Gregory D. Grant
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Gregory D. Grant has a total of 61 co-authors. Here are the top co-authors by number of shared publications:
- F. Joseph Heremans
Materials Science Division, Argonne National Laboratory 1 , Lemont, Illinois 60439
10 shared publications - Supratik Guha
Materials Science Division, Argonne National Laboratory 1 , Lemont, Illinois 60439
10 shared publications - David D. Awschalom
Pritzker School of Molecular Engineering, University of Chicago, Chicago, Illinois 60637, USA
9 shared publications - Ignas Masiulionis
Pritzker School of Molecular Engineering, University of Chicago 1 , Chicago, Illinois 60637
8 shared publications - Alan M. Dibos
Argonne National Laboratory
6 shared publications - Jiefei Zhang
Materials Science Division, Argonne National Laboratory 1 , Lemont, Illinois 60439
6 shared publications
Latest Publications
- 9 November 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (19)
Optical decoherence in Er3+-doped CeO2 spin qubit platforms
Erbium ions (Er3+) in cerium dioxide (CeO2) represent a promising spin–photon interface for quantum communication, but the mechanisms limiting their optical coherence remain poorly understood. Using periodic hybrid density functional theory calculations with finite-size corrections, we identify Ce3+ polarons and their complexes with oxygen vacancies and Er3+ dopants as likely sources of optical decoherence. These defects exhibit finite photoionization cross-sections at 0.8 eV, coinciding with both the laser excitation energy used experimentally and the emission energy of Er3+. The finite cross-section enables photoionization of the polarons and photoluminescence quenching of Er3+, contributing to the broadening of optical linewidths, shortening of excited-state lifetimes, and introduction of charge noise. Our concentration-dependent photocurrent measurements in Er3+-doped CeO2 films under 0.8 eV illumination validate the predicted decoherence pathway. Our combined computational and experimental results identify that removing Ce3+ polarons will improve the Er3+-doped CeO2 platform, and point to a decoherence mechanism likely relevant to other Er3+-doped multivalent-oxide quantum platforms.
- 9 November 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (19)
Optical decoherence in Er3+-doped CeO2 spin qubit platforms
Erbium ions (Er3+) in cerium dioxide (CeO2) represent a promising spin–photon interface for quantum communication, but the mechanisms limiting their optical coherence remain poorly understood. Using periodic hybrid density functional theory calculations with finite-size corrections, we identify Ce3+ polarons and their complexes with oxygen vacancies and Er3+ dopants as likely sources of optical decoherence. These defects exhibit finite photoionization cross-sections at 0.8 eV, coinciding with both the laser excitation energy used experimentally and the emission energy of Er3+. The finite cross-section enables photoionization of the polarons and photoluminescence quenching of Er3+, contributing to the broadening of optical linewidths, shortening of excited-state lifetimes, and introduction of charge noise. Our concentration-dependent photocurrent measurements in Er3+-doped CeO2 films under 0.8 eV illumination validate the predicted decoherence pathway. Our combined computational and experimental results identify that removing Ce3+ polarons will improve the Er3+-doped CeO2 platform, and point to a decoherence mechanism likely relevant to other Er3+-doped multivalent-oxide quantum platforms.
- Open Access
- 21 October 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (6)
Microstructural and optical characterization of Erbium-doped calcium tungstate films on yttria-stabilized zirconia
Er3+-doped bulk CaWO4 has been demonstrated to be a promising platform for quantum repeaters. However, the use of bulk crystals presents challenges for device integration and scalability. In this paper, we address the scalability of this platform by realizing thin-film CaWO4 growth on yttria-stabilized zirconia wafers, a step toward a CMOS-compatible heterogeneous platform. The films were deposited via radio-frequency magnetron sputtering, a scalable method, followed by postdeposition annealing and were in situ doped with Er. Optical characterization of the Er3+ ions in these films reveals lifetimes of 2.28 ± 0.16 ms, inhomogeneous linewidths of 48.29 ± 0.96 GHz, and a spectral-diffusion-limited homogeneous linewidth of 12.61 ± 2.79 MHz. These results are comparable to previously reported Er3+ in rare-earth oxide thin film hosts. The results highlight the potential of sputtered Er3+-doped CaWO4 thin films for quantum coherent applications.
