Zhen Yin
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Zhen Yin has a total of 33 co-authors. Here are the top co-authors by number of shared publications:
Chenwei Dai
8 shared publicationsQing Miao
School of Mechanical Engineering, Suzhou University of Science and Technology, Suzhou, China
6 shared publicationsHua Li
5 shared publicationsDingyi Tao
School of Mechanical Engineering, Suzhou University of Science and Technology, Suzhou, China
3 shared publicationsKun Zhang
School of Mechanical Engineering, Suzhou University of Science and Technology, Suzhou, China
3 shared publicationsMengqiu Yu
School of Mechanical Engineering, Suzhou University of Science and Technology, Suzhou, China
3 shared publications
Latest Publications
- 4 August 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 146 (1-2) , 609-628
Ultrasonic-assisted deep hole grinding of alumina ceramics with laser surface micro-structured brazed diamond tools
- 4 August 2026
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 146 (1-2) , 609-628
Ultrasonic-assisted deep hole grinding of alumina ceramics with laser surface micro-structured brazed diamond tools
- 23 September 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 74
Research on removal mechanism of longitudinal-torsional compound ultrasonic vibration end grinding sapphire
- 23 September 2025
- Published by Elsevier in Surfaces and Interfaces
- Vol. 74
Research on removal mechanism of longitudinal-torsional compound ultrasonic vibration end grinding sapphire
- 28 August 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 140 (3-4) , 1963-1979
Investigation on ultrasonic vibration assisted drilling of monocrystalline silicon: exit-chipping formation mechanism and axial force analysis
- 28 August 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 140 (3-4) , 1963-1979
Investigation on ultrasonic vibration assisted drilling of monocrystalline silicon: exit-chipping formation mechanism and axial force analysis
- 19 August 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 140 (1-2) , 891-908
Prediction and suppression of exit burr height in ultrasonic vibration-assisted micro-drilling of GH4169 superalloy
- 19 August 2025
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 140 (1-2) , 891-908
Prediction and suppression of exit burr height in ultrasonic vibration-assisted micro-drilling of GH4169 superalloy
- Open Access
- 19 August 2025
- Published by Springer Nature in Research Square
Research on cutting forces and tool wear during tilted ultrasonic elliptical vibration cutting of Ti-6Al-4V
Titanium alloy has the characteristics of high strength, low thermal conductivity, high ductility, etc. When machining it by conventional process, there are problems such as high local temperature in the machining area, serious tool wear and low machining quality. In this paper, the cutting force and tool wear of TC4 titanium alloy under tilted ultrasonic elliptical vibration cutting (TUEVC) was studied by using a Suzhou Sunshines Ultrasonic Equipment. Firstly, the material removal mechanisms under the three machining modes of conventional cutting (CC), conventional ultrasonic elliptical vibration cutting (UEVC) and TUEVC were compared and analysed, as well as the influence of the tilt angle on the cutting force under ultrasonic elliptical vibration cutting. Subsequently, tool wear experiments were carried out for the three machining modes to compare the trends of tool front and flank wear, cutting force and surface roughness with machining length (L). The results show that compared with CC, the flank wear (VB) under UEVC and TUEVC is reduced by 57.06% and 69.42% on average, and the length of cutting edge wear (lc) and the width of cutting edge retraction (dR) are reduced by 21.94%, 23.62%, and 34.78%, 60.58%, respectively; compared with UEVC, the VB under TUEVC is reduced by 7.24% but lc and lR are relatively increased by 2.28% and 36.14%. Compared with CC, the tangential, backward, and axial forces under UEVC and TUEVC were significantly reduced; compared with UEVC, the backward and tangential forces under TUEVC were reduced by 0.6 N and 0.19 N on average, and the axial force increased by 0.51 N on average.The surface roughness under TUEVC was reduced by a maximum of 33.8% compared with that of UEVC, and the average reduction was 13.9%.
