WWWenbo Wang

Wenbo Wang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Wenbo Wang has a total of 37 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Improved Planar Transformers With Common-Mode Noise Cancellation for LLC Converters

    by Junyun Deng, Wenbo Wang, Prasanth Venugopal, Jelena Popovic, Gert Rietveld

    Planar transformers have significant advantages due to their strong parasitic parameter control ability and low profile in high-frequency power electronic applications. However, they also suffer from serious common-mode (CM) noise issues due to their large planar surface areas. To overcome this drawback, a novel method is proposed to reduce CM noise current by fine-tuning layer-to-layer CM capacitances in the planar transformer. To demonstrate the applicability of our method, a CM current model is established for LLC converters with different circuit configurations based on an analysis of the transformer layer-to-layer CM currents. The proposed concept has the advantage that it enables interleaving winding arrangements without the need for extra shielding layers. This article focuses on planar transformers without magnetic integration, which combines magnetic components into a single core. For integrated magnetics, the CM noise cancellation method is proposed to address this issue in our previous conference work. Experimental comparisons between planar transformers with CM capacitance regulation and their conventional counterparts prove the applicability and effectiveness of our proposed method. The results show the CM noises for two LLC converters are reduced by about 19% and 9.0% respectively by employing the proposed method. Our proposed method is well-suited for high-frequency applications where core saturation is not a concern, and where one turn of winding per layer is preferred to reduce winding loss.

  • Anomalous dynamic on-resistance instability mechanisms of p-GaN gate AlGaN/GaN HEMTs under power cycling tests

    by Chengbing Pan, Ruomeng Zhang, Xueyan Li, Yibo Ning, Wenbo Wang, Lixia Zhao

    In this study, the instability mechanisms of dynamic on-resistance (RDSON) of p-GaN gate AlGaN/GaN high electron mobility transistors (HEMTs) were investigated under power cycling tests (PCTs). An anomalous dynamic RDSON instability behavior was observed, with an obvious decrease of 17.8% in the first stage (≤30k-cycle PCT), followed by a slight increase of 8.6%. The deep-level transient spectroscopy results show that the electron trap concentration in the AlGaN/GaN region and the hole trap concentration in the p-GaN layer decreased in the first stage, and then increased with increasing stress time. In addition, a new hole trap appeared in the AlGaN/GaN region after the 30k-cycle PCT. The decreased concentrations of the electron trap and hole trap below the gate increase the electrons in the two-dimensional electron gas in the first stage, reducing the dynamic RDSON. Afterward, the electron trapping enhances the depletion of the channel electrons and the increased hole trap concentration causes net negative charges under the gate, increasing the dynamic RDSON. This work provides important experimental evidence to understand the underlying mechanisms of the dynamic RDSON instability in p-GaN gate AlGaN/GaN HEMTs.


  • Package-Level Electro-Thermal Simulation With Transient Thermal Resistance Model for Surge Stress Failure Analysis of SiC MOSFET

    by Zaiman Xiang, Tao Luo, Wenbo Wang, Bo Sun, Botao Sun, Qingchun Zhang, Guoqi Zhang, Jiajie Fan

    This paper investigates the surge reliability of commercial 1200V SiC MOSFETs through a combined approach of experimental testing and multiphysics simulation, elucidating the failure mechanisms under both step and repetitive surge current stress. The innovative integration of package-level electro-thermal coupling simulation with transient junction temperature estimation overcomes the limitations of conventional methodologies that rely solely on decapsulation analysis and TCAD simulation. Experimental evaluations on six DUTs with distinct structural configurations, employing surge testing and failure analysis techniques including C-SAM, optical microscopy, and SEM, confirm that device failure primarily originates from gate-source short circuits caused by aluminum bonding wire melting. COMSOL multiphysics simulations further replicate the transient thermal characteristics of bonding wire regions, demonstrating rapid temperature escalation to the Aluminum melting point within 5-6 ms during surge events. A transient thermal resistance-based junction temperature characterization method is proposed, revealing an inverse proportionality between thermal resistance and chip area.