- 21 October 2026
- Published by American Vacuum Society in Journal of Vacuum Science & Technology A
- Vol. 44 (6)
Open AccessMicrostructural and optical characterization of Erbium-doped calcium tungstate films on yttria-stabilized zirconia
Er3+-doped bulk CaWO4 has been demonstrated to be a promising platform for quantum repeaters. However, the use of bulk crystals presents challenges for device integration and scalability. In this paper, we address the scalability of this platform by realizing thin-film CaWO4 growth on yttria-stabilized zirconia wafers, a step toward a CMOS-compatible heterogeneous platform. The films were deposited via radio-frequency magnetron sputtering, a scalable method, followed by postdeposition annealing and were in situ doped with Er. Optical characterization of the Er3+ ions in these films reveals lifetimes of 2.28 ± 0.16 ms, inhomogeneous linewidths of 48.29 ± 0.96 GHz, and a spectral-diffusion-limited homogeneous linewidth of 12.61 ± 2.79 MHz. These results are comparable to previously reported Er3+ in rare-earth oxide thin film hosts. The results highlight the potential of sputtered Er3+-doped CaWO4 thin films for quantum coherent applications.
- Open Access
- 7 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (10)
Enhancing erbium optical emission rate via high-throughput host crystal selection
Erbium-doped solid-state crystals present an attractive platform for quantum communication, combining the telecom C-band spin–photon interface and long coherence times of erbium (Er3+) with the versatility of solid-state hosts. However, across commonly investigated materials, Er3+ is a “dim” ion, with low optical emission rates of kilohertz at most. This makes implementing quantum information transfer protocols (e.g., quantum teleportation) at usable rates a major challenge. One route to increasing Er3+ radiative rates is by careful selection of crystal hosts: the crystal field around an Er3+ ion may hybridize states of different parity, potentially increasing the radiative rate of its telecom transition. Here, using high-throughput computational methods, the radiative rates of Er3+ embedded in 9215 materials are estimated. The computation shows that careful host selection could increase Er3+ radiative rates by an order of magnitude compared to commonly studied hosts. Calculated results are compared with experimental radiative rates in a subset of materials, finding notable clustering but weak correlation. Nevertheless, the “brightest” candidates combined with suitable nanophotonics engineering could push Er3+-based quantum memories into the megahertz bandwidth regime.
- 7 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (10)
Open AccessEnhancing erbium optical emission rate via high-throughput host crystal selection
Erbium-doped solid-state crystals present an attractive platform for quantum communication, combining the telecom C-band spin–photon interface and long coherence times of erbium (Er3+) with the versatility of solid-state hosts. However, across commonly investigated materials, Er3+ is a “dim” ion, with low optical emission rates of kilohertz at most. This makes implementing quantum information transfer protocols (e.g., quantum teleportation) at usable rates a major challenge. One route to increasing Er3+ radiative rates is by careful selection of crystal hosts: the crystal field around an Er3+ ion may hybridize states of different parity, potentially increasing the radiative rate of its telecom transition. Here, using high-throughput computational methods, the radiative rates of Er3+ embedded in 9215 materials are estimated. The computation shows that careful host selection could increase Er3+ radiative rates by an order of magnitude compared to commonly studied hosts. Calculated results are compared with experimental radiative rates in a subset of materials, finding notable clustering but weak correlation. Nevertheless, the “brightest” candidates combined with suitable nanophotonics engineering could push Er3+-based quantum memories into the megahertz bandwidth regime.
