Dhrubajyoti Das
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Dhrubajyoti Das has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Sreeraj Puravankara
School of Energy Science & Engineering, Indian Institute of Technology Kharagpur, Kharagpur-721302, West Bengal, India
11 shared publications - Ashwani Tyagi
Materials Science Group, Indira Gandhi Centre for Atomic Research, Kalpakkam 603102, India
2 shared publications - Debanjana Pahari
Bavarian Center for Battery Technology (BayBatt) University of Bayreuth Bayreuth Germany
2 shared publications - Rajashekar Billa
School of Energy Science & Engineering Indian Institute of Technology Kharagpur Kharagpur West Bengal India
2 shared publications - Ritupurna Baishya2 shared publications
- Sanchita Manna
School of Energy Science & Engineering Indian Institute of Technology Kharagpur Kharagpur West Bengal India
2 shared publications
Latest Publications
- 7 October 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 698
Anion-regulated interfacial stability in Prussian blue analog cathodes for quasi-solid-state aqueous sodium-ion batteries
- 7 October 2026
- Published by Elsevier in Journal of Power Sources
- Vol. 698
Anion-regulated interfacial stability in Prussian blue analog cathodes for quasi-solid-state aqueous sodium-ion batteries
- Open Access
- 16 August 2026
- Published by Wiley in Batteries & Supercaps
- Vol. 9 (8) , e70448
Sulfolane Co‐Solvent‐Tailored Interfacial Stability for High‐Temperature Sodium‐Ion Batteries
Designing and optimizing electrolyte compositions beyond carbonate/NaPF 6 is vital to advancing commercial sodium‐ion batteries, as electrode–electrolyte interface instability gravely affects the battery cycling stability and rate performance. Sulfones are known as high‐voltage solvents/additives in commercial lithium‐ion batteries. Here, sulfolane has been used as a cosolvent with a baseline electrolyte containing 1 M NaPF 6 in EC:PC (v/v, 1:1) in SIBs to improve performance and safety metrics. The electrolyte’s oxidative stability increases with the addition of SL, which has two S═O bonds, thereby forming a robust sulfur‐rich cathode‐electrolyte interface layer. The battery metrics of the commercial oxide cathode, O3‐NaNi 0.33 Fe 0.33 Mn 0.33 O 2 , were optimized with 15 vol% sulfolane co‐solvent at high temperature (60 °C) and voltage (4.2 V) to improve rate capability and capacity retention. The optimized electrolyte retains ∼90% of its specific capacity compared to the baseline electrolyte (78%). To understand interfacial chemistry, the influence of the cosolvent on electrolyte solvation structure on the cathode interface layer was mapped. The thermostability and non‐flammability of sulfolane further enhance the safety of commercial SIBs.
- 16 August 2026
- Published by Wiley in Batteries & Supercaps
- Vol. 9 (8) , e70448
Open AccessSulfolane Co‐Solvent‐Tailored Interfacial Stability for High‐Temperature Sodium‐Ion Batteries
Designing and optimizing electrolyte compositions beyond carbonate/NaPF 6 is vital to advancing commercial sodium‐ion batteries, as electrode–electrolyte interface instability gravely affects the battery cycling stability and rate performance. Sulfones are known as high‐voltage solvents/additives in commercial lithium‐ion batteries. Here, sulfolane has been used as a cosolvent with a baseline electrolyte containing 1 M NaPF 6 in EC:PC (v/v, 1:1) in SIBs to improve performance and safety metrics. The electrolyte’s oxidative stability increases with the addition of SL, which has two S═O bonds, thereby forming a robust sulfur‐rich cathode‐electrolyte interface layer. The battery metrics of the commercial oxide cathode, O3‐NaNi 0.33 Fe 0.33 Mn 0.33 O 2 , were optimized with 15 vol% sulfolane co‐solvent at high temperature (60 °C) and voltage (4.2 V) to improve rate capability and capacity retention. The optimized electrolyte retains ∼90% of its specific capacity compared to the baseline electrolyte (78%). To understand interfacial chemistry, the influence of the cosolvent on electrolyte solvation structure on the cathode interface layer was mapped. The thermostability and non‐flammability of sulfolane further enhance the safety of commercial SIBs.
