Marco Antonio Braga
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Marco Antonio Braga has a total of 37 co-authors. Here are the top co-authors by number of shared publications:
- Maria Filipa Perez da Gama
UFRJ 2 , Rio de Janeiro, .;.
4 shared publications - Gilvan Sá
Universidade Federal de Ouro Preto - UFOP
3 shared publications - Iuri Viana Brandi
VALE S.A.
3 shared publications - Leonardo Santana de Oliveira Dias
Universidade Federal do Rio de Janeiro - UFRJ, Brasil
3 shared publications - Marcelo Roberto Barbosa
Vale S.A., Nova Lima, Minas Gerais, Brazil
3 shared publications - Alan De Souza Cunha
Universidade Federal do Rio de Janeiro - UFRJ, Brasil
2 shared publications
Latest Publications
- Open Access
- 1 January 2026
- Published by FapUNIFESP (SciELO) in REM - International Engineering Journal
- Vol. 79 (2)
Empirical correction model for cased-hole gamma-gamma density logs in phosphate mining
In recent years, military conflicts between major phosphorus suppliers have disrupted the global fertilizer distribution chain. This scenario highlights the critical need for precise density measurements in phosphate mining to improve reserve estimation and reconciliation. In Brazil, formation density is traditionally estimated from drill cores, using hydrostatic balance methods, which can be time-consuming and less reliable for poorly consolidated rocks. Gamma-gamma geophysical logging emerges as a more effective alternative, offering high-resolution density data with rapid acquisition. The use of these nuclear tools requires some special care, such as data acquisition from the inside of boreholes with steel casing, essential for operational safety. However, this procedure introduces measurement changes in the density log readings. This study aimed to comprehend the main factors involved in these gamma-gamma readings through direct comparisons between logging records made in holes with and without casing. In this way, it was possible to suggest a workflow to correct density readings when influenced by the presence of steel casing. Data from four boreholes drilled in the Tapira Mining Complex, Minas Gerais (Brazil) were used. The correction creates synthetic density records that present good correspondence with measurements from uncased boreholes while being supported by borehole diameter control from caliper records. Finally, the results show that gamma-gamma density logging, applied to cased holes, can be a reliable and efficient method for density measurement in phosphate deposits, especially in friable ore zones.
- 1 January 2026
- Published by FapUNIFESP (SciELO) in REM - International Engineering Journal
- Vol. 79 (2)
Open AccessEmpirical correction model for cased-hole gamma-gamma density logs in phosphate mining
In recent years, military conflicts between major phosphorus suppliers have disrupted the global fertilizer distribution chain. This scenario highlights the critical need for precise density measurements in phosphate mining to improve reserve estimation and reconciliation. In Brazil, formation density is traditionally estimated from drill cores, using hydrostatic balance methods, which can be time-consuming and less reliable for poorly consolidated rocks. Gamma-gamma geophysical logging emerges as a more effective alternative, offering high-resolution density data with rapid acquisition. The use of these nuclear tools requires some special care, such as data acquisition from the inside of boreholes with steel casing, essential for operational safety. However, this procedure introduces measurement changes in the density log readings. This study aimed to comprehend the main factors involved in these gamma-gamma readings through direct comparisons between logging records made in holes with and without casing. In this way, it was possible to suggest a workflow to correct density readings when influenced by the presence of steel casing. Data from four boreholes drilled in the Tapira Mining Complex, Minas Gerais (Brazil) were used. The correction creates synthetic density records that present good correspondence with measurements from uncased boreholes while being supported by borehole diameter control from caliper records. Finally, the results show that gamma-gamma density logging, applied to cased holes, can be a reliable and efficient method for density measurement in phosphate deposits, especially in friable ore zones.
