Vladyslav Kyrnats
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Vladyslav Kyrnats has a total of 25 co-authors. Here are the top co-authors by number of shared publications:
- Dmytro Minchev
Odesa National Maritime University , Odesa , Ukraine
3 shared publications - Roman Varbanets
Odesa National Maritime University , Odesa , Ukraine
3 shared publications - Vitalii Zalozh
Дунайський інститут Національного університету «Одеська морська академія
2 shared publications - A. P. Marchenko
National technical university «Kharkiv polytechnic institute
1 shared publication Aleksandrovska Nadiia
Department of Shipbuilding and Ship Repair named after Prof. Yu.L. Vorobyov Odesa National Maritime University , Odesa , Ukraine
1 shared publication- Artur Zaporozhets
General Energy Institute of National Academy of Sciences of Ukraine, Kyiv, Ukraine; International Institute for Applied Systems Analysis, Laxenburg, Austria, Ukraine
1 shared publication
Latest Publications
- 14 July 2026
- Published by Springer Nature
- p. 55-66
Environmental Challenges and Solutions for Fuel Optimization and Emission Control in Modern Shipping
- 14 July 2026
- Published by Springer Nature
- p. 55-66
Environmental Challenges and Solutions for Fuel Optimization and Emission Control in Modern Shipping
- Open Access
- 6 May 2026
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 33 (2) , 122-133
Condition Diagnostics of Marine Centrifugal Pumps Based on Blade-Passing Frequency Harmonics with Analytical DFT Leakage Compensation
The reliable operation of high-power marine centrifugal pumps is critical for the safety and efficiency of ballast and fire-fighting systems, as well as for the functioning of a wide range of power and auxiliary installations on large ocean-going vessels. This paper presents a vibrodiagnostic method for the condition monitoring of a vertical in-line marine centrifugal pump manufactured by DESMI, based on the frequency-domain analysis of vibration signals measured in the impeller zone. The paper focuses on the study of discrete amplitude spectra obtained under steady-state operating conditions at a rotational speed close to 900 rpm. Particular attention is paid to the distortion of diagnostic features caused by spectral leakage of the fundamental rotational harmonic, which significantly affects the identification of key diagnostic parameters. An analytical procedure for compensating the power leakage of the central harmonic is proposed, enabling accurate reconstruction of the true spectral energy distribution without increasing the measurement record length or applying complex windowing techniques. The proposed approach improves the resolution and interpretability of vibration spectra within the operating frequency range of the pump. The method enhances the reliability of vibration-based condition monitoring for marine centrifugal pumps operating under real shipboard conditions and can be implemented in existing condition-based maintenance systems without additional hardware modification. Moreover, a procedure for a continuous vibration monitoring system for a high-power centrifugal pump, suitable for integration into modern controllers with FFT functionality, is developed. The results demonstrate that the proposed analytical compensation of spectral leakage is an effective tool for improving the vibrodiagnostic reliability of high-power shipboard pumps and supports the early detection of hydraulic and mechanical degradation in critical auxiliary marine machinery.
- 6 May 2026
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 33 (2) , 122-133
Open AccessCondition Diagnostics of Marine Centrifugal Pumps Based on Blade-Passing Frequency Harmonics with Analytical DFT Leakage Compensation
The reliable operation of high-power marine centrifugal pumps is critical for the safety and efficiency of ballast and fire-fighting systems, as well as for the functioning of a wide range of power and auxiliary installations on large ocean-going vessels. This paper presents a vibrodiagnostic method for the condition monitoring of a vertical in-line marine centrifugal pump manufactured by DESMI, based on the frequency-domain analysis of vibration signals measured in the impeller zone. The paper focuses on the study of discrete amplitude spectra obtained under steady-state operating conditions at a rotational speed close to 900 rpm. Particular attention is paid to the distortion of diagnostic features caused by spectral leakage of the fundamental rotational harmonic, which significantly affects the identification of key diagnostic parameters. An analytical procedure for compensating the power leakage of the central harmonic is proposed, enabling accurate reconstruction of the true spectral energy distribution without increasing the measurement record length or applying complex windowing techniques. The proposed approach improves the resolution and interpretability of vibration spectra within the operating frequency range of the pump. The method enhances the reliability of vibration-based condition monitoring for marine centrifugal pumps operating under real shipboard conditions and can be implemented in existing condition-based maintenance systems without additional hardware modification. Moreover, a procedure for a continuous vibration monitoring system for a high-power centrifugal pump, suitable for integration into modern controllers with FFT functionality, is developed. The results demonstrate that the proposed analytical compensation of spectral leakage is an effective tool for improving the vibrodiagnostic reliability of high-power shipboard pumps and supports the early detection of hydraulic and mechanical degradation in critical auxiliary marine machinery.
