connection of variants revealed that butterfly-pairing is not a geometrically compatible morphology, even for alloys in which butterfly martensite forms frequently. We have also revealed theoretically that the junction plane of the butterfly-pairing keeps (100)𝛾 independent of the mode of lattice invariant shear (i.e. morphology of martensite plate). Preferential formation mechanism for butterfly-pairing is discussed based on the common lattice invariant deformation between V1 and V16.
- Open Access
- 30 January 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (2) , 345-353
Bridging between Heterogeneous Local Strain Distribution and Macroscopic Stress-strain Curves
A modified continuum composite model was utilized to analyze the stress–strain behavior of as-quenched steels with a fully martensitic microstructure. The model was employed to express the stress–strain curves obtained by a simple tensile test and those obtained by forward and backward loading using a simple shear test machine. The study confirmed that the model can represent the stress–strain behavior under both forward and backward deformation. In addition, the evolution of local strain distributions during plastic deformation was investigated using a digital image correlation method. The strain distributions and their evolution during deformation were qualitatively represented using this model. The discrepancies between the model calculations and experiments are due to the limitations of the iso-work assumption and the impact of slip deformation on the macroscopic work-hardening behavior of martensitic steels. Highly strain-concentrated regions aligned along the longitudinal direction of the lath and block, known as in-lath-plane slips, may not play an important role in the work-hardening behavior of as-quenched martensitic steels. However, the other slips, namely the out-of-lath slip, may play a significant role in the work hardening of as-quenched martensitic steels.
- 30 January 2024
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 64 (2) , 345-353
Open AccessBridging between Heterogeneous Local Strain Distribution and Macroscopic Stress-strain Curves
A modified continuum composite model was utilized to analyze the stress–strain behavior of as-quenched steels with a fully martensitic microstructure. The model was employed to express the stress–strain curves obtained by a simple tensile test and those obtained by forward and backward loading using a simple shear test machine. The study confirmed that the model can represent the stress–strain behavior under both forward and backward deformation. In addition, the evolution of local strain distributions during plastic deformation was investigated using a digital image correlation method. The strain distributions and their evolution during deformation were qualitatively represented using this model. The discrepancies between the model calculations and experiments are due to the limitations of the iso-work assumption and the impact of slip deformation on the macroscopic work-hardening behavior of martensitic steels. Highly strain-concentrated regions aligned along the longitudinal direction of the lath and block, known as in-lath-plane slips, may not play an important role in the work-hardening behavior of as-quenched martensitic steels. However, the other slips, namely the out-of-lath slip, may play a significant role in the work hardening of as-quenched martensitic steels.
- Open Access
- 15 December 2023
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 63 (12) , 2066-2077
Modeling of Loading-path Dependent Martensitic Transformation in a Low-alloy TRIP Steel
The aim of this paper is to predict the deformation-induced martensitic transformation of the retained austenite in steels under various deformations, including loading-path changes, by using mesoscopic finite element analyses (FEAs). First, a TRIP steel was subjected to monotonic uniaxial tension and compression, as well as a couple of two-stage loadings to investigate the effect of loading direction and loading-path on transformation behavior experimentally. In monotonic loading, tension induced transformation at higher rate than compression did. Whereas, in two-stage loadings, the transformation progress was suspended immediately after the start of secondary loading. As the secondary tension proceeded, the transformation resumed and gradually accelerated toward the transformation rate for monotonic tension. These experimental results were analyzed by FEAs with a two-dimensional image of microstructure. The transformation rates under monotonic loading are well predicted by the simulation. It is also suggested that the difference in the transformation rate between tension and compression is mainly due to the volumetric expansion associated with martensitic transformation, and that the transformation behavior of the untransformed austenite is dominated by the distribution of the hard transformed martensite. In addition, the prediction of the transformation rate in secondary tension after pre-compression required the consideration of back stress in the austenite. The reproducibility of the transformation behavior just after the onset of secondary deformation was improved by the hypothesis that the equivalent value of back stress tensor at the transformation needs to exceed its maximum value in the past.