- Open Access
- 3 June 2025
- Published by Sociedade Brasileira de Geofisica in Brazilian Journal of Geophysics
- Vol. 43 (2)
Improvements in the Characterization of Phosphate Deposits Using Well Logging in the Tapira Alkaline-Carbonatite Complex, Minas Gerais, Brazil
Improvements in the Characterization of Phosphate Deposits Using Well Logging in the Tapira Alkaline-Carbonatite Complex, Minas Gerais, Brazil
- 3 June 2025
- Published by Sociedade Brasileira de Geofisica in Brazilian Journal of Geophysics
- Vol. 43 (2)
Open AccessImprovements in the Characterization of Phosphate Deposits Using Well Logging in the Tapira Alkaline-Carbonatite Complex, Minas Gerais, Brazil
Improvements in the Characterization of Phosphate Deposits Using Well Logging in the Tapira Alkaline-Carbonatite Complex, Minas Gerais, Brazil
- Open Access
- 6 January 2025
- Published by Universidade Federal do Rio Grande do Norte - UFRN in Revista de Geociências do Nordeste
- Vol. 11 (1) , 696-707
Assessment of Geoelectrical and Seismic Methods for Tailing Dams – Catalão GO
Mining tailings dams are engineered structures designed for the disposal of waste materials generated during mineral processing. These structures require continuous geotechnical monitoring, including visual inspections and manual or automated instrumentation, to ensure their safety and stability. This paper presents the application and results of geophysical methods used to monitor and investigate a tailings dam. In Brazil, recent dam failures have prompted significant improvements in legislation, technical standards, and geotechnical investigation protocols. Electrical resistivity was employed to map low-resistivity zones, which are associated with higher degrees of saturation within the dam structure. Ambient noise seismic interferometry enabled real-time monitoring of variations in S-wave velocity (Vs), with reductions reaching 11% at the dam crest. This reduction was linked to higher saturation levels near the right abutment, likely intensified by seasonal rainfall. Additionally, the multichannel analysis of surface waves confirmed the decrease in Vs in areas correlated with those of low resistivity, suggesting increased saturation. Ambient Noise Seismic interferometry also detected a partial recovery in Vs over time. The integration of these geophysical techniques allowed for the identification of structural anomalies and supported the implementation of corrective engineering measures, contributing to improved dam safety and risk management.
- 6 January 2025
- Published by Universidade Federal do Rio Grande do Norte - UFRN in Revista de Geociências do Nordeste
- Vol. 11 (1) , 696-707
Open AccessAssessment of Geoelectrical and Seismic Methods for Tailing Dams – Catalão GO
Mining tailings dams are engineered structures designed for the disposal of waste materials generated during mineral processing. These structures require continuous geotechnical monitoring, including visual inspections and manual or automated instrumentation, to ensure their safety and stability. This paper presents the application and results of geophysical methods used to monitor and investigate a tailings dam. In Brazil, recent dam failures have prompted significant improvements in legislation, technical standards, and geotechnical investigation protocols. Electrical resistivity was employed to map low-resistivity zones, which are associated with higher degrees of saturation within the dam structure. Ambient noise seismic interferometry enabled real-time monitoring of variations in S-wave velocity (Vs), with reductions reaching 11% at the dam crest. This reduction was linked to higher saturation levels near the right abutment, likely intensified by seasonal rainfall. Additionally, the multichannel analysis of surface waves confirmed the decrease in Vs in areas correlated with those of low resistivity, suggesting increased saturation. Ambient Noise Seismic interferometry also detected a partial recovery in Vs over time. The integration of these geophysical techniques allowed for the identification of structural anomalies and supported the implementation of corrective engineering measures, contributing to improved dam safety and risk management.
