Mattia Guglielmi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Mattia Guglielmi has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
Egbert Baake
2 shared publications- Ali Ashrafizadeh
Faculty of Mechanical Engineering, K. N. Toosi University of Technology, Tehran P.O.B. 19395-1999, Iran
1 shared publication - Angelo Tonello
Department of Industrial Engineering, University of Padua, via G. Gradenigo 6/a, 35131 Padua, PD, Italy
1 shared publication - Davide Iosa
Continuus-Properzi S.p.A., via Emilia km 310, 26858 Sordio, LO, Italy
1 shared publication - Elisa Holzmann
Institut für Werkstoffkunde (Materials Science), Leibniz Universität Hannover, Garbsen, Germany
1 shared publication - Giovanni Pirovano
Continuus-Properzi S.p.A., via Emilia km 310, 26858 Sordio, LO, Italy
1 shared publication
Latest Publications
- Open Access
Innovative Electromagnetic Stirring Technologies for Wheel and Belt Continuous Casting Process
Electromagnetic stirring is an established strategy for improving the quality of continuously cast metals. In thin aluminium slabs, however, its implementation is constrained by short solidification length, limited installation space, and magnetic-field distortion caused by surrounding metallic components. This work presents a staged design assessment of three compact electromagnetic stirring configurations conceived for the Wheel and Belt continuous casting line of Continuus-Properzi S.p.A. Harmonic electromagnetic simulations were performed for all three configurations, whereas a coupled steady-state, isothermal electromagnetic–fluid-dynamic analysis, based on a fully liquid melt assumption, was carried out only for the axial-flux configuration. Qualitative experiments on a low-melting-point GaInSn alloy were used as proof-of-concept support for the predicted stirring patterns, rather than as a full quantitative validation of the industrial process. Because the three configurations were investigated at different levels and under different operating conditions, the results do not establish a quantitative performance ranking. The axial-flux configuration was selected for further development based on its compactness, integration feasibility, and the circular flow topology obtained numerically and observed qualitatively. Future work will focus on quantitative velocity measurements, transient and thermo-solidification modelling, and industrial-scale validation.
Open AccessInnovative Electromagnetic Stirring Technologies for Wheel and Belt Continuous Casting Process
Electromagnetic stirring is an established strategy for improving the quality of continuously cast metals. In thin aluminium slabs, however, its implementation is constrained by short solidification length, limited installation space, and magnetic-field distortion caused by surrounding metallic components. This work presents a staged design assessment of three compact electromagnetic stirring configurations conceived for the Wheel and Belt continuous casting line of Continuus-Properzi S.p.A. Harmonic electromagnetic simulations were performed for all three configurations, whereas a coupled steady-state, isothermal electromagnetic–fluid-dynamic analysis, based on a fully liquid melt assumption, was carried out only for the axial-flux configuration. Qualitative experiments on a low-melting-point GaInSn alloy were used as proof-of-concept support for the predicted stirring patterns, rather than as a full quantitative validation of the industrial process. Because the three configurations were investigated at different levels and under different operating conditions, the results do not establish a quantitative performance ranking. The axial-flux configuration was selected for further development based on its compactness, integration feasibility, and the circular flow topology obtained numerically and observed qualitatively. Future work will focus on quantitative velocity measurements, transient and thermo-solidification modelling, and industrial-scale validation.
- Open Access
- 22 November 2024
- Published by Elsevier in Intermetallics
- Vol. 176
Enhanced mechanical properties of Nb-18.7Si alloy by addition of ceramic nano particles for microstructural control
- 22 November 2024
- Published by Elsevier in Intermetallics
- Vol. 176
Open AccessEnhanced mechanical properties of Nb-18.7Si alloy by addition of ceramic nano particles for microstructural control
- 20 August 2022
- Published by Elsevier in Journal of Food Engineering
- Vol. 338
Effects of thermal boundary conditions on the performance of spray dryers
- 20 August 2022
- Published by Elsevier in Journal of Food Engineering
- Vol. 338
Effects of thermal boundary conditions on the performance of spray dryers