  • Warpage Optimization for SiC MOSFET Multichip Fan-Out Panel-Level Packaging With Thermal–Mechanical Finite-Difference Numerical Modeling and In Situ Digital Image Correlation Validation

    by Wenyu Li, Wei Chen, Jing Jiang, Wenbo Wang, Yuhan Gao, Fulong Zhu, Xuejun Fan, Guoqi Zhang, Jiajie Fan

    Fan-out panel-level package has become a trend in silicon carbide mosfet packaging due to its superior electrothermal performance and cost-effectiveness. However, the increased size of multichip embedded fan-out panel-level packaging (FOPLP) introduces greater challenges in sample preparation and thermal–mechanical stresses. In this article, a large-sized (20 mm*20 mm*0.78 mm) FOPLP with four SiC mosfets embedded is investigated. A 3-D thermal–mechanical numerical model is derived based on heat conduction and elasticity theories. It utilized analytical solutions of Fourier temperature conduction and finite-difference results for thermoelastic models to describe the temperature and deformation distribution during the FOPLP operation. It also reveals the heat-coupling issue of multiple chips. Compared with the finite-element simulation, the proposed method shows less than 2.5% error in temperature and 2.3% error in deformation. The computational speed is one-tenth that of the finite-element method, while the memory usage is reduced to one-fifth. To mitigate the influence of chip thermal coupling on temperature and warpage, an optimized layout was employed to achieve temperature uniformity improvement. Finally, FOPLPs with the two layouts were fabricated. The warpage was monitored using a digital image correlation platform. To achieve the same temperature, the current required for the optimized layout was increased by 9% . The warpage of the optimized layout at 60 °C was reduced by 13.5%, and at 100 °C, it was reduced by 14.7%, validating the accuracy of the model and the significance of thermal decoupling.


  • Degradation Mechanisms of p-GaN Gate AlGaN/GaN High-Electron-Mobility Transistors Under High-Temperature Reverse Bias Stress

    by Chengbing Pan, Wenbo Wang, Ruomeng Zhang, Xinyuan Zheng, Xueyan Li, Yesen Han, Yibo Ning, Haodong Zhang, Lixia Zhao

    The p-GaN gate AlGaN/GaN high-electron-mobility transistors (HEMTs) are promising for many applications, including electric vehicles, radar, etc. However, the threshold voltage (VTH) instability and dynamic ON-resistance (RDSON) degradation of p-GaN gate AlGaN/GaN HEMTs remain a concern. Here, the degradation behaviors of threshold voltage and dynamic RDSON of p-GaN gate AlGaN/GaN HEMTs were systematically investigated. An anomalous shift of threshold voltage was observed with a slight negative shift in the first stage (DSON after 432 h stress increased by approximately 54.5%. The thermal resistance increased by 0.78 K/W for the chip and 0.38 K/W for the die attach. The defects evolution in the epilayers during the stress was measured using deep-level transient spectroscopy. The results show that the electron trap concentration decreased, and a new hole trap level appeared in the AlGaN/GaN region after the degradation. In the first stage (TH shift. Afterward, hole emission leads to the net negative charges beneath the gate, causing the positive VTH shift and the increase of dynamic RDSON. These results can help to further improve the reliability of p-GaN gate AlGaN/GaN HEMTs.


  • A Double-Sided Cooling SiC Power Module With Pressure Contact Packaging

    by Lei Wang, Wenbo Wang, Keqiu Zeng, Ruomeng Zhang, Gert Rietveld, Raymond J. E. Hueting

    Pressure contact technology (PCT) in power modules offers advantages in improved thermo-mechanical performance and double-sided cooling. This work presents the design and implementation of a proposed PCT in a half-bridge SiC active metal brazed (AMB)-based module. The 3D layout of the power loop provides external degrees of freedom to minimize the commutation loop inductance and to balance the current. To accommodate the small footprint of SiC MOSFETs, graphene films (GFs) and fuzz buttons are applied for the source/drain connectors and gate pins, respectively. These soft connectors not only conduct current and heat but also absorb a certain amount of thermal stress. A thermo-mechanical coupled model under fluid cooling condition is developed to precisely compare the performance of the modules fabricated both with Molybdenum (Mo) and GF connectors. The implementation of GFs significantly reduces the junction temperature and balances the stress of the chips. The double-sided cooling reduces the measured junction to heatsink thermal resistance of the experimental prototype with GF to 0.68 K/W. The double pulse test of the prototype demonstrates a low parasitic inductance of 5.1 nH and a voltage overshoot of only 5.8 %.