- Open Access
- 21 May 2026
- Published by Elsevier in SSRN Electronic Journal
Anion-Regulated Interfacial Stability in Prussian Blue Analog Cathodes for Quasi-Solid-State Aqueous Sodium-Ion Batteries
Quasi-solid-state gel polymer electrolytes (GPEs) offer a promising strategy to enhance the safety, mechanical robustness, and interfacial stability of aqueous sodium-ion batteries (ASIBs). In this work, carboxymethyl cellulose (CMC)-based GPEs with various sodium salts (NaClO4, NaNO3, Na2SO4, and NaOAc) reveal the role of anion chemistry and show that salt concentrations ≥2 M were necessary to retain gel integrity, with electrolyte absorption and ionic conductivity trends strongly influenced by Hofmeister-type kosmotropic/chaotropic effects. The stability of Prussian blue analog (PBA) cathode against dissolution in different GPEs is established using three-electrode and full-cell electrochemical measurements. The acetate-based electrolyte (GPE-A) demonstrated the highest electrochemical stability, maintaining an average coulombic efficiency of ~95% over 350 cycles and the lowest interfacial resistance growth. In contrast, sulfate-, nitrate-, and perchlorate-based systems showed rapid degradation, unstable cycling behavior, and pronounced cathode dissolution, as confirmed by post-cycling structural and morphological analyses. The enhanced stability of GPE-A arises from the kosmotropic nature of acetate ions, aided by the mildly basic pH of the electrolyte, which together help stabilize the Fe–CN framework and suppress interfacial degradation. The work emphasizes the critical role of electrolyte anion engineering in improving cathode stability in quasi-solid-state aqueous sodium-ion batteries.
- 21 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessAnion-Regulated Interfacial Stability in Prussian Blue Analog Cathodes for Quasi-Solid-State Aqueous Sodium-Ion Batteries
Quasi-solid-state gel polymer electrolytes (GPEs) offer a promising strategy to enhance the safety, mechanical robustness, and interfacial stability of aqueous sodium-ion batteries (ASIBs). In this work, carboxymethyl cellulose (CMC)-based GPEs with various sodium salts (NaClO4, NaNO3, Na2SO4, and NaOAc) reveal the role of anion chemistry and show that salt concentrations ≥2 M were necessary to retain gel integrity, with electrolyte absorption and ionic conductivity trends strongly influenced by Hofmeister-type kosmotropic/chaotropic effects. The stability of Prussian blue analog (PBA) cathode against dissolution in different GPEs is established using three-electrode and full-cell electrochemical measurements. The acetate-based electrolyte (GPE-A) demonstrated the highest electrochemical stability, maintaining an average coulombic efficiency of ~95% over 350 cycles and the lowest interfacial resistance growth. In contrast, sulfate-, nitrate-, and perchlorate-based systems showed rapid degradation, unstable cycling behavior, and pronounced cathode dissolution, as confirmed by post-cycling structural and morphological analyses. The enhanced stability of GPE-A arises from the kosmotropic nature of acetate ions, aided by the mildly basic pH of the electrolyte, which together help stabilize the Fe–CN framework and suppress interfacial degradation. The work emphasizes the critical role of electrolyte anion engineering in improving cathode stability in quasi-solid-state aqueous sodium-ion batteries.
- 7 January 2026
- Published by Wiley in ChemistrySelect
- Vol. 11 (1)
Fast‐Charging Single‐Crystalline O3‐NaNi 1/3 Fe 1/3 Mn 1/3 O 2 via Molten Salt Synthesis for Sodium‐Ion Batteries
O3‐type cathodes in sodium‐ion batteries (SIBs) are the most promising cathodes with higher sodium content and energy density than the P2‐type cathodes. Along with standard battery performance metrics, fast‐charging cathodes with high‐rate kinetics and cycle stability are crucial for advancement in SIB technologies. The single‐crystalline materials show improved cycling stability, and when combined with particle size control, result in high‐rate performing and long cycle life cathodes. Herein, we report a molten salt‐synthesized single‐crystalline O3‐NaNi 1/3 Fe 1/3 Mn 1/3 O 2 (NFM) cathode with control over particle size/distribution through optimized molten salt ratios. The NFM cathode obtained from a 40:1 salt ratio shows rate capabilities of 102@1C, 93@2C, 75@5C (1C = 240 mAh g −1 ), improving fast‐charging kinetics. NFM showed impressive cycling stability at 68% retention after 200 cycles at 1C, 83% at 2C, and 76% at 5C after 100 cycles. This work offers a simple molten‐salt synthesis for ∼1–2 µm‐sized single‐crystalline particles to achieve good rate capabilities through effective charge transfers and high ionic diffusion kinetics, which holds the future promise for fast charging and durable SIBs.
