Андрей Дмитриевич Зеленин
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Андрей Дмитриевич Зеленин has a total of 31 co-authors. Here are the top co-authors by number of shared publications:
- Nariman R. Memetov
Tambov State Technical University
7 shared publications - Alexander V. Babkin
Department of Chemistry, Lomonosov Moscow State University
4 shared publications - Alyona V. Gerasimova
Tambov State Technical University, Tambov, Russia
4 shared publications - Ananstasia Kucherova
Tambov State Technical University, Tambov, Russia
2 shared publications Anastasia Memetova
2 shared publications- Elena Neskoromnaya
Tambov State Tech Univ, Tambov, Russia
2 shared publications
Latest Publications
- Open Access
- 12 July 2026
- Published by Tambov State Technical University in Image Journal of Advanced Materials and Technologies
- Vol. 11 (2) , 162-171
Synthesis and study of the porous structure of biochars obtained from crustacean waste
Biochar samples from crustacean processing waste were synthesized by carbonization followed by alkaline activation. The influence of synthesis parameters (time, temperature) on the porous structure of biochar was considered. The results showed that biomass carbonization conditions significantly affect the final porosity parameters. It was found that the biochar samples obtained by varying the synthesis parameters were micromesoporous. Temperature was shown to be the main influencing factor during biomass carbonization. At a three-hour carbonization duration and a temperature of 650 °C, the specific surface area (2708 m 2 ×g –1 ) and pore volume (total pore – 1.58 cm 3 ×g –1 , micropore – 0.64 cm 3 ×g –1 , mesopore – 0.94 cm 3 ×g –1 ) in the obtained biochar reached their maximum values. Methane adsorption on the obtained biochar was studied at ambient temperature and pressure up to 100 bar. Biochar obtained from crustacean waste was shown to exhibit a high methane adsorption capacity of ~18 mmol×g –1 . Experimental adsorption data were analyzed using the Langmuir, Freundlich, and Dubinin-Radushkevich models. The influence of synthesis parameters on the pore structure of biochars, as well as the adsorption data evaluated in the study, are useful for designing adsorption systems.
- 12 July 2026
- Published by Tambov State Technical University in Image Journal of Advanced Materials and Technologies
- Vol. 11 (2) , 162-171
Open AccessSynthesis and study of the porous structure of biochars obtained from crustacean waste
Biochar samples from crustacean processing waste were synthesized by carbonization followed by alkaline activation. The influence of synthesis parameters (time, temperature) on the porous structure of biochar was considered. The results showed that biomass carbonization conditions significantly affect the final porosity parameters. It was found that the biochar samples obtained by varying the synthesis parameters were micromesoporous. Temperature was shown to be the main influencing factor during biomass carbonization. At a three-hour carbonization duration and a temperature of 650 °C, the specific surface area (2708 m 2 ×g –1 ) and pore volume (total pore – 1.58 cm 3 ×g –1 , micropore – 0.64 cm 3 ×g –1 , mesopore – 0.94 cm 3 ×g –1 ) in the obtained biochar reached their maximum values. Methane adsorption on the obtained biochar was studied at ambient temperature and pressure up to 100 bar. Biochar obtained from crustacean waste was shown to exhibit a high methane adsorption capacity of ~18 mmol×g –1 . Experimental adsorption data were analyzed using the Langmuir, Freundlich, and Dubinin-Radushkevich models. The influence of synthesis parameters on the pore structure of biochars, as well as the adsorption data evaluated in the study, are useful for designing adsorption systems.
- Open Access
- 1 January 2023
- Published by Togliatti State University in Frontier materials & technologies
- No. 2,p. 131-139
Electrically conductive nanocomposite bituminous binders containing carbon nanotubes and multilayer graphene
В современной литературе практически отсутствуют данные об электрических характеристиках битумных вяжущих, модифицированных углеродными нанотрубками и графеновыми нанопластинками, между тем как они необходимы для проектирования и разработки инновационных составов асфальтовых покрытий, восприимчивых к сверхвысокочастотному микроволновому излучению. Современные битумные вяжущие представляют собой многокомпонентные системы, которые могут содержать полимеры, каучуки, синтетические или природные смолы, неорганические соли и даже ароматизаторы. В результате применения модифицирующих добавок битум приобретает высокие эксплуатационные характеристики. Особый класс модификаторов составляют микро- и наноразмерные электропроводящие волокна и частицы (стальная вата, углеродные волокна, технический углерод, углеродные нанотрубки, графеновые нанопластинки), применение которых позволяет обеспечивать восприимчивость битумных вяжущих к сверхвысокочастотному микроволновому излучению и реализацию процесса залечивания трещин в асфальтовом покрытии с его последующей регенерацией. В рамках исследования разработана оригинальная методика получения битумных вяжущих, модифицированных углеродными нанотрубками и многослойным графеном. Экспериментально получены модифицированные битумные составы в диапазоне концентраций от 0,2 до 6 и от 0,2 до 11 масс. % для многостенных углеродных нанотрубок (МУНТ) и многослойных графеновых нанопластинок (МГ) соответственно. Впервые проведено исследование зависимости удельной объемной электрической проводимости нанокомпозитов на основе битума от концентрации наноструктурного углеродного наполнителя (МУНТ и МГ). Максимальные значения электрической проводимости составили 4,76×10−4 См/см и 3,5×10−4 См/см для нанокомпозитов, содержащих 6 масс. % МУНТ и 11 масс. % МГ соответственно. Определены объемные доли наполнителя на пороге перколяции для нанокомпозитов, содержащих МУНТ и МГ. Они составили 0,22 и 2,18 соответственно. Образование перколяционного контура у нанокомпозитов, содержащих МУНТ, происходит при значительно меньших концентрациях наполнителя по сравнению с битумными композициями, имеющими в своем составе МГ.