- Open Access
- 31 December 2025
- Published by Kherson National Technical University in Вісник Херсонського національного технічного університету
- Vol. 1 (4(95)) , 180-185
ВПЛИВ КОНСТРУКТИВНИХ І ТЕХНОЛОГІЧНИХ ОСОБЛИВОСТЕЙ СУДЕН НА ОРГАНІЗАЦІЮ МАШИННОЇ ВАХТИ
У сучасній транспортній системі якість організації машинної вахти безпосередньо впливає на безпеку та ритмічність перевізного процесу, особливо в умовах мультимодальних перевезень, де морський сегмент має бути узгоджений із вимогами портових інфраструктур, логістичних операторів і міжнародних регуляторів. Конструктивні та технологічні особливості різних типів суден (контейнеровозів, балкерів, танкерів і газовозів) формують різні моделі технічного навантаження на екіпаж, що підсилюється потребою дотримання міжнародних екологічних і безпекових норм. Метою статті є формування рекомендацій щодо вдосконалення організації машинної вахти з урахуванням конструктивно-технологічних параметрів морських суден, особливостей їх експлуатації і ролі у мультимодальних ланцюгах постачання. Методологічну основу дослідження становлять порівняльний аналіз технічних характеристик енергетичних установок, структурно-функціональний підхід до оцінювання вахтових процесів, а також критичний огляд нормативних вимог, що регламентують діяльність машинної команди в міжнародному та національному морському праві. Отримані результати демонструють, що конструктивні рішення (тип двигуна, архітектура енергетичної установки, спеціалізовані вантажні системи) безпосередньо визначають інтенсивність контролю та профілактики, яку здійснює машинна вахта, тоді як логістичні умови мультимодальних перевезень формують вимоги до точності виконання процедур, синхронізації із портовими розкладами та підтримання технічної готовності судна. Сформовані рекомендації охоплюють напрями посилення профілактичного контролю, оптимізації взаємодії між машинною вахтою та логістичними службами, а також модернізації процедур відповідно до вимог технічного регулювання. Узагальнення результатів дозволяє стверджувати, що ефективне управління машинною вахтою можливе лише за умови інтеграції технічних, нормативних і логістичних чинників в єдиний механізм організації вахтової діяльності. Перспективи подальших досліджень пов’язані з удосконаленням цифрових інструментів для моніторингу технічних параметрів, оцінюванням ризиків відмов у мультимодальних ланцюгах і розширенням практик інтеграції логістичних і технічних систем управління вахтовою діяльністю.
- 31 December 2025
- Published by Kherson National Technical University in Вісник Херсонського національного технічного університету
- Vol. 1 (4(95)) , 180-185
Open AccessВПЛИВ КОНСТРУКТИВНИХ І ТЕХНОЛОГІЧНИХ ОСОБЛИВОСТЕЙ СУДЕН НА ОРГАНІЗАЦІЮ МАШИННОЇ ВАХТИ
У сучасній транспортній системі якість організації машинної вахти безпосередньо впливає на безпеку та ритмічність перевізного процесу, особливо в умовах мультимодальних перевезень, де морський сегмент має бути узгоджений із вимогами портових інфраструктур, логістичних операторів і міжнародних регуляторів. Конструктивні та технологічні особливості різних типів суден (контейнеровозів, балкерів, танкерів і газовозів) формують різні моделі технічного навантаження на екіпаж, що підсилюється потребою дотримання міжнародних екологічних і безпекових норм. Метою статті є формування рекомендацій щодо вдосконалення організації машинної вахти з урахуванням конструктивно-технологічних параметрів морських суден, особливостей їх експлуатації і ролі у мультимодальних ланцюгах постачання. Методологічну основу дослідження становлять порівняльний аналіз технічних характеристик енергетичних установок, структурно-функціональний підхід до оцінювання вахтових процесів, а також критичний огляд нормативних вимог, що регламентують діяльність машинної команди в міжнародному та національному морському праві. Отримані результати демонструють, що конструктивні рішення (тип двигуна, архітектура енергетичної установки, спеціалізовані вантажні системи) безпосередньо визначають інтенсивність контролю та профілактики, яку здійснює машинна вахта, тоді як логістичні умови мультимодальних перевезень формують вимоги до точності виконання процедур, синхронізації із портовими розкладами та підтримання технічної готовності судна. Сформовані рекомендації охоплюють напрями посилення профілактичного контролю, оптимізації взаємодії між машинною вахтою та логістичними службами, а також модернізації процедур відповідно до вимог технічного регулювання. Узагальнення результатів дозволяє стверджувати, що ефективне управління машинною вахтою можливе лише за умови інтеграції технічних, нормативних і логістичних чинників в єдиний механізм організації вахтової діяльності. Перспективи подальших досліджень пов’язані з удосконаленням цифрових інструментів для моніторингу технічних параметрів, оцінюванням ризиків відмов у мультимодальних ланцюгах і розширенням практик інтеграції логістичних і технічних систем управління вахтовою діяльністю.