- 26 December 2025
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 135 (26) , 266901
Spin Decoherence Dynamics of Er 3 + in CeO 2 Films
Developing telecom-compatible spin-photon interfaces is essential towards scalable quantum networks. Erbium ions (Er^{3+}) exhibit a unique combination of a telecom (1.5 μm) optical transition and an effective spin-1/2 ground state, but identifying a host that enables heterogeneous device integration while preserving long optical and spin coherence remains an open challenge. We explore the potential of Er^{3+}:CeO_{2} films on silicon and study the Er^{3+} spin coherence, offering low nuclear spin density and the potential for on-chip integration. We demonstrate a 38.8 μs spin coherence, which can be extended to 176.4 μs with dynamical decoupling. Pairing experiments with cluster correlation expansion calculations, we identify spectral diffusion induced by bath Er^{3+} spin flip-flops as the dominant decoherence mechanism and provide pathways to millisecond-scale coherence.
- 26 December 2025
- Published by American Physical Society (APS) in Physical Review Letters
- Vol. 135 (26) , 266901
Spin Decoherence Dynamics of Er 3 + in CeO 2 Films
Developing telecom-compatible spin-photon interfaces is essential towards scalable quantum networks. Erbium ions (Er^{3+}) exhibit a unique combination of a telecom (1.5 μm) optical transition and an effective spin-1/2 ground state, but identifying a host that enables heterogeneous device integration while preserving long optical and spin coherence remains an open challenge. We explore the potential of Er^{3+}:CeO_{2} films on silicon and study the Er^{3+} spin coherence, offering low nuclear spin density and the potential for on-chip integration. We demonstrate a 38.8 μs spin coherence, which can be extended to 176.4 μs with dynamical decoupling. Pairing experiments with cluster correlation expansion calculations, we identify spectral diffusion induced by bath Er^{3+} spin flip-flops as the dominant decoherence mechanism and provide pathways to millisecond-scale coherence.
- Open Access
- 1 October 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (10)
Microstructural and preliminary optical and microwave characterization of erbium-doped CaMoO4 thin films
This work explores erbium-doped calcium molybdate (Er:CaMoO4) thin films grown on silicon and yttria stabilized zirconia (YSZ) substrates, as a potential solid state system for C-band (utilizing the ∼1.5 μm Er3+ 4f–4f transition) quantum emitters for quantum network applications. Through molecular beam epitaxial growth experiments and electron microscopy, X-ray diffraction, and reflection electron diffraction studies, we identify an incorporation limited deposition regime that enables a 1:1 Ca:Mo ratio in the growing film leading to single phase CaMoO4 formation that can be in situ doped with Er (typically 2–100 ppm). We further show that growth on silicon substrates is single phase but polycrystalline in morphology, while growth on YSZ substrates leads to high-quality epitaxial single crystalline CaMoO4 films. We perform preliminary optical and microwave characterization on the suspected Y1–Z1 transition of 2 ppm, 200 nm epitaxial Er:CaMoO4 annealed thin films and extract an optical inhomogeneous linewidth of 9.1(1) GHz, an optical excited state lifetime of 6.7(2) ms, a spectral diffusion-limited homogeneous linewidth of 6.7(4) MHz, and an EPR linewidth of 1.10(2) GHz.
- 1 October 2025
- Published by AIP Publishing in APL Materials
- Vol. 13 (10)
Open AccessMicrostructural and preliminary optical and microwave characterization of erbium-doped CaMoO4 thin films
This work explores erbium-doped calcium molybdate (Er:CaMoO4) thin films grown on silicon and yttria stabilized zirconia (YSZ) substrates, as a potential solid state system for C-band (utilizing the ∼1.5 μm Er3+ 4f–4f transition) quantum emitters for quantum network applications. Through molecular beam epitaxial growth experiments and electron microscopy, X-ray diffraction, and reflection electron diffraction studies, we identify an incorporation limited deposition regime that enables a 1:1 Ca:Mo ratio in the growing film leading to single phase CaMoO4 formation that can be in situ doped with Er (typically 2–100 ppm). We further show that growth on silicon substrates is single phase but polycrystalline in morphology, while growth on YSZ substrates leads to high-quality epitaxial single crystalline CaMoO4 films. We perform preliminary optical and microwave characterization on the suspected Y1–Z1 transition of 2 ppm, 200 nm epitaxial Er:CaMoO4 annealed thin films and extract an optical inhomogeneous linewidth of 9.1(1) GHz, an optical excited state lifetime of 6.7(2) ms, a spectral diffusion-limited homogeneous linewidth of 6.7(4) MHz, and an EPR linewidth of 1.10(2) GHz.