- Open Access
- 6 January 2025
- Published by Universidade Federal do Rio Grande do Norte - UFRN in Revista de Geociências do Nordeste
- Vol. 11 (1) , 680-695
Monitoramento de Barragem de Rejeito Através de Métodos Geofísicos: Interferometria Sísmica do Ruído Ambiente e Eletrorresistividade – Barragem B1B4, Araxá (MG)
As barragens de rejeitos de mineração e resíduos industriais requerem monitoramento constante devido ao impacto ambiental e ao risco de rompimento. No Brasil, existem 941 barragens cadastradas, sendo 340 localizadas em Minas Gerais. Para o acompanhamento da integridade dessas estruturas, são realizados monitoramentos por meio de inspeções visuais e instrumentação convencional, como piezômetros, o que demanda tempo e planejamento para o processamento dos dados. Métodos geofísicos surgem como alternativas complementares, proporcionando maior cobertura e rapidez na aquisição de dados. Assim, este trabalho tem como objetivo avaliar os parâmetros físicos da Barragem B1B4, localizada em Araxá, por meio da interferometria sísmica, que monitora a variação da velocidade da onda S (Vs), permitindo avaliar mudanças no módulo de rigidez da estrutura, e da eletrorresistividade, que identifica zonas de umidade, categorizando-as em zonas de baixa (400 ohm.m). Os dados de interferometria mostraram maior variação de Vs durante períodos de alta pluviosidade, sugerindo alterações nas propriedades físicas do maciço. Os dados de eletrorresistividade indicaram a presença de áreas condutivas e resistivas, fornecendo informações para identificar zonas de maior umidade. A integração desses métodos demonstrou-se eficaz para monitorar mudanças nas propriedades físicas do maciço, complementando técnicas tradicionais
- 6 January 2025
- Published by Universidade Federal do Rio Grande do Norte - UFRN in Revista de Geociências do Nordeste
- Vol. 11 (1) , 680-695
Open AccessMonitoramento de Barragem de Rejeito Através de Métodos Geofísicos: Interferometria Sísmica do Ruído Ambiente e Eletrorresistividade – Barragem B1B4, Araxá (MG)
As barragens de rejeitos de mineração e resíduos industriais requerem monitoramento constante devido ao impacto ambiental e ao risco de rompimento. No Brasil, existem 941 barragens cadastradas, sendo 340 localizadas em Minas Gerais. Para o acompanhamento da integridade dessas estruturas, são realizados monitoramentos por meio de inspeções visuais e instrumentação convencional, como piezômetros, o que demanda tempo e planejamento para o processamento dos dados. Métodos geofísicos surgem como alternativas complementares, proporcionando maior cobertura e rapidez na aquisição de dados. Assim, este trabalho tem como objetivo avaliar os parâmetros físicos da Barragem B1B4, localizada em Araxá, por meio da interferometria sísmica, que monitora a variação da velocidade da onda S (Vs), permitindo avaliar mudanças no módulo de rigidez da estrutura, e da eletrorresistividade, que identifica zonas de umidade, categorizando-as em zonas de baixa (400 ohm.m). Os dados de interferometria mostraram maior variação de Vs durante períodos de alta pluviosidade, sugerindo alterações nas propriedades físicas do maciço. Os dados de eletrorresistividade indicaram a presença de áreas condutivas e resistivas, fornecendo informações para identificar zonas de maior umidade. A integração desses métodos demonstrou-se eficaz para monitorar mudanças nas propriedades físicas do maciço, complementando técnicas tradicionais
- Open Access
- 1 December 2023
- Published by FapUNIFESP (SciELO) in REM - International Engineering Journal
- Vol. 76 (4) , 363-370
Geophysical key indicators for tailings dam physical integrity monitoring - Brazil
The geotechnical monitoring of tailings dams combined with a suitable application of geophysical electrical methods can improve their structure evaluation, allowing several correlations between direct analyses and the resistivity anomaly pattern. Considering this synergy, twenty-three electrical resistivity sections (ERT) were acquired along the beach, abutments, and central part of a dam, totalizing 10,776 m of dataset. After the interpretation of each ERT section, comparing the anomaly ranges with the water level meters measurements, three resistivity zones were defined: Zones of low resistivity ( 357 ohm-m), interpreted as dry zones, and regions with intermediate resistivity values, located between these limits. The groundwater surface generated from the interpretation of the electrical resistivity dataset and the groundwater surface acquired from the water level gauges were almost coincident. On the right abutment, the conductive anomalies showed remarkable continuity, suggesting a high moisture content in this region with strong gradients (200 mV) directed towards the zone of low resistivity values identified in the sections. The analysis showed a robust correlation of the ERT data with localized physical geotechnical measurements, valuable for monitoring dam integrity, overseeing the structure's response to climate and operational changes, and ultimately mitigating the risks of failure. The results of this study support the adoption of a seasonal 4D electrical resistivity survey as an effective tool to monitor and manage surface and high humidity zones, key indicators of dam integrity throughout the entire structure.