  • High-Frequency Core Loss Modeling Based on Knowledge-Aware Artificial Neural Network

    by Junyun Deng, Wenbo Wang, Zhansheng Ning, Prasanth Venugopal, Jelena Popovic, Gert Rietveld

    High-frequency core loss modeling plays a critical role in the magnetics design of power electronics. However, existing modeling tools fail to achieve both high speed and high precision. The conventional analytical approach enables fast estimations but performs poorly in accuracy. Magnetic loss models aided by loss maps feature high accuracy, but their model parameterization relies on large data. The emerging approach of artificial neural networks (ANNs) provides a promising alternative since it can achieve high speed and accuracy. However, conventional implementations of ANN require a large and accurate dataset for training, which is hard to achieve in magnetic loss modeling. To solve this problem, a knowledge-aware artificial neural network (KANN) is proposed that can achieve high accuracy with small training datasets. After introducing the principle of the proposed KANN, it is applied to high-frequency core loss modeling using the improved generalized Steinmetz equation as additional knowledge. To validate the performance of the proposed KANN-based design method for core loss modeling, it is applied to predict the losses of two ferrite cores in the frequency range of 50–450 kHz. The results show that the proposed method greatly outperforms present loss modeling approaches in accuracy and speed, requiring only a limited training dataset. An automatic loss modeling tool based on the new method is provided together with its open-source code.


  • Opportunities and Challenges of Pressure Contact Packaging for Wide Bandgap Power Modules

    by Lei Wang, Wenbo Wang, Keqiu Zeng, Junyun Deng, Gert Rietveld, Raymond J. E. Hueting

    Conventional packaging technologies cannot facilitate full utilization of wide bandgap (WBG) power modules due to the parasitics of wire bonds and the thermal stresses in solder layers. Pressure contact technology is considered to be an effective approach to reduce stress and to make the assembly compact by replacing solder materials and wire bonds. This article reviews the state of the art of pressure contact packaging and discusses the advantages and limitations of various adopted methodologies. The challenges are revealed in detail in terms of die metallization, multiphysical design, stress distribution, and failures in pressure-based joints. In addition, potential future trends of pressure contact packaging toward different power levels and strategies to select appropriate technologies for different scenarios are discussed. This work aims to support designers in implementing pressure contacts in WBG power modules to fully exploit their advantages and to improve the reliability in thermal cycling.


  • Review of Topside Interconnections for Wide Bandgap Power Semiconductor Packaging

    by Lisheng Wang, Wenbo Wang, Raymond J. E. Hueting, Gert Rietveld, Jan Abraham Ferreira

    Due to their superior material properties, wide bandgap (WBG) semiconductors enable the application of power electronics at higher temperature operation, higher frequencies, and higher efficiencies compared to silicon (Si). However, the commonly-used aluminum wire bonding as topside interconnection technology prevents WBG semiconductors from reaching their full potential, due to inherent parasitic inductances, large size, heat dissipation, and reliability issues of wire bonding technology. Therefore, this article presents a comprehensive review of topside interconnection technologies of WBG semiconductor power devices and modules. First, the challenges and driving factors for the interconnection of WBG semiconductor dies are discussed. Second, for each widely commercially used WBG semiconductor, i.e., silicon carbide and gallium nitride, technical details and innovative features of state-of-the-art interconnection techniques in packages are reviewed. Then, the majority of existing topside interconnection materials for WBG semiconductors are categorized and compared, followed by a discussion of their advantages, challenges, and failure modes. Based on this elaborate discussion, potential future directions of the interconnection technology development are given. It is concluded that the superior performance of WBG semiconductors can be obtained by combining novel materials with innovative designs for the topside interconnections.