- Open Access
- 1 December 2022
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 29 (4) , 88-96
Concept of Vibroacoustic Diagnostics of the Fuel Injection and Electronic Cylinder Lubrication Systems of Marine Diesel Engines
Although direct measurements of the fuel injection pressure and the travel of the injector needle in conjunction with measurements of the valve train mechanism timing can provide complete diagnostic information about the technical conditions of the fuel injection and valve train systems, this requires the installation of sensors and other equipment directly into the systems, which is possible within research laboratories but is generally forbidden during operation of the ship. Malfunctions in the fuel injection and valve train systems can also be identified from the indicator diagrams of an engine operating cycle, expressed as P(V) and P(deg) diagrams. The basic parameters of the engine operating cycle, such as the maximum combustion pressure Pmax, compression pressure Pcompr, and indicated mean effective pressure IMEP, can also be used to indicate deviations from proper engine operation. Using a combination of a vibration sensor with an in-cylinder gas pressure sensor widens the capabilities of diagnostics for marine diesel engines under operational conditions. A vibration sensor with a magnetic base can help in determining the timings of the lifting and landing of the injector needle, fuel delivery by the fuel injection pump, opening and closing of the circulation of heated heavy fuel oil, and opening and closing of the gas distribution valves. This also offers a promising solution for diagnostics of the cylinder lubrication oil injectors. The proposed approach allows valuable information to be received during engine operation in accordance with the principle of non-destructive control, and can help in early detection of possible engine malfunctions.
- 1 December 2022
- Published by Walter de Gruyter GmbH in Polish Maritime Research
- Vol. 29 (4) , 88-96
Open AccessConcept of Vibroacoustic Diagnostics of the Fuel Injection and Electronic Cylinder Lubrication Systems of Marine Diesel Engines
Although direct measurements of the fuel injection pressure and the travel of the injector needle in conjunction with measurements of the valve train mechanism timing can provide complete diagnostic information about the technical conditions of the fuel injection and valve train systems, this requires the installation of sensors and other equipment directly into the systems, which is possible within research laboratories but is generally forbidden during operation of the ship. Malfunctions in the fuel injection and valve train systems can also be identified from the indicator diagrams of an engine operating cycle, expressed as P(V) and P(deg) diagrams. The basic parameters of the engine operating cycle, such as the maximum combustion pressure Pmax, compression pressure Pcompr, and indicated mean effective pressure IMEP, can also be used to indicate deviations from proper engine operation. Using a combination of a vibration sensor with an in-cylinder gas pressure sensor widens the capabilities of diagnostics for marine diesel engines under operational conditions. A vibration sensor with a magnetic base can help in determining the timings of the lifting and landing of the injector needle, fuel delivery by the fuel injection pump, opening and closing of the circulation of heated heavy fuel oil, and opening and closing of the gas distribution valves. This also offers a promising solution for diagnostics of the cylinder lubrication oil injectors. The proposed approach allows valuable information to be received during engine operation in accordance with the principle of non-destructive control, and can help in early detection of possible engine malfunctions.