- 7 January 2026
- Published by Wiley in ChemistrySelect
- Vol. 11 (1)
Fast‐Charging Single‐Crystalline O3‐NaNi 1/3 Fe 1/3 Mn 1/3 O 2 via Molten Salt Synthesis for Sodium‐Ion Batteries
O3‐type cathodes in sodium‐ion batteries (SIBs) are the most promising cathodes with higher sodium content and energy density than the P2‐type cathodes. Along with standard battery performance metrics, fast‐charging cathodes with high‐rate kinetics and cycle stability are crucial for advancement in SIB technologies. The single‐crystalline materials show improved cycling stability, and when combined with particle size control, result in high‐rate performing and long cycle life cathodes. Herein, we report a molten salt‐synthesized single‐crystalline O3‐NaNi 1/3 Fe 1/3 Mn 1/3 O 2 (NFM) cathode with control over particle size/distribution through optimized molten salt ratios. The NFM cathode obtained from a 40:1 salt ratio shows rate capabilities of 102@1C, 93@2C, 75@5C (1C = 240 mAh g −1 ), improving fast‐charging kinetics. NFM showed impressive cycling stability at 68% retention after 200 cycles at 1C, 83% at 2C, and 76% at 5C after 100 cycles. This work offers a simple molten‐salt synthesis for ∼1–2 µm‐sized single‐crystalline particles to achieve good rate capabilities through effective charge transfers and high ionic diffusion kinetics, which holds the future promise for fast charging and durable SIBs.
- 17 December 2025
- Published by Wiley in Energy Technology
- Vol. 14 (1)
Enhancing SEI Stability of Hard Carbon Anodes with Low‐Solvating CPME Co‐Solvent for Wide‐Temperature Sodium‐Ion Batteries
The optimization of microstructure, surface area, defects, porosity, pore morphology, and interfacial engineering of the solid electrolyte interface (SEI) is critical in improving the battery metrics of hard carbon (HC) anodes for SIBs. Herein, cyclopentyl methyl ether (CPME), a weakly solvating and wide‐temperature‐range solvent, is employed as an alternative to ethylene carbonate (EC). In combination with HC, CPME‐PC‐based electrolytes demonstrate a high initial Coulombic efficiency (ICE) of up to 75% and superior cycling stability of 91% after 100 cycles, highlighting the potential of CPME as a co‐solvent. The reduction of CPME co‐solvent forms a more inorganic and thin SEI than EC‐generated SEI, boosting the ICE and cycling stability of the anode. The HC delivered the excellent reversible capacity of 356 mAh g −1 at the current density of 30 mA g −1 with a higher low potential plateau capacity (68%) using CPME‐PC‐based electrolyte. The low‐temperature battery metric for CPME‐PC‐based electrolytes showed ~30% added capacity and improved ICE value compared to EC‐PC‐based electrolytes. The CPME‐PC‐based electrolyte indicates close to 100% Coulombic efficiency at 10°C and 0°C, with excellent cycle stability for the HC anode. The work reports for the first time the use of greener, low‐solvating CPME in improving the reversible capacity and ICE for wide‐temperature applications of SIBs.