- Open Access
- 1 December 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (12)
The role of the dopant in the electronic structure of erbium-doped TiO2 for quantum emitters
Erbium-doped TiO2 materials are promising candidates for advancing quantum technologies, necessitating a thorough understanding of their electronic and crystal structures to tailor their properties and enhance coherence times. This study explored epitaxial erbium-doped rutile TiO2 films deposited on r-sapphire substrates using molecular beam epitaxy. Photoluminescence excitation spectroscopy demonstrated decreasing photoluminescence lifetimes with erbium doping, indicating limited optical coherence times. Lattice distortions associated with Er3+ were probed by x-ray absorption spectroscopy, indicating that erbium primarily occupies Ti4+ sites and influences oxygen vacancies. Significant lattice distortions in the higher-order shells and apparent full coordination around erbium suggest that additional defects are likely prevalent in these regions. These findings indicate that defects contribute to limited coherence times by introducing alternative decay pathways, leading to shorter photoluminescence lifetimes.
- 1 December 2024
- Published by AIP Publishing in APL Materials
- Vol. 12 (12)
Open AccessThe role of the dopant in the electronic structure of erbium-doped TiO2 for quantum emitters
Erbium-doped TiO2 materials are promising candidates for advancing quantum technologies, necessitating a thorough understanding of their electronic and crystal structures to tailor their properties and enhance coherence times. This study explored epitaxial erbium-doped rutile TiO2 films deposited on r-sapphire substrates using molecular beam epitaxy. Photoluminescence excitation spectroscopy demonstrated decreasing photoluminescence lifetimes with erbium doping, indicating limited optical coherence times. Lattice distortions associated with Er3+ were probed by x-ray absorption spectroscopy, indicating that erbium primarily occupies Ti4+ sites and influences oxygen vacancies. Significant lattice distortions in the higher-order shells and apparent full coordination around erbium suggest that additional defects are likely prevalent in these regions. These findings indicate that defects contribute to limited coherence times by introducing alternative decay pathways, leading to shorter photoluminescence lifetimes.
- Open Access
- 26 September 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (12)
Optical and microstructural studies of erbium-doped TiO2 thin films on silicon, SrTiO3, and sapphire
Rare-earth ion doped oxide thin films integrated on silicon substrates provide a route toward scalable, chip-scale platforms for quantum coherent devices. Erbium-doped TiO2 is an attractive candidate: the Er3+ optical transition is compatible with C-band optical fiber communications, while TiO2 is an insulating dielectric compatible with silicon process technology. Through structural and optical studies of Er-doped TiO2 thin films grown via molecular beam deposition on silicon, SrTiO3, and sapphire substrates, we have explored the impact of polycrystallinity and microstructure on the optical properties of the Er emission. Comparing polycrystalline TiO2(rutile)/Si with single-crystalline TiO2(rutile)/r-sapphire and polycrystalline TiO2(anatase)/Si with single-crystalline TiO2(anatase)/SrTiO3, we observe that the inhomogeneous linewidth (Γinh) of the most prominent peak in the Er spectrum (the Y1–Z1 transition, 1520 and 1533 nm in rutile and anatase TiO2) is significantly narrower in the polycrystalline case. This implies a relative insensitivity to extended structural defects and grain boundaries in such films (as opposed to, e.g., point defects). We show that the growth of an undoped, underlying TiO2 buffer on Si can reduce Γinh by a factor of 4–5. Expectedly, Γinh also reduces with decreasing Er concentrations: we observe a ∼2 order of magnitude reduction from ∼1000 ppm Er to ∼10 ppm Er. Γinh then gets limited to a residual value of ∼5 GHz that is insensitive to further reduction in the Er concentration. Based upon the above results, we argue that the optical properties in these thin films are limited by the presence of high “grown-in” point defect concentrations.