- Open Access
- 15 November 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Internal Combustion Engines
- No. 2,p. 51-55
IMPROVMENT OF ENVIRONMENTAL PERFORMANCE TWO-STROKE DIESEL DURING OPERATION
Розвиток світового судноплавства відбувається за умов вимог, що постійно посилюються, щодо зменшення концентрацій токсичних складових газоподібних продуктів згоряння вуглеводневих палив. Межі концентрацій цих речовин регламентуються відповідно з додатком VI Конвенції MARPOL 73/78. Серед контрольованих компонентів відпрацьованих газів дизеля найнебезпечнішими для людей та довкілля є оксиди азоту. Проте зменшення вмісту оксидів азоту неминуче пов'язані з обмеженнями максимальної температури циклу, тобто термічного ККД, отже, і з погіршенням паливної економічності двигуна. На даний момент з метою зменшення викидів оксидів азоту великими транспортними дизелями найширше застосовується рециркуляція відпрацьованих газів у повітряний ресивер. Істотним недоліком застосування цієї схеми є необхідність охолодження відпрацьованих газів та їх додаткового очищення, що призводить до збільшення масогабаритних характеристик системи та її здорожчання. Тому для здешевлення логічним виглядає поєднання рециркуляції відпрацьованих газів з іншими способами зменшення викидів оксидів азоту. Для двигунів, що вже експлуатуються, одним з таких способів виглядає зміна кута впорскування палива: відомо, що чим пізніше після верхньої мертвої точки (ВМТ) почнеться згоряння палива, тим нижче внаслідок падіння температури повітряного заряду буде кількість оксидів азоту, що утворилися. Розрахунок викидів оксидів азоту був змодельований для головного двигуна MAN-B&W 7S50MC-С, встановленого на судні "LILA SHANGHAI". Спочатку модель, створена із застосуванням пакета AVL-BOOST, була верифікована, виходячи з результатів індиціювання. Після верифікації було здійснено розрахунок викидів оксидів азоту NOx при варіації кута початку згоряння палива в номінальному режимі. Склад газів у ресивері приймався незмінним. При зсуві кута початку згоряння палива далі від ВМТ спостерігалося погіршення паливної економічності та падіння циліндрової потужності при одночасному зменшенні маси оксидів азоту NOx, що викидаються. Тим не менш, можна сказати, що екологічність двигуна покращується набагато швидше, ніж погіршуються його потужно-економічні характеристики. Наведені розрахунки показують, що для двигунів, які вже перебувають в експлуатації, зміна кута впорскування палива дозволяє зменшити викиди оксидів азоту. Тому даний підхід без особливих труднощів можна поєднувати з іншими методами, здешевлюючи таким чином екологічне вдосконалення двигуна.
- 15 November 2022
- Published by National Technical University Kharkiv Polytechnic Institute in Internal Combustion Engines
- No. 2,p. 51-55
Open AccessIMPROVMENT OF ENVIRONMENTAL PERFORMANCE TWO-STROKE DIESEL DURING OPERATION
Розвиток світового судноплавства відбувається за умов вимог, що постійно посилюються, щодо зменшення концентрацій токсичних складових газоподібних продуктів згоряння вуглеводневих палив. Межі концентрацій цих речовин регламентуються відповідно з додатком VI Конвенції MARPOL 73/78. Серед контрольованих компонентів відпрацьованих газів дизеля найнебезпечнішими для людей та довкілля є оксиди азоту. Проте зменшення вмісту оксидів азоту неминуче пов'язані з обмеженнями максимальної температури циклу, тобто термічного ККД, отже, і з погіршенням паливної економічності двигуна. На даний момент з метою зменшення викидів оксидів азоту великими транспортними дизелями найширше застосовується рециркуляція відпрацьованих газів у повітряний ресивер. Істотним недоліком застосування цієї схеми є необхідність охолодження відпрацьованих газів та їх додаткового очищення, що призводить до збільшення масогабаритних характеристик системи та її здорожчання. Тому для здешевлення логічним виглядає поєднання рециркуляції відпрацьованих газів з іншими способами зменшення викидів оксидів азоту. Для двигунів, що вже експлуатуються, одним з таких способів виглядає зміна кута впорскування палива: відомо, що чим пізніше після верхньої мертвої точки (ВМТ) почнеться згоряння палива, тим нижче внаслідок падіння температури повітряного заряду буде кількість оксидів азоту, що утворилися. Розрахунок викидів оксидів азоту був змодельований для головного двигуна MAN-B&W 7S50MC-С, встановленого на судні "LILA SHANGHAI". Спочатку модель, створена із застосуванням пакета AVL-BOOST, була верифікована, виходячи з результатів індиціювання. Після верифікації було здійснено розрахунок викидів оксидів азоту NOx при варіації кута початку згоряння палива в номінальному режимі. Склад газів у ресивері приймався незмінним. При зсуві кута початку згоряння палива далі від ВМТ спостерігалося погіршення паливної економічності та падіння циліндрової потужності при одночасному зменшенні маси оксидів азоту NOx, що викидаються. Тим не менш, можна сказати, що екологічність двигуна покращується набагато швидше, ніж погіршуються його потужно-економічні характеристики. Наведені розрахунки показують, що для двигунів, які вже перебувають в експлуатації, зміна кута впорскування палива дозволяє зменшити викиди оксидів азоту. Тому даний підхід без особливих труднощів можна поєднувати з іншими методами, здешевлюючи таким чином екологічне вдосконалення двигуна.