- 17 December 2025
- Published by Wiley in Energy Technology
- Vol. 14 (1)
Enhancing SEI Stability of Hard Carbon Anodes with Low‐Solvating CPME Co‐Solvent for Wide‐Temperature Sodium‐Ion Batteries
The optimization of microstructure, surface area, defects, porosity, pore morphology, and interfacial engineering of the solid electrolyte interface (SEI) is critical in improving the battery metrics of hard carbon (HC) anodes for SIBs. Herein, cyclopentyl methyl ether (CPME), a weakly solvating and wide‐temperature‐range solvent, is employed as an alternative to ethylene carbonate (EC). In combination with HC, CPME‐PC‐based electrolytes demonstrate a high initial Coulombic efficiency (ICE) of up to 75% and superior cycling stability of 91% after 100 cycles, highlighting the potential of CPME as a co‐solvent. The reduction of CPME co‐solvent forms a more inorganic and thin SEI than EC‐generated SEI, boosting the ICE and cycling stability of the anode. The HC delivered the excellent reversible capacity of 356 mAh g −1 at the current density of 30 mA g −1 with a higher low potential plateau capacity (68%) using CPME‐PC‐based electrolyte. The low‐temperature battery metric for CPME‐PC‐based electrolytes showed ~30% added capacity and improved ICE value compared to EC‐PC‐based electrolytes. The CPME‐PC‐based electrolyte indicates close to 100% Coulombic efficiency at 10°C and 0°C, with excellent cycle stability for the HC anode. The work reports for the first time the use of greener, low‐solvating CPME in improving the reversible capacity and ICE for wide‐temperature applications of SIBs.
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (9) , 1261
Electrolyte Design to Improve Solid Electrolyte Interphase for Sodium-Ion Batteries
Hard carbon (HC) is a suitable anode for sodium-ion batteries. However, its initial coulombic efficiency is a major drawback resulting in cell energy density loss. This issue can be tackled by designing electrolyte combinations. Increasing the salt concentrations can help the formation of a robust and well-balanced organic-inorganic electrolyte interface layer.1 Anion-derived SEI layer is developed on the electrode surface due to a change of salt concentration to a higher limit.2 The solvation structure of electrolytes also plays a vital role in SEI layer building.3 Commercial hard carbon is studied using the most common solvents, such as ethylene carbonate (EC) and propylene carbonate (PC), in the ratio of 1:1 v/v. NaClO4 and NaFSI salts are used in different concentrations. Our baseline electrolyte is 1M NaClO4 in EC: PC (1:1 v/v) which provides a capacity of 326 mAh g-1 with an ICE value of 63.3% at 0.1C rate (Fig 1a). Changing salt anion from ClO4 - to FSI- does not help improve capacity or coulombic efficiency. However, if we optimized the concentration to 3M, then the capacity would be 356 mAh g-1 with an ICE value of 73% (Fig 1b). This difference in ICE is due to stable anion-derived SEI layer formation. The oral presentation will focus on the effect of salt concentration on the battery performance of Commercial HC and Transition Metal Oxide cathode in half-cell and full-cell configurations in Na-ion batteries. Reference Y. Yamada, J. Wang, S. Ko, E. Watanabe, and A. Yamada, Nat. Energy, 4, 269–280 (2019). J. Patra et al., Energy Storage Mater., 16, 146–154 (2019). Y. Ugata et al., Phys. Chem. Chem. Phys., 23, 21419–21436 (2021).
- 22 November 2024
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2024-02 (9) , 1261
Electrolyte Design to Improve Solid Electrolyte Interphase for Sodium-Ion Batteries
Hard carbon (HC) is a suitable anode for sodium-ion batteries. However, its initial coulombic efficiency is a major drawback resulting in cell energy density loss. This issue can be tackled by designing electrolyte combinations. Increasing the salt concentrations can help the formation of a robust and well-balanced organic-inorganic electrolyte interface layer.1 Anion-derived SEI layer is developed on the electrode surface due to a change of salt concentration to a higher limit.2 The solvation structure of electrolytes also plays a vital role in SEI layer building.3 Commercial hard carbon is studied using the most common solvents, such as ethylene carbonate (EC) and propylene carbonate (PC), in the ratio of 1:1 v/v. NaClO4 and NaFSI salts are used in different concentrations. Our baseline electrolyte is 1M NaClO4 in EC: PC (1:1 v/v) which provides a capacity of 326 mAh g-1 with an ICE value of 63.3% at 0.1C rate (Fig 1a). Changing salt anion from ClO4 - to FSI- does not help improve capacity or coulombic efficiency. However, if we optimized the concentration to 3M, then the capacity would be 356 mAh g-1 with an ICE value of 73% (Fig 1b). This difference in ICE is due to stable anion-derived SEI layer formation. The oral presentation will focus on the effect of salt concentration on the battery performance of Commercial HC and Transition Metal Oxide cathode in half-cell and full-cell configurations in Na-ion batteries. Reference Y. Yamada, J. Wang, S. Ko, E. Watanabe, and A. Yamada, Nat. Energy, 4, 269–280 (2019). J. Patra et al., Energy Storage Mater., 16, 146–154 (2019). Y. Ugata et al., Phys. Chem. Chem. Phys., 23, 21419–21436 (2021).