- 1 January 2023
- Published by Togliatti State University in Frontier materials & technologies
- No. 2,p. 131-139
Open AccessElectrically conductive nanocomposite bituminous binders containing carbon nanotubes and multilayer graphene
В современной литературе практически отсутствуют данные об электрических характеристиках битумных вяжущих, модифицированных углеродными нанотрубками и графеновыми нанопластинками, между тем как они необходимы для проектирования и разработки инновационных составов асфальтовых покрытий, восприимчивых к сверхвысокочастотному микроволновому излучению. Современные битумные вяжущие представляют собой многокомпонентные системы, которые могут содержать полимеры, каучуки, синтетические или природные смолы, неорганические соли и даже ароматизаторы. В результате применения модифицирующих добавок битум приобретает высокие эксплуатационные характеристики. Особый класс модификаторов составляют микро- и наноразмерные электропроводящие волокна и частицы (стальная вата, углеродные волокна, технический углерод, углеродные нанотрубки, графеновые нанопластинки), применение которых позволяет обеспечивать восприимчивость битумных вяжущих к сверхвысокочастотному микроволновому излучению и реализацию процесса залечивания трещин в асфальтовом покрытии с его последующей регенерацией. В рамках исследования разработана оригинальная методика получения битумных вяжущих, модифицированных углеродными нанотрубками и многослойным графеном. Экспериментально получены модифицированные битумные составы в диапазоне концентраций от 0,2 до 6 и от 0,2 до 11 масс. % для многостенных углеродных нанотрубок (МУНТ) и многослойных графеновых нанопластинок (МГ) соответственно. Впервые проведено исследование зависимости удельной объемной электрической проводимости нанокомпозитов на основе битума от концентрации наноструктурного углеродного наполнителя (МУНТ и МГ). Максимальные значения электрической проводимости составили 4,76×10−4 См/см и 3,5×10−4 См/см для нанокомпозитов, содержащих 6 масс. % МУНТ и 11 масс. % МГ соответственно. Определены объемные доли наполнителя на пороге перколяции для нанокомпозитов, содержащих МУНТ и МГ. Они составили 0,22 и 2,18 соответственно. Образование перколяционного контура у нанокомпозитов, содержащих МУНТ, происходит при значительно меньших концентрациях наполнителя по сравнению с битумными композициями, имеющими в своем составе МГ.
- 20 October 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 379
Reduced graphene oxide based composite aerogels for energy storage and transportation of methane
- 20 October 2022
- Published by Elsevier in Journal of Cleaner Production
- Vol. 379
Reduced graphene oxide based composite aerogels for energy storage and transportation of methane
- 30 September 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 13 (5) , 1333-1339
Sorption Properties of Graphene Aerogel with Respect to Methane
A new nanostructured carbon material has been synthesized in the form of aerogel on the basis of reduced graphene oxide using supercritical methods of hydrogel processing in the medium of isopropyl alcohol. The synthesized material is characterized by a sufficiently high BET (Brunauer, Emmett, and Teller) specific area, 657 m2/g, with high specific volume of pores according to the density functional theory (DFT), 0.766 cm3/g, which provides wide opportunities of its application for adsorption of energetically important gases, in particular, methane. A favorable factor for improvement of adsorption–desorption is high volume of mesopores with the diameters of about 4.5–6.5 nm. Methane adsorption has been studied on the synthesized graphene aerogel at temperatures of 298.15, 303.15, 313.15 K and pressures up to 10 MPa. The maximum methane adsorption at 298.15 K and 10 MPa reaches 7.31 mmol/g. Characteristic adsorption variables have been analyzed using empirical models of the Langmuir and Freundlich isotherms. Adsorption has been analyzed at the level of evaluation of thermodynamic parameters, which indicate its change from a random to ordered state and its exothermic and physical essence. The obtained results can be used in the design of storage systems of adsorbed natural gas.