- 1 December 2023
- Published by FapUNIFESP (SciELO) in REM - International Engineering Journal
- Vol. 76 (4) , 363-370
Open AccessGeophysical key indicators for tailings dam physical integrity monitoring - Brazil
The geotechnical monitoring of tailings dams combined with a suitable application of geophysical electrical methods can improve their structure evaluation, allowing several correlations between direct analyses and the resistivity anomaly pattern. Considering this synergy, twenty-three electrical resistivity sections (ERT) were acquired along the beach, abutments, and central part of a dam, totalizing 10,776 m of dataset. After the interpretation of each ERT section, comparing the anomaly ranges with the water level meters measurements, three resistivity zones were defined: Zones of low resistivity ( 357 ohm-m), interpreted as dry zones, and regions with intermediate resistivity values, located between these limits. The groundwater surface generated from the interpretation of the electrical resistivity dataset and the groundwater surface acquired from the water level gauges were almost coincident. On the right abutment, the conductive anomalies showed remarkable continuity, suggesting a high moisture content in this region with strong gradients (200 mV) directed towards the zone of low resistivity values identified in the sections. The analysis showed a robust correlation of the ERT data with localized physical geotechnical measurements, valuable for monitoring dam integrity, overseeing the structure's response to climate and operational changes, and ultimately mitigating the risks of failure. The results of this study support the adoption of a seasonal 4D electrical resistivity survey as an effective tool to monitor and manage surface and high humidity zones, key indicators of dam integrity throughout the entire structure.
- Open Access
- 14 October 2022
- Published by Universidade Federal do Rio de Janeiro in Anuário do Instituto de Geociências
- Vol. 45
Mining Induced Ground Motions in a Tailings Dam
Mining induced seismicity can expose tailings dams to ground motions with potential to trigger a failure, if the structure reaches a certain level of vibrations that could exceed the seismic coefficient design criteria from pseudostatic analysis. Despite the cited risk, mainly for dams that are closer to open pits, few dams in Brazil are monitored by microseismic systems, and there are no references in the literature about continuous seismic monitoring both in open pit (source) and tailings dam, which represents the motivation of this paper. A microseismic system was commissioned in Cajati Mine, São Paulo, to record seismic events continuously in an array of 16 geophones (14 Hz and 4.5 Hz), installed in boreholes near the open pit (12 sensors) and in the dam (4 sensors), has measured values of PGA (Peak Ground Acceleration) and PGV (Peak Ground Velocity) related to 2,972 induced events from rock removal in the open pit. During the period monitored, the total of 109 events have triggered sensors in both structures, producing 920 seismograms, with the highest values of PGA and PGV of 0.0135 m/s2 (0.1358% of g) and 0.0892 mm/s. The highest PGA value is 36 times lower than the vertical coefficient of 3% of g defined by Brazilian technical standard to dam design criteria, normally used in common pseudostatic analysis from geotechnical engineers. A routine microseismic monitoring brings a new set of valuable actionable data and information to support the management of geotechnical tailings dams’ risks, under the conditions of vibrations induced by mining production.
- 14 October 2022
- Published by Universidade Federal do Rio de Janeiro in Anuário do Instituto de Geociências
- Vol. 45
Open AccessMining Induced Ground Motions in a Tailings Dam
Mining induced seismicity can expose tailings dams to ground motions with potential to trigger a failure, if the structure reaches a certain level of vibrations that could exceed the seismic coefficient design criteria from pseudostatic analysis. Despite the cited risk, mainly for dams that are closer to open pits, few dams in Brazil are monitored by microseismic systems, and there are no references in the literature about continuous seismic monitoring both in open pit (source) and tailings dam, which represents the motivation of this paper. A microseismic system was commissioned in Cajati Mine, São Paulo, to record seismic events continuously in an array of 16 geophones (14 Hz and 4.5 Hz), installed in boreholes near the open pit (12 sensors) and in the dam (4 sensors), has measured values of PGA (Peak Ground Acceleration) and PGV (Peak Ground Velocity) related to 2,972 induced events from rock removal in the open pit. During the period monitored, the total of 109 events have triggered sensors in both structures, producing 920 seismograms, with the highest values of PGA and PGV of 0.0135 m/s2 (0.1358% of g) and 0.0892 mm/s. The highest PGA value is 36 times lower than the vertical coefficient of 3% of g defined by Brazilian technical standard to dam design criteria, normally used in common pseudostatic analysis from geotechnical engineers. A routine microseismic monitoring brings a new set of valuable actionable data and information to support the management of geotechnical tailings dams’ risks, under the conditions of vibrations induced by mining production.