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (1) , 123
Boosting the Initial Coulombic Efficiency of Sustainable Hard Carbon Derived from Polyethylene Terephthalate with Cyclopentyl Methyl Ether As a Co-Solvent for Wide-Temperature Sodium-Ion Batteries
Upcycling plastic waste into value-added products helps to generate cost-effective and sustainable resources towards a circular materials economy and safer ecosystem. The conversion of polyethylene terephthalate (PET) municipal waste via the carbonization process into hard carbon (HC) delivers a high-reversible capacity, low-cost, sustainable anode material for sodium-ion batteries (SIBs). However, the low initial Coulombic efficiency (ICE) is a significant challenge of the HC anode, which should be optimized by electrolyte and interfacial chemistry.1 In conventional carbonate esters-based electrolytes, ethylene carbonate (EC) forms an organic-rich thick SEI layer, soluble on cycling, limiting the cyclic stability. The low-temperature performance is also a significant concern in achieving high capacity, long cyclability, and ICE.2 Herein, HC derived via single-step carbonization at 1000℃ exhibits larger interlayer spacing of 0.379 nm, low surface area (~205 m2g-1), and unique slit-shaped pores with 84% mesoporosity in the structure. PET-HC exhibits a high reversible capacity of 337 mAh g-1 with ICE of just 66%, using EC-PC-based electrolyte. EC-free cyclopentyl methyl ether (CPME) was used due to its weakly solvating and wide temperature solvent.3 CPME-PC-based electrolytes significantly enhanced the ICE value to 74.5% and reversible capacity to 356 mAh g-1 with superior cycling of 91% after 100 cycles at 0.1C rate. The inorganic-rich SEI layer for CPME-PC-based electrolytes results in a thin SEI that improves the ICE and cyclic stability of the anode. The low-temperature performance (up to -20°C) for CPME-PC-based electrolytes showed ~30% added capacity compared to EC-PC-based electrolytes. This work provided an eco-friendly approach to developing hard carbons from plastic trash and offered an effective strategy to replace EC with CPME for low-temperature sodium storage applications. References Shen, L., Shi, S., Roy, S., Yin, X., Liu, W., Zhao, Y., Adv. Funct. Mater. 2021, 31, 2006066. Ramasamy, H. V., Kim, S., Adams, E. J., Rao, H. & Pol, V. G. Chem. Commun. 2022, 58, 5124–5127. Zhang, H., Zeng, Z., Ma, F., Wu, Q., Wang, X., Cheng, S., Xie, J., Angew. Chem. 2023, e202300771. Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (1) , 123
Boosting the Initial Coulombic Efficiency of Sustainable Hard Carbon Derived from Polyethylene Terephthalate with Cyclopentyl Methyl Ether As a Co-Solvent for Wide-Temperature Sodium-Ion Batteries
Upcycling plastic waste into value-added products helps to generate cost-effective and sustainable resources towards a circular materials economy and safer ecosystem. The conversion of polyethylene terephthalate (PET) municipal waste via the carbonization process into hard carbon (HC) delivers a high-reversible capacity, low-cost, sustainable anode material for sodium-ion batteries (SIBs). However, the low initial Coulombic efficiency (ICE) is a significant challenge of the HC anode, which should be optimized by electrolyte and interfacial chemistry.1 In conventional carbonate esters-based electrolytes, ethylene carbonate (EC) forms an organic-rich thick SEI layer, soluble on cycling, limiting the cyclic stability. The low-temperature performance is also a significant concern in achieving high capacity, long cyclability, and ICE.2 Herein, HC derived via single-step carbonization at 1000℃ exhibits larger interlayer spacing of 0.379 nm, low surface area (~205 m2g-1), and unique slit-shaped pores with 84% mesoporosity in the structure. PET-HC exhibits a high reversible capacity of 337 mAh g-1 with ICE of just 66%, using EC-PC-based electrolyte. EC-free cyclopentyl methyl ether (CPME) was used due to its weakly solvating and wide temperature solvent.3 CPME-PC-based electrolytes significantly enhanced the ICE value to 74.5% and reversible capacity to 356 mAh g-1 with superior cycling of 91% after 100 cycles at 0.1C rate. The inorganic-rich SEI layer for CPME-PC-based electrolytes results in a thin SEI that improves the ICE and cyclic stability of the anode. The low-temperature performance (up to -20°C) for CPME-PC-based electrolytes showed ~30% added capacity compared to EC-PC-based electrolytes. This work provided an eco-friendly approach to developing hard carbons from plastic trash and offered an effective strategy to replace EC with CPME for low-temperature sodium storage applications. References Shen, L., Shi, S., Roy, S., Yin, X., Liu, W., Zhao, Y., Adv. Funct. Mater. 