- 15 December 2023
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 63 (12) , 2066-2077
Open AccessModeling of Loading-path Dependent Martensitic Transformation in a Low-alloy TRIP Steel
The aim of this paper is to predict the deformation-induced martensitic transformation of the retained austenite in steels under various deformations, including loading-path changes, by using mesoscopic finite element analyses (FEAs). First, a TRIP steel was subjected to monotonic uniaxial tension and compression, as well as a couple of two-stage loadings to investigate the effect of loading direction and loading-path on transformation behavior experimentally. In monotonic loading, tension induced transformation at higher rate than compression did. Whereas, in two-stage loadings, the transformation progress was suspended immediately after the start of secondary loading. As the secondary tension proceeded, the transformation resumed and gradually accelerated toward the transformation rate for monotonic tension. These experimental results were analyzed by FEAs with a two-dimensional image of microstructure. The transformation rates under monotonic loading are well predicted by the simulation. It is also suggested that the difference in the transformation rate between tension and compression is mainly due to the volumetric expansion associated with martensitic transformation, and that the transformation behavior of the untransformed austenite is dominated by the distribution of the hard transformed martensite. In addition, the prediction of the transformation rate in secondary tension after pre-compression required the consideration of back stress in the austenite. The reproducibility of the transformation behavior just after the onset of secondary deformation was improved by the hypothesis that the equivalent value of back stress tensor at the transformation needs to exceed its maximum value in the past.
- Open Access
- 15 October 2022
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 62 (10) , 2008-2015
Microstructural Size Effect on Strain-Hardening of As-Quenched Low-Alloyed Martensitic Steels
Quenched martensitic steels are known to show the characteristic feature of stress–strain relations, with extremely low elastic limits and very large work-hardening. The continuum composite approach is one way to express this characteristic feature of stress–strain curves. Although the overall stress–strain curves, as a function of alloy chemistries of steels, were well represented by this approach, the relationship between the macroscopic deformation behaviors and microstructural information is yet to be clarified. A high-spatial-resolution digital image correlation analysis was conducted to demonstrate the possible unit size corresponding to the microstructure. The continuum composite approach model was also modified to consider the size effect of the microstructure on the stress–strain curves of the as-quenched martensitic steels. Strain concentrations were observed at various boundaries, including lath boundaries, and the characteristic microstructural size was also predicted by the present model, which is smaller than the reported spacing between adjacent strain-concentrated regions.
- 15 October 2022
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 62 (10) , 2008-2015
Open AccessMicrostructural Size Effect on Strain-Hardening of As-Quenched Low-Alloyed Martensitic Steels
Quenched martensitic steels are known to show the characteristic feature of stress–strain relations, with extremely low elastic limits and very large work-hardening. The continuum composite approach is one way to express this characteristic feature of stress–strain curves. Although the overall stress–strain curves, as a function of alloy chemistries of steels, were well represented by this approach, the relationship between the macroscopic deformation behaviors and microstructural information is yet to be clarified. A high-spatial-resolution digital image correlation analysis was conducted to demonstrate the possible unit size corresponding to the microstructure. The continuum composite approach model was also modified to consider the size effect of the microstructure on the stress–strain curves of the as-quenched martensitic steels. Strain concentrations were observed at various boundaries, including lath boundaries, and the characteristic microstructural size was also predicted by the present model, which is smaller than the reported spacing between adjacent strain-concentrated regions.
- Open Access
- 12 August 2022
- Published by Elsevier in Forces in Mechanics
- Vol. 9
Mesoscopic numerical study on ductile fracture in TRIP steel under reverse loading
- 12 August 2022
- Published by Elsevier in Forces in Mechanics
- Vol. 9
Open AccessMesoscopic numerical study on ductile fracture in TRIP steel under reverse loading
- Open Access
- 15 July 2019
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 59 (7) , 1344-1353
Effect of Pearlite Volume Fraction on Two-step Ductile to Brittle Transition in Ferrite + Pearlite Structure Steel Sheets
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies
- 15 July 2019
- Published by Iron and Steel Institute of Japan in ISIJ International
- Vol. 59 (7) , 1344-1353
Open AccessEffect of Pearlite Volume Fraction on Two-step Ductile to Brittle Transition in Ferrite + Pearlite Structure Steel Sheets
Japan's largest platform for academic e-journals: J-STAGE is a full text database for reviewed academic papers published by Japanese societies
- 27 February 2019
- Published by Springer Nature
- p. 529-535
Effect of Carbon Content on Strengthening Behavior with Grain Refinement on Lath Martensite Structure
- 27 February 2019
- Published by Springer Nature
- p. 529-535
Effect of Carbon Content on Strengthening Behavior with Grain Refinement on Lath Martensite Structure
- 12 April 2018
- Published by Springer Nature
- p. 143-147
Effect of Carbon Content on Bainite Transformation Start Temperature on Fe–9Ni–C Alloys
- 12 April 2018
- Published by Springer Nature
- p. 143-147
Effect of Carbon Content on Bainite Transformation Start Temperature on Fe–9Ni–C Alloys