- 22 August 2022
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 92-100
Діагностика паливної апаратури, приводу клапанів газорозподілу та форсунок змащення циліндрів сучасних двотактних двигунів
The application of a vibration sensor with an in-cylinder pressure sensor extends the capabilities of internal combustion engines and compressor diagnostics for various types of plants and installations, such as marine diesel engines, refrigeration piston compressors, aircraft engines. The fuel injection equipment malfunctions as valve as valve train system malfunctions could be detected from the experimental indicated diagrams P(V), P(deg) of the engine cylinder operating process as it is known. The main indicators are the following: the shape of the diagram and the parameters of working cycle – the maximum combustion pressure Pmax, the compression pressure Pcomp, mean indicated pressure IMEP, etc. However, it should be considered that different types of malfunctions could have the same reflection on the indicated diagram. For instance, the late fuel injection and the fuel-injection equipment wear could have almost similar effects on the indicated diagram and main diagnostic parameters. Another example is the low compression pressure Pcomp, which could be caused by the cylinder or compression rings wear and by the exhaust valves wrong timing or valve leakage. It should also be mentioned that many types of malfunctions at their early stages are very difficult to detect and clarify based solely on the indicated diagrams analysis. The detection of such malfunctions usually requires the direct measurements of the fuel injection pressure and injector’s needle lift diagrams with accurate valve timing measurements. However, mentioned measurements could be performed under laboratory conditions and are difficult to apply under engine operating conditions. The vibration sensor application could be a reasonable alternative to the direct measurements, as it allows the determination of the injector’s needle lift-off and landing timing, high-pressure fuel pump cut-off and discharge timing, the preheated heavy fuel circulation start/stop timing as well as gas-distribution valves opening and closing timing, the oscillation frequency, and amplitude from the refrigeration system piston compressor valve operation and the cylinder oil injector timing. The vibration sensor has a magnetic basement that allows its easy mounting on the engine parts. All this information could be directly measured during engines and compressor trials by the vibration sensor applied in the advanced diagnostic systems.
- 22 August 2022
- Published by National Aerospace University - Kharkiv Aviation Institute in Aerospace technic and technology
- No. 4sup2,p. 92-100
Діагностика паливної апаратури, приводу клапанів газорозподілу та форсунок змащення циліндрів сучасних двотактних двигунів
The application of a vibration sensor with an in-cylinder pressure sensor extends the capabilities of internal combustion engines and compressor diagnostics for various types of plants and installations, such as marine diesel engines, refrigeration piston compressors, aircraft engines. The fuel injection equipment malfunctions as valve as valve train system malfunctions could be detected from the experimental indicated diagrams P(V), P(deg) of the engine cylinder operating process as it is known. The main indicators are the following: the shape of the diagram and the parameters of working cycle – the maximum combustion pressure Pmax, the compression pressure Pcomp, mean indicated pressure IMEP, etc. However, it should be considered that different types of malfunctions could have the same reflection on the indicated diagram. For instance, the late fuel injection and the fuel-injection equipment wear could have almost similar effects on the indicated diagram and main diagnostic parameters. Another example is the low compression pressure Pcomp, which could be caused by the cylinder or compression rings wear and by the exhaust valves wrong timing or valve leakage. It should also be mentioned that many types of malfunctions at their early stages are very difficult to detect and clarify based solely on the indicated diagrams analysis. The detection of such malfunctions usually requires the direct measurements of the fuel injection pressure and injector’s needle lift diagrams with accurate valve timing measurements. However, mentioned measurements could be performed under laboratory conditions and are difficult to apply under engine operating conditions. The vibration sensor application could be a reasonable alternative to the direct measurements, as it allows the determination of the injector’s needle lift-off and landing timing, high-pressure fuel pump cut-off and discharge timing, the preheated heavy fuel circulation start/stop timing as well as gas-distribution valves opening and closing timing, the oscillation frequency, and amplitude from the refrigeration system piston compressor valve operation and the cylinder oil injector timing. The vibration sensor has a magnetic basement that allows its easy mounting on the engine parts. All this information could be directly measured during engines and compressor trials by the vibration sensor applied in the advanced diagnostic systems.