- 30 September 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 13 (5) , 1333-1339
Sorption Properties of Graphene Aerogel with Respect to Methane
A new nanostructured carbon material has been synthesized in the form of aerogel on the basis of reduced graphene oxide using supercritical methods of hydrogel processing in the medium of isopropyl alcohol. The synthesized material is characterized by a sufficiently high BET (Brunauer, Emmett, and Teller) specific area, 657 m2/g, with high specific volume of pores according to the density functional theory (DFT), 0.766 cm3/g, which provides wide opportunities of its application for adsorption of energetically important gases, in particular, methane. A favorable factor for improvement of adsorption–desorption is high volume of mesopores with the diameters of about 4.5–6.5 nm. Methane adsorption has been studied on the synthesized graphene aerogel at temperatures of 298.15, 303.15, 313.15 K and pressures up to 10 MPa. The maximum methane adsorption at 298.15 K and 10 MPa reaches 7.31 mmol/g. Characteristic adsorption variables have been analyzed using empirical models of the Langmuir and Freundlich isotherms. Adsorption has been analyzed at the level of evaluation of thermodynamic parameters, which indicate its change from a random to ordered state and its exothermic and physical essence. The obtained results can be used in the design of storage systems of adsorbed natural gas.
- 30 September 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 13 (5) , 1352-1358
Microporous Carbon Material with High Volumetric Capacity of Methane Accumulation
This article discusses synthesis of compacted microporous carbon material (CMC-032) characterized by a set of unique properties: high BET specific surface area (SBET = 2384 m2/g), high volume of micropores (~0.95 cm3/g), and very high ability to retain methane of 336 m3/m3. The CMC-032 sorbent has been produced by activation of polymer raw stuff by potassium hydroxide and its compaction by hot pressing using polyvinyl alcohol as a binder. In the most demanded pressure range of methane accumulation of 3.5–10 MPa, the amount of accumulated methane in the system with CMC-032 reaches 270 m3/m3. The amount of methane stored in the system with and without CMC-032 adsorbent at 10 MPa differs by about a factor of three. The physicochemical properties of the produced CMC-032 adsorbent have been studied by methods including adsorption/desorption of N2 at 77 K, X-ray structural analysis, Fourier transform infrared spectroscopy, Raman spectroscopy, and transmission electron microscopy. It has been established on the basis of adsorption properties that CMC-032 is a promising material for accumulation of natural methane gas. It is assumed that the high adsorption capacity is due to the high volume of micropores and packing density.
- 30 September 2022
- Published by Pleiades Publishing Ltd in Inorganic Materials: Applied Research
- Vol. 13 (5) , 1352-1358
Microporous Carbon Material with High Volumetric Capacity of Methane Accumulation
This article discusses synthesis of compacted microporous carbon material (CMC-032) characterized by a set of unique properties: high BET specific surface area (SBET = 2384 m2/g), high volume of micropores (~0.95 cm3/g), and very high ability to retain methane of 336 m3/m3. The CMC-032 sorbent has been produced by activation of polymer raw stuff by potassium hydroxide and its compaction by hot pressing using polyvinyl alcohol as a binder. In the most demanded pressure range of methane accumulation of 3.5–10 MPa, the amount of accumulated methane in the system with CMC-032 reaches 270 m3/m3. The amount of methane stored in the system with and without CMC-032 adsorbent at 10 MPa differs by about a factor of three. The physicochemical properties of the produced CMC-032 adsorbent have been studied by methods including adsorption/desorption of N2 at 77 K, X-ray structural analysis, Fourier transform infrared spectroscopy, Raman spectroscopy, and transmission electron microscopy. It has been established on the basis of adsorption properties that CMC-032 is a promising material for accumulation of natural methane gas. It is assumed that the high adsorption capacity is due to the high volume of micropores and packing density.
- 1 January 2022
- Published by Science & Technology in Materials Science
- No. 7
SYNTHESIS OF NANOPOROUS CARBON MATERIAL BASED ON POLYMER RAW MATERIALS
A mixture of furfural, hydroquinone, and urotropine has been used as a new precursor for synthesis of nanoporous carbon material, using KOH activation. The optimal synthesis conditions, temperature and activation time were found to be 1 hour and 750 °C, respectively. These conditions make possible to obtain microporous carbon material with a pore volume of 1.2 cm3 / g and a BET surface area of ~3000 m2 / g.
- 1 January 2022
- Published by Science & Technology in Materials Science
- No. 7
SYNTHESIS OF NANOPOROUS CARBON MATERIAL BASED ON POLYMER RAW MATERIALS
A mixture of furfural, hydroquinone, and urotropine has been used as a new precursor for synthesis of nanoporous carbon material, using KOH activation. The optimal synthesis conditions, temperature and activation time were found to be 1 hour and 750 °C, respectively. These conditions make possible to obtain microporous carbon material with a pore volume of 1.2 cm3 / g and a BET surface area of ~3000 m2 / g.