- 5 December 2021
- Published by Sociedade Brasileira de Geofisica in Brazilian Journal of Geophysics
- Vol. 39 (4) , 489-504
Mining Blast-Induced Ground Motions in Tailings Dam
Ground motions caused by routine blasting activities represent a concern for mining companies, that face the challenge of producing without causing critical damage to tailings dams, mine pit slopes and waste piles. Few dams in Brazil are monitored by microseismic systems, and there are no references in the literature about monitoring in open pit mine and dam. In order to analyze the ground motion data induced by blats and their relationship with dam stability, it was installed a seismic system, that records events continuously in an array of 16 geophones (14 Hz and 4.5 Hz), 12 installed in an open pit and 4 in a tailings dam with value measurement of Peak Ground Acceleration, Peak Ground Velocity, dominant frequency, and seismic source parameters related to blast events. In the monitored period, sensors from the open pit and dam were analyzed and all accelerations recorded showed that ∼95% of the values are lower than 0.06 m/s2, with 90% of the records with higher dominant frequency (>10 Hz), that presents lower damage potential due to the lower capacity to produce high values of displacements. The system showed the potential to add new data and information to the current dam geotechnical instrumentation.Keywords: blast-induced seismicity, microseismic monitoring, tailings dam, risk management, geotechnical monitoring plan.Ground Motions Induzidos por Desmontes em Barragem de RejeitosRESUMO. Os ground motions gerados pelas atividades rotineiras de detonação representam uma preocupação para as mineradoras, que enfrentam o desafio de produzir sem causar danos críticos às barragens de rejeitos, taludes de cava e pilhas de estéril. Poucas barragens no Brasil são monitoradas por sistemas microssísmicos e não há referências na literatura sobre monitoramento em cava e barragem. Para analisar os dados dos ground motions causados pelas detonações e a sua relação com a estabilidade de uma barragem, foi instalado um sistema de monitoramento sísmico, que registra eventos continuamente num arranjo de 16 geofones (14 Hz e 4,5 Hz), instalados 12 na cava e 4 na barragem, com medição de valores de Peak Ground Acceleration, Peak Ground Velocity, frequência dominante e parâmetros da fonte sísmica dos desmontes. No período monitorado, quando foram analisados os sensores da mina e da barragem, todas as acelerações mostraram que ∼95% dos valores são menores que 0,06 m/s2, com 90% dos registros com maior frequência dominante (> 10 Hz), que apresenta menor potencial de dano devido à menor capacidade de produzir altos valores de deslocamentos. O sistema mostrou potencial para agregar novos dados e informações à atual instrumentação geotécnica da barragem.Palavras-chave: sismicidade induzida por desmontes, monitoramento microssísmico, barragem de rejeitos, gerenciamento de risco, plano de monitoramento geotécnico.