2021, 31, 2006066. Ramasamy, H. V., Kim, S., Adams, E. J., Rao, H. & Pol, V. G. Chem. Commun. 2022, 58, 5124–5127. Zhang, H., Zeng, Z., Ma, F., Wu, Q., Wang, X., Cheng, S., Xie, J., Angew. Chem. 2023, e202300771. Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (6) , 934
Redox Shuttle Additives for Sodium-Ion Batteries
Redox shuttle additives are already known in the battery field to provide overcharge protection, mainly at high-voltage cathode electrodes. The electroactive species can get either oxidized at the cathode side or reduced at the anode side, preferentially during the battery cycling. The mechanism involves the generation of positively charged radicals during oxidation and the subsequent diffusion and reduction at the anode surface. This shuttling process continues between the electrodes through baseline electrolytes. Redox shuttle additives are extensively studied in Li-ion batteries (LIBs).1–3 Benzophenone (BP) is one of the redox shuttle additives used successfully in lithium-ion batteries.4 No report exists in the literature for BP additives in sodium-ion batteries (SIBs). This work investigates BP (an already known overcharge protecting additive) and substituted 4-methyl BP (4-methyl benzophenone) as an electrolyte additive in baseline electrolyte containing NaClO4 in EC/PC solvent on both electrodes. The aim is to investigate BP's SEI-forming properties in sodium-ion batteries. The initial half-cell test with a Hard Carbon anode without and with 0.5 wt% 4-methyl BP as the additive is shown in Fig.1. 4-Methyl BP additive shows a large increase in specific capacity from 337 mAh gm-1 to 438 mAh gm-1 at 0.1C rate in a 5 mV - 1.5 V voltage range. The oral presentation will focus on the effect of additive concentration on the battery performance of HC and polyanionic cathode NVP in half-cell and full-cell configurations in Na-ion batteries. References: C. Buhrmester, L. Moshurchak, R. L. Wang, and J. R. Dahn, J. Electrochem. Soc., 153, A288 (2006). L. M. Moshurchak et al., J. Electrochem. Soc., 156, A309 (2009). M. Tang and J. Newman, J. Electrochem. Soc., 158, A530–A536 (2011). Q. Wang, S. M. Zakeeruddin, I. Exnar, and M. Grätzel, Electrochem. commun., 10, 651–654 (2008). Figure 1
- 22 December 2023
- Published by The Electrochemical Society in ECS Meeting Abstracts
- Vol. MA2023-02 (6) , 934
Redox Shuttle Additives for Sodium-Ion Batteries
Redox shuttle additives are already known in the battery field to provide overcharge protection, mainly at high-voltage cathode electrodes. The electroactive species can get either oxidized at the cathode side or reduced at the anode side, preferentially during the battery cycling. The mechanism involves the generation of positively charged radicals during oxidation and the subsequent diffusion and reduction at the anode surface. This shuttling process continues between the electrodes through baseline electrolytes. Redox shuttle additives are extensively studied in Li-ion batteries (LIBs).1–3 Benzophenone (BP) is one of the redox shuttle additives used successfully in lithium-ion batteries.4 No report exists in the literature for BP additives in sodium-ion batteries (SIBs). This work investigates BP (an already known overcharge protecting additive) and substituted 4-methyl BP (4-methyl benzophenone) as an electrolyte additive in baseline electrolyte containing NaClO4 in EC/PC solvent on both electrodes. The aim is to investigate BP's SEI-forming properties in sodium-ion batteries. The initial half-cell test with a Hard Carbon anode without and with 0.5 wt% 4-methyl BP as the additive is shown in Fig.1. 