- 19 August 2025
- Published by Springer Nature in Research Square
Open AccessResearch on cutting forces and tool wear during tilted ultrasonic elliptical vibration cutting of Ti-6Al-4V
Titanium alloy has the characteristics of high strength, low thermal conductivity, high ductility, etc. When machining it by conventional process, there are problems such as high local temperature in the machining area, serious tool wear and low machining quality. In this paper, the cutting force and tool wear of TC4 titanium alloy under tilted ultrasonic elliptical vibration cutting (TUEVC) was studied by using a Suzhou Sunshines Ultrasonic Equipment. Firstly, the material removal mechanisms under the three machining modes of conventional cutting (CC), conventional ultrasonic elliptical vibration cutting (UEVC) and TUEVC were compared and analysed, as well as the influence of the tilt angle on the cutting force under ultrasonic elliptical vibration cutting. Subsequently, tool wear experiments were carried out for the three machining modes to compare the trends of tool front and flank wear, cutting force and surface roughness with machining length (L). The results show that compared with CC, the flank wear (VB) under UEVC and TUEVC is reduced by 57.06% and 69.42% on average, and the length of cutting edge wear (lc) and the width of cutting edge retraction (dR) are reduced by 21.94%, 23.62%, and 34.78%, 60.58%, respectively; compared with UEVC, the VB under TUEVC is reduced by 7.24% but lc and lR are relatively increased by 2.28% and 36.14%. Compared with CC, the tangential, backward, and axial forces under UEVC and TUEVC were significantly reduced; compared with UEVC, the backward and tangential forces under TUEVC were reduced by 0.6 N and 0.19 N on average, and the axial force increased by 0.51 N on average.The surface roughness under TUEVC was reduced by a maximum of 33.8% compared with that of UEVC, and the average reduction was 13.9%.
- Open Access
- 9 May 2025
- Published by Springer Nature in Research Square
Research on burr height prediction and inhibition strategy of high-temperature alloy ultrasonic vibration micro drilling outlet
GH4169 is a nickel-based super-alloy characterized by outstanding resistance to high temperatures, corrosion, and fatigue. Owing to these properties, it is extensively used in the aerospace industry for manufacturing hot-section components, particularly turbine blades in aero-engines. Air film holes are critical structural features on aircraft engine turbine blades, burr formation is a common occurrence in the drilling process. This article analyzes the process of burr formation in conventional drilling(CD) and ultrasonic assistant vibration drilling(UAD), develops an analytical model for predicting burr height evolution in UAD based on the principle of energy conservation. The framework integrates dynamic cutting mechanics with plastic deformation energy dissipation, establishing quantitative correlations between processing parameters and burr height. Experimental results demonstrate that, running at 9000 rpm spindle rotation speed, while maintaining a 5 mm/min feeding motion, UAD with a 6µm amplitude reduces the axial force from 13.29 N in CD to 7.34 N, representing a 44.75% decrease. Additionally, the burr height decreases from 36.13µm to 28µm, representing a 22.5% reduction. The burr morphology also changes, forming a ring of thin, curved burrs at the hole exit. To quantify the impact of machining conditions on burr dimensions, multivariate regression analysis(MRA) was systematically implemented in the study, while also calculating the material removal rate (MRR). Through optimization, the study identified a set of ultrasonic micro-drilling parameters. The parameter configuration, ultrasonic amplitude: 6µm; feed rate: 6.3 mm/min; spindle speed: 9000 r/min, achieves optimal burr suppression, while sustaining a high material removal rate.
- 9 May 2025
- Published by Springer Nature in Research Square
Open AccessResearch on burr height prediction and inhibition strategy of high-temperature alloy ultrasonic vibration micro drilling outlet
GH4169 is a nickel-based super-alloy characterized by outstanding resistance to high temperatures, corrosion, and fatigue. Owing to these properties, it is extensively used in the aerospace industry for manufacturing hot-section components, particularly turbine blades in aero-engines. Air film holes are critical structural features on aircraft engine turbine blades, burr formation is a common occurrence in the drilling process. This article analyzes the process of burr formation in conventional drilling(CD) and ultrasonic assistant vibration drilling(UAD), develops an analytical model for predicting burr height evolution in UAD based on the principle of energy conservation. The framework integrates dynamic cutting mechanics with plastic deformation energy dissipation, establishing quantitative correlations between processing parameters and burr height. Experimental results demonstrate that, running at 9000 rpm spindle rotation speed, while maintaining a 5 mm/min feeding motion, UAD with a 6µm amplitude reduces the axial force from 13.29 N in CD to 7.34 N, representing a 44.75% decrease. Additionally, the burr height decreases from 36.13µm to 28µm, representing a 22.5% reduction. The burr morphology also changes, forming a ring of thin, curved burrs at the hole exit. To quantify the impact of machining conditions on burr dimensions, multivariate regression analysis(MRA) was systematically implemented in the study, while also calculating the material removal rate (MRR). Through optimization, the study identified a set of ultrasonic micro-drilling parameters. The parameter configuration, ultrasonic amplitude: 6µm; feed rate: 6.3 mm/min; spindle speed: 9000 r/min, achieves optimal burr suppression, while sustaining a high material removal rate.