- 5 December 2021
- Published by Sociedade Brasileira de Geofisica in Brazilian Journal of Geophysics
- Vol. 39 (4) , 489-504
Mining Blast-Induced Ground Motions in Tailings Dam
Ground motions caused by routine blasting activities represent a concern for mining companies, that face the challenge of producing without causing critical damage to tailings dams, mine pit slopes and waste piles. Few dams in Brazil are monitored by microseismic systems, and there are no references in the literature about monitoring in open pit mine and dam. In order to analyze the ground motion data induced by blats and their relationship with dam stability, it was installed a seismic system, that records events continuously in an array of 16 geophones (14 Hz and 4.5 Hz), 12 installed in an open pit and 4 in a tailings dam with value measurement of Peak Ground Acceleration, Peak Ground Velocity, dominant frequency, and seismic source parameters related to blast events. In the monitored period, sensors from the open pit and dam were analyzed and all accelerations recorded showed that ∼95% of the values are lower than 0.06 m/s2, with 90% of the records with higher dominant frequency (>10 Hz), that presents lower damage potential due to the lower capacity to produce high values of displacements. The system showed the potential to add new data and information to the current dam geotechnical instrumentation.Keywords: blast-induced seismicity, microseismic monitoring, tailings dam, risk management, geotechnical monitoring plan.Ground Motions Induzidos por Desmontes em Barragem de RejeitosRESUMO. Os ground motions gerados pelas atividades rotineiras de detonação representam uma preocupação para as mineradoras, que enfrentam o desafio de produzir sem causar danos críticos às barragens de rejeitos, taludes de cava e pilhas de estéril. Poucas barragens no Brasil são monitoradas por sistemas microssísmicos e não há referências na literatura sobre monitoramento em cava e barragem. Para analisar os dados dos ground motions causados pelas detonações e a sua relação com a estabilidade de uma barragem, foi instalado um sistema de monitoramento sísmico, que registra eventos continuamente num arranjo de 16 geofones (14 Hz e 4,5 Hz), instalados 12 na cava e 4 na barragem, com medição de valores de Peak Ground Acceleration, Peak Ground Velocity, frequência dominante e parâmetros da fonte sísmica dos desmontes. No período monitorado, quando foram analisados os sensores da mina e da barragem, todas as acelerações mostraram que ∼95% dos valores são menores que 0,06 m/s2, com 90% dos registros com maior frequência dominante (> 10 Hz), que apresenta menor potencial de dano devido à menor capacidade de produzir altos valores de deslocamentos. O sistema mostrou potencial para agregar novos dados e informações à atual instrumentação geotécnica da barragem.Palavras-chave: sismicidade induzida por desmontes, monitoramento microssísmico, barragem de rejeitos, gerenciamento de risco, plano de monitoramento geotécnico.
- Open Access
- 17 December 2019
- Published by Sociedade Brasileira de Geofisica in Brazilian Journal of Geophysics
- Vol. 37 (4) , 343-248
Geoelectrical Signatures and their Relationships with the Lateritic Horizons: A Case Study of the N4EN Mine’s Iron Cave, Carajás Complex, Brazil
GEOELECTRICAL SIGNATURES AND THEIR RELATIONSHIPS WITH THE LATERITIC HORIZONS: A CASE STUDY OF THE N4EN MINE’S IRON CAVE, CARAJÁS COMPLEX, BRAZIL
- 17 December 2019
- Published by Sociedade Brasileira de Geofisica in Brazilian Journal of Geophysics
- Vol. 37 (4) , 343-248
Open AccessGeoelectrical Signatures and their Relationships with the Lateritic Horizons: A Case Study of the N4EN Mine’s Iron Cave, Carajás Complex, Brazil
GEOELECTRICAL SIGNATURES AND THEIR RELATIONSHIPS WITH THE LATERITIC HORIZONS: A CASE STUDY OF THE N4EN MINE’S IRON CAVE, CARAJÁS COMPLEX, BRAZIL
- 6 December 2019
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 85 (1) , B1-B7
Electrical resistivity contrasts in the geotechnical assessment of iron caves, N4EN mine, Carajás, Brazil
Although environmental laws and regulations vary among countries regarding natural caves near mine operations, all caves require studies for safety, preservation, and/or operational licensing purposes. Therefore, understanding the cave’s stability features and their risks of collapse are important considerations for mining companies. A near-surface electric resistivity survey applied to natural caves in the surroundings of an iron mine in Carajás, state of Pará, Brazil, identified three electrical patterns as indicative of points/zones of cave ceiling lithostructural weaknesses and instabilities: (1) low-resistivity contrast, in which the signatures abruptly pass to a low resistivity (2718 ohm-m), (2) high-intermediate resistivity contrast, a transition zone at the edge of the cave between a high resistivity at the center of the cave and a resistivity of approximately 900 ohm-m in the background, and (3) angular-resistivity contrast, a zone in which the section indicates vertical geometric patterns. We found five examples of these types of anomalies. When mining operations occurred closer to a known cave, a total of 15 rock falls were mapped. We found that 11 of these (73%) had geoelectrical anomalies similar to the patterns that we identified. These results contribute to improving the predictability of cave damage and its monitoring issues in which caves should be preserved during mining operations in their vicinity.