- 26 September 2024
- Published by AIP Publishing in Journal of Applied Physics
- Vol. 136 (12)
Open AccessOptical and microstructural studies of erbium-doped TiO2 thin films on silicon, SrTiO3, and sapphire
Rare-earth ion doped oxide thin films integrated on silicon substrates provide a route toward scalable, chip-scale platforms for quantum coherent devices. Erbium-doped TiO2 is an attractive candidate: the Er3+ optical transition is compatible with C-band optical fiber communications, while TiO2 is an insulating dielectric compatible with silicon process technology. Through structural and optical studies of Er-doped TiO2 thin films grown via molecular beam deposition on silicon, SrTiO3, and sapphire substrates, we have explored the impact of polycrystallinity and microstructure on the optical properties of the Er emission. Comparing polycrystalline TiO2(rutile)/Si with single-crystalline TiO2(rutile)/r-sapphire and polycrystalline TiO2(anatase)/Si with single-crystalline TiO2(anatase)/SrTiO3, we observe that the inhomogeneous linewidth (Γinh) of the most prominent peak in the Er spectrum (the Y1–Z1 transition, 1520 and 1533 nm in rutile and anatase TiO2) is significantly narrower in the polycrystalline case. This implies a relative insensitivity to extended structural defects and grain boundaries in such films (as opposed to, e.g., point defects). We show that the growth of an undoped, underlying TiO2 buffer on Si can reduce Γinh by a factor of 4–5. Expectedly, Γinh also reduces with decreasing Er concentrations: we observe a ∼2 order of magnitude reduction from ∼1000 ppm Er to ∼10 ppm Er. Γinh then gets limited to a residual value of ∼5 GHz that is insensitive to further reduction in the Er concentration. Based upon the above results, we argue that the optical properties in these thin films are limited by the presence of high “grown-in” point defect concentrations.
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Isolation of individual Er quantum emitters in anatase TiO2 on Si photonics
Defects and dopant atoms in solid state materials are a promising platform for realizing single photon sources and quantum memories, which are the basic building blocks of quantum repeaters needed for long distance quantum networks. In particular, trivalent erbium (Er3+) is of interest because it couples C-band telecom optical transitions with a spin-based memory platform. In order to produce quantum repeaters at the scale required for quantum networks it is imperative to integrate these necessary building blocks with mature and scalable semiconductor processes. In this work, we demonstrate the optical isolation of single Er3+ ions in CMOS-compatible titanium dioxide (TiO2) thin films monolithically integrated on a silicon-on-insulator photonics platform. Our results demonstrate an initial step toward the realization of a monolithically integrated and scalable quantum photonics package based on Er3+ doped thin films.
- 19 August 2024
- Published by AIP Publishing in Applied Physics Letters
- Vol. 125 (8)
Isolation of individual Er quantum emitters in anatase TiO2 on Si photonics
Defects and dopant atoms in solid state materials are a promising platform for realizing single photon sources and quantum memories, which are the basic building blocks of quantum repeaters needed for long distance quantum networks. In particular, trivalent erbium (Er3+) is of interest because it couples C-band telecom optical transitions with a spin-based memory platform. In order to produce quantum repeaters at the scale required for quantum networks it is imperative to integrate these necessary building blocks with mature and scalable semiconductor processes. In this work, we demonstrate the optical isolation of single Er3+ ions in CMOS-compatible titanium dioxide (TiO2) thin films monolithically integrated on a silicon-on-insulator photonics platform. Our results demonstrate an initial step toward the realization of a monolithically integrated and scalable quantum photonics package based on Er3+ doped thin films.
- 18 June 2024
- Published by Optica Publishing Group in Optica Quantum
- Vol. 2 (3) , 196
Anomalous Purcell decay of strongly driven inhomogeneous emitters coupled to a cavity
We perform resonant fluorescence lifetime measurements on a nanocavity-coupled erbium ensemble as a function of cavity-laser detuning and pump power. Our measurements reveal an anomalous three-fold suppression of the ensemble Purcell factor at zero cavity detuning and high pump fluence. We capture qualitative aspects of this decay rate suppression using a Tavis–Cummings model of non-interacting spins coupled to a common cavity.