- 1 January 2024
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 60 (9) , 57-74
Research on Wheel Wear and Grinding Performance of Elliptical Ultrasonic Vibration Assisted Grinding SiC Ceramics
- 1 January 2024
- Published by Chinese Journal of Mechanical Engineering in Journal of Mechanical Engineering
- Vol. 60 (9) , 57-74
Research on Wheel Wear and Grinding Performance of Elliptical Ultrasonic Vibration Assisted Grinding SiC Ceramics
- 14 June 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 127 (7-8) , 3413-3425
Experimental research and multi-objective optimization of ultrasonic vibration–assisted EDM for Ti6Al4V micro-holes
- 14 June 2023
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 127 (7-8) , 3413-3425
Experimental research and multi-objective optimization of ultrasonic vibration–assisted EDM for Ti6Al4V micro-holes
- Open Access
An Experimental Study of the Surface Roughness of SiCp/Al with Ultrasonic Vibration-Assisted Grinding
Due to the differences in mechanical properties of Al and SiC particles, the problems of SiC particle pullout and high surface roughness will occur in the processing of SiCp/Al composites. However, the ultrasonic vibration-assisted grinding of SiCp/Al can effectively decrease the appearance of such problems. A comparative experimental study of the ultrasonic vibration-assisted and ordinary grinding of SiCp/Al is conducted. First, the effect of ultrasonic amplitude on the removal form of SiC is summarized by observing the surface morphology of the sample. Then, the primary reasons for the pullout of SiC particles and high surface roughness in SiCp/Al processing are analyzed. The variation law of the surface roughness of SiCp/Al under different ultrasonic amplitudes and grinding parameters is summarized through a single-factor experiment. The results show that ultrasonic vibration-assisted grinding is beneficial for reducing the surface roughness of SiCp/Al. When grinding linear speed of grinding wheel vs increases from 2.512 m/s to 7.536 m/s, surface roughness Ra decreases from 0.25 µm to 0.16 µm. when feed rate vw increases from 100 mm/min to 1700 mm/min, surface roughness Ra increases from 0.13 µm to 0.20 µm. When grinding depth ap increases from 0.01 mm to 0.05 mm, surface roughness Ra increases from 0.13 µm to 0.19 µm. When ultrasonic amplitude A is increased from 0 µm to 2 µm, surface roughness Ra decreases from 0.26 µm to 0.15 µm. When ultrasonic amplitude A is increased from 2 µm to 4.4 µm, surface roughness Ra increases from 0.15 µm to 0.18 µm.
Open AccessAn Experimental Study of the Surface Roughness of SiCp/Al with Ultrasonic Vibration-Assisted Grinding
Due to the differences in mechanical properties of Al and SiC particles, the problems of SiC particle pullout and high surface roughness will occur in the processing of SiCp/Al composites. However, the ultrasonic vibration-assisted grinding of SiCp/Al can effectively decrease the appearance of such problems. A comparative experimental study of the ultrasonic vibration-assisted and ordinary grinding of SiCp/Al is conducted. First, the effect of ultrasonic amplitude on the removal form of SiC is summarized by observing the surface morphology of the sample. Then, the primary reasons for the pullout of SiC particles and high surface roughness in SiCp/Al processing are analyzed. The variation law of the surface roughness of SiCp/Al under different ultrasonic amplitudes and grinding parameters is summarized through a single-factor experiment. The results show that ultrasonic vibration-assisted grinding is beneficial for reducing the surface roughness of SiCp/Al. When grinding linear speed of grinding wheel vs increases from 2.512 m/s to 7.536 m/s, surface roughness Ra decreases from 0.25 µm to 0.16 µm. when feed rate vw increases from 100 mm/min to 1700 mm/min, surface roughness Ra increases from 0.13 µm to 0.20 µm. When grinding depth ap increases from 0.01 mm to 0.05 mm, surface roughness Ra increases from 0.13 µm to 0.19 µm. When ultrasonic amplitude A is increased from 0 µm to 2 µm, surface roughness Ra decreases from 0.26 µm to 0.15 µm. When ultrasonic amplitude A is increased from 2 µm to 4.4 µm, surface roughness Ra increases from 0.15 µm to 0.18 µm.
- 23 August 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 122 (3-4) , 1513-1524
The effect of ultrasonic amplitude on the performance of ultrasonic vibration-assisted EDM micro-hole machining
- 23 August 2022
- Published by Springer Nature in The International Journal of Advanced Manufacturing Technology
- Vol. 122 (3-4) , 1513-1524
The effect of ultrasonic amplitude on the performance of ultrasonic vibration-assisted EDM micro-hole machining