- 6 December 2019
- Published by Society of Exploration Geophysicists in Geophysics
- Vol. 85 (1) , B1-B7
Electrical resistivity contrasts in the geotechnical assessment of iron caves, N4EN mine, Carajás, Brazil
Although environmental laws and regulations vary among countries regarding natural caves near mine operations, all caves require studies for safety, preservation, and/or operational licensing purposes. Therefore, understanding the cave’s stability features and their risks of collapse are important considerations for mining companies. A near-surface electric resistivity survey applied to natural caves in the surroundings of an iron mine in Carajás, state of Pará, Brazil, identified three electrical patterns as indicative of points/zones of cave ceiling lithostructural weaknesses and instabilities: (1) low-resistivity contrast, in which the signatures abruptly pass to a low resistivity (2718 ohm-m), (2) high-intermediate resistivity contrast, a transition zone at the edge of the cave between a high resistivity at the center of the cave and a resistivity of approximately 900 ohm-m in the background, and (3) angular-resistivity contrast, a zone in which the section indicates vertical geometric patterns. We found five examples of these types of anomalies. When mining operations occurred closer to a known cave, a total of 15 rock falls were mapped. We found that 11 of these (73%) had geoelectrical anomalies similar to the patterns that we identified. These results contribute to improving the predictability of cave damage and its monitoring issues in which caves should be preserved during mining operations in their vicinity.
- Open Access
- 1 December 2019
- Published by Sociedade Brasileira de Geofisica in Revista Brasileira de Geofísica
- Vol. 37 (4) , 489-502
WELL LOGGING APPLIED TO FERRUGINOUS KARST TERRAINS INVESTIGATION, CARAJÁS – PA, BRAZIL
Karst terrains and landforms (caves) are common features near N4EN iron mine, Carajás, Pará State, Brazil. These domains are associated to a combination of weathering plus dissolution processes in rocks. So, both processes lead to the development of a weathering profile. In N4EN mine, the dissolved rocks have ferruginous composition and may be associated to iron ore. Therefore, the weathering profile is composed by lateritic horizons. In Brazilian constitution, mining sites can’t operate nearby caves before performing a preliminary technical-scientific investigation. Because of this scenario, a pilot project was designed with the purpose to apply geological-geotechnical and geophysical (electroresistivity, ground penetrating radar and well logging) methods in karst investigation. This pilot methodology was first applied to N4E-0026 cave, in N4EN mine, and its surroundings. This article is focused on interpretation of the well logging results and aims to: (1) analyse petrophysical properties (density and natural radioactivity) of rocks nearby N4EN-0026 cave; and (2) identify and explain trends for rock’s petrophysical properties. Therefore, within logging data it was feasible to calculate the average density of rocks, identify elements associated to density variation and prove the effectiveness of well logging providing quantitative information. Keywords: applied geophysics, geophysical well logging, speleological geophysics, near surface geophysics. RESUMO. Relevos e estruturas cársticas (cavidades) são estruturas comuns na mina de ferro N4EN, Carajás, Pará, Brasil. Tais regiões estão relacionadas a uma interação entre processos de alteração intempérica e dissolução. Na mina N4EN, as rochas alteradas têm composição ferruginosa e podem estar associadas ao minério de ferro. Desse modo, esta combinação resulta no desenvolvimento de um perfil de alteração, de composição laterítica. De acordo com a constituição brasileira, empreendimentos mineiros não podem atuar próximo de cavidades até que seja feita uma investigação técnico-científica. Portanto, foi proposto um projeto piloto destinado a pesquisa de terrenos cársticos através de uma abordagem geológica, geotécnica e geofísica (eletrorresistividade, radar de penetração e perfilagem geofísica). O primeiro alvo desta metodologia pioneira foi a cavidade N4EN-0026, na mina N4EN, e sua área de influência. Este artigo versa sobre a interpretação dos dados de perfilagem geofísica e tem por objetivo: (1) analisar propriedades petrofísicas (densidade e radioatividade natural) de rochas próximas da cavidade N4EN-0026; e (2) identificar e explicar o comportamento das propriedades petrofísicas. Através dos resultados de perfilagem geofísica pôde-se: calcular a densidade média das rochas, identificar causas para variações de densidade e atestar a aplicabilidade da perfilagem geofísica para obtenção de dados quantitativos. Palavras-chave: geofísica aplicada, perfilagem geofísica, geofísica espeleológica, geofísica rasa.