4-Methyl BP additive shows a large increase in specific capacity from 337 mAh gm-1 to 438 mAh gm-1 at 0.1C rate in a 5 mV - 1.5 V voltage range. The oral presentation will focus on the effect of additive concentration on the battery performance of HC and polyanionic cathode NVP in half-cell and full-cell configurations in Na-ion batteries. References: C. Buhrmester, L. Moshurchak, R. L. Wang, and J. R. Dahn, J. Electrochem. Soc., 153, A288 (2006). L. M. Moshurchak et al., J. Electrochem. Soc., 156, A309 (2009). M. Tang and J. Newman, J. Electrochem. Soc., 158, A530–A536 (2011). Q. Wang, S. M. Zakeeruddin, I. Exnar, and M. Grätzel, Electrochem. commun., 10, 651–654 (2008). Figure 1
- Open Access
Electrolytes, Additives and Binders for NMC Cathodes in Li-Ion Batteries—A Review
Among the current battery technologies, lithium-ion batteries (LIBs) are essential in shaping future energy landscapes in stationary storage and e-mobility. Among all components, choosing active cathode material (CAM) limits a cell’s available energy density (Wh kg−1), and the CAM selection becomes critical. Layered Lithium transition metal oxides, primarily, LiNixMnyCozO2 (NMC) (x + y + z = 1), represent a prominent class of cathode materials for LIBs due to their high energy density and capacity. The battery performance metrics of NMC cathodes vary according to the different ratios of transition metals in the CAM. The non-electrode factors and their effect on the cathode performance of a lithium-ion battery are as significant in a commercial sense. These factors can affect the capacity, cycle lifetime, thermal safety, and rate performance of the NMC battery. Additionally, polycrystalline NMC comprises secondary clusters of primary crystalline particles prone to pulverization along the grain boundaries, which leads to microcrack formation and unwanted side reactions with the electrolyte. Single-crystal NMC (SC-NMC) morphology tackles the cycling stability issue for improved performance but falls short in enhancing capacity and rate capability. The compatibility of different combinations of electrolytes and additives for SC-NMC is discussed, considering the commercial aspects of NMC in electric vehicles. The review has targeted the recent development of non-aqueous electrolyte systems with various additives and aqueous and non-aqueous binders for NMC-based LIBs to stress their importance in the battery chemistry of NMC.
Open AccessElectrolytes, Additives and Binders for NMC Cathodes in Li-Ion Batteries—A Review
Among the current battery technologies, lithium-ion batteries (LIBs) are essential in shaping future energy landscapes in stationary storage and e-mobility. Among all components, choosing active cathode material (CAM) limits a cell’s available energy density (Wh kg−1), and the CAM selection becomes critical. Layered Lithium transition metal oxides, primarily, LiNixMnyCozO2 (NMC) (x + y + z = 1), represent a prominent class of cathode materials for LIBs due to their high energy density and capacity. The battery performance metrics of NMC cathodes vary according to the different ratios of transition metals in the CAM. The non-electrode factors and their effect on the cathode performance of a lithium-ion battery are as significant in a commercial sense. These factors can affect the capacity, cycle lifetime, thermal safety, and rate performance of the NMC battery. Additionally, polycrystalline NMC comprises secondary clusters of primary crystalline particles prone to pulverization along the grain boundaries, which leads to microcrack formation and unwanted side reactions with the electrolyte. Single-crystal NMC (SC-NMC) morphology tackles the cycling stability issue for improved performance but falls short in enhancing capacity and rate capability. The compatibility of different combinations of electrolytes and additives for SC-NMC is discussed, considering the commercial aspects of NMC in electric vehicles. The review has targeted the recent development of non-aqueous electrolyte systems with various additives and aqueous and non-aqueous binders for NMC-based LIBs to stress their importance in the battery chemistry of NMC.