- 18 June 2024
- Published by Optica Publishing Group in Optica Quantum
- Vol. 2 (3) , 196
Anomalous Purcell decay of strongly driven inhomogeneous emitters coupled to a cavity
We perform resonant fluorescence lifetime measurements on a nanocavity-coupled erbium ensemble as a function of cavity-laser detuning and pump power. Our measurements reveal an anomalous three-fold suppression of the ensemble Purcell factor at zero cavity detuning and high pump fluence. We capture qualitative aspects of this decay rate suppression using a Tavis–Cummings model of non-interacting spins coupled to a common cavity.
- Open Access
- 27 March 2024
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 18 (14) , 9929-9941
Nanocavity-Mediated Purcell Enhancement of Er in TiO2 Thin Films Grown via Atomic Layer Deposition
The use of trivalent erbium (Er3+), typically embedded as an atomic defect in the solid-state, has widespread adoption as a dopant in telecommunication devices and shows promise as a spin-based quantum memory for quantum communication. In particular, its natural telecom C-band optical transition and spin-photon interface make it an ideal candidate for integration into existing optical fiber networks without the need for quantum frequency conversion. However, successful scaling requires a host material with few intrinsic nuclear spins, compatibility with semiconductor foundry processes, and straightforward integration with silicon photonics. Here, we present Er-doped titanium dioxide (TiO2) thin film growth on silicon substrates using a foundry-scalable atomic layer deposition process with a wide range of doping controls over the Er concentration. Even though the as-grown films are amorphous after oxygen annealing, they exhibit relatively large crystalline grains, and the embedded Er ions exhibit the characteristic optical emission spectrum from anatase TiO2. Critically, this growth and annealing process maintains the low surface roughness required for nanophotonic integration. Finally, we interface Er ensembles with high quality factor Si nanophotonic cavities via evanescent coupling and demonstrate a large Purcell enhancement (≈300) of their optical lifetime. Our findings demonstrate a low-temperature, nondestructive, and substrate-independent process for integrating Er-doped materials with silicon photonics. At high doping densities this platform can enable integrated photonic components such as on-chip amplifiers and lasers, while dilute concentrations can realize single ion quantum memories.
- 27 March 2024
- Published by American Chemical Society (ACS) in ACS Nano
- Vol. 18 (14) , 9929-9941
Open AccessNanocavity-Mediated Purcell Enhancement of Er in TiO2 Thin Films Grown via Atomic Layer Deposition
The use of trivalent erbium (Er3+), typically embedded as an atomic defect in the solid-state, has widespread adoption as a dopant in telecommunication devices and shows promise as a spin-based quantum memory for quantum communication. In particular, its natural telecom C-band optical transition and spin-photon interface make it an ideal candidate for integration into existing optical fiber networks without the need for quantum frequency conversion. However, successful scaling requires a host material with few intrinsic nuclear spins, compatibility with semiconductor foundry processes, and straightforward integration with silicon photonics. Here, we present Er-doped titanium dioxide (TiO2) thin film growth on silicon substrates using a foundry-scalable atomic layer deposition process with a wide range of doping controls over the Er concentration. Even though the as-grown films are amorphous after oxygen annealing, they exhibit relatively large crystalline grains, and the embedded Er ions exhibit the characteristic optical emission spectrum from anatase TiO2. Critically, this growth and annealing process maintains the low surface roughness required for nanophotonic integration. Finally, we interface Er ensembles with high quality factor Si nanophotonic cavities via evanescent coupling and demonstrate a large Purcell enhancement (≈300) of their optical lifetime. Our findings demonstrate a low-temperature, nondestructive, and substrate-independent process for integrating Er-doped materials with silicon photonics. At high doping densities this platform can enable integrated photonic components such as on-chip amplifiers and lasers, while dilute concentrations can realize single ion quantum memories.