- 1 December 2019
- Published by Sociedade Brasileira de Geofisica in Revista Brasileira de Geofísica
- Vol. 37 (4) , 489-502
Open AccessWELL LOGGING APPLIED TO FERRUGINOUS KARST TERRAINS INVESTIGATION, CARAJÁS – PA, BRAZIL
Karst terrains and landforms (caves) are common features near N4EN iron mine, Carajás, Pará State, Brazil. These domains are associated to a combination of weathering plus dissolution processes in rocks. So, both processes lead to the development of a weathering profile. In N4EN mine, the dissolved rocks have ferruginous composition and may be associated to iron ore. Therefore, the weathering profile is composed by lateritic horizons. In Brazilian constitution, mining sites can’t operate nearby caves before performing a preliminary technical-scientific investigation. Because of this scenario, a pilot project was designed with the purpose to apply geological-geotechnical and geophysical (electroresistivity, ground penetrating radar and well logging) methods in karst investigation. This pilot methodology was first applied to N4E-0026 cave, in N4EN mine, and its surroundings. This article is focused on interpretation of the well logging results and aims to: (1) analyse petrophysical properties (density and natural radioactivity) of rocks nearby N4EN-0026 cave; and (2) identify and explain trends for rock’s petrophysical properties. Therefore, within logging data it was feasible to calculate the average density of rocks, identify elements associated to density variation and prove the effectiveness of well logging providing quantitative information. Keywords: applied geophysics, geophysical well logging, speleological geophysics, near surface geophysics. RESUMO. Relevos e estruturas cársticas (cavidades) são estruturas comuns na mina de ferro N4EN, Carajás, Pará, Brasil. Tais regiões estão relacionadas a uma interação entre processos de alteração intempérica e dissolução. Na mina N4EN, as rochas alteradas têm composição ferruginosa e podem estar associadas ao minério de ferro. Desse modo, esta combinação resulta no desenvolvimento de um perfil de alteração, de composição laterítica. De acordo com a constituição brasileira, empreendimentos mineiros não podem atuar próximo de cavidades até que seja feita uma investigação técnico-científica. Portanto, foi proposto um projeto piloto destinado a pesquisa de terrenos cársticos através de uma abordagem geológica, geotécnica e geofísica (eletrorresistividade, radar de penetração e perfilagem geofísica). O primeiro alvo desta metodologia pioneira foi a cavidade N4EN-0026, na mina N4EN, e sua área de influência. Este artigo versa sobre a interpretação dos dados de perfilagem geofísica e tem por objetivo: (1) analisar propriedades petrofísicas (densidade e radioatividade natural) de rochas próximas da cavidade N4EN-0026; e (2) identificar e explicar o comportamento das propriedades petrofísicas. Através dos resultados de perfilagem geofísica pôde-se: calcular a densidade média das rochas, identificar causas para variações de densidade e atestar a aplicabilidade da perfilagem geofísica para obtenção de dados quantitativos. Palavras-chave: geofísica aplicada, perfilagem geofísica, geofísica espeleológica, geofísica rasa.