Jianxun Dai
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Jianxun Dai has a total of 102 co-authors. Here are the top co-authors by number of shared publications:
- Huolin Huang
Central Hospital of Dalian University of Technology, Dalian, P.R. China
15 shared publications - Yung. C. Liang
Department of Electrical and Computer Engineering, National University of Singapore, Singapore
5 shared publications - Nan Sun
School of Optoelectronic Engineering and Instrumentation Science, Dalian University of Technology, Dalian, China
4 shared publications - Rong Han
School of Optoelectronic Engineering and Instrumentation Science, Dalian University of Technology 1 , Dalian 116024
4 shared publications - Xin Xia
Dalian University of Technology
4 shared publications Yun Lei
School of Optoelectronic Engineering and Instrumentation Science, Dalian University of Technology, Dalian, China
4 shared publications
Latest Publications
- 13 October 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (29) , 2201
Evolution of resistive switching behavior regulated by GaOxN1−x interfacial engineering
- 13 October 2026
- Published by Springer Nature in Journal of Materials Science: Materials in Electronics
- Vol. 37 (29) , 2201
Evolution of resistive switching behavior regulated by GaOxN1−x interfacial engineering
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (10) , 5936-5943
1700-V Enhancement-Mode MIS-HEMTs With Fully Recessed-Gate on 6-in GaN-on-Si Wafer
- 1 October 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 73 (10) , 5936-5943
1700-V Enhancement-Mode MIS-HEMTs With Fully Recessed-Gate on 6-in GaN-on-Si Wafer
- 21 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (12)
High-voltage normally off GaN-based MIS-HEMTs featuring rounded gate sidewalls
This work proposes a normally off gallium nitride (GaN)-based high electron mobility transistor (HEMT) that features rounded gate sidewalls and smooth corner profiles. To facilitate superior gate dielectric growth and coverage, we employed a hybrid-recess scheme combining a two-step etching process with an N2/O2 plasma treatment, resulting in significant etch-induced damage mitigation and interface trap density reduction. Compared to the traditional devices without plasma treatment, our devices exhibited not only a remarkable 156% rise in saturation current density but also a dramatic 108% increase in transconductance, alongside the nearly eliminated threshold-voltage hysteresis. More importantly, attributed to the suppression of the peak electric field under high-voltage stress by the rounded corners, the gate breakdown voltage and off-state breakdown voltage are enhanced to 26 and 1447 V, respectively, consistent with the technology computer-aided design simulation analysis. Finally, double-pulse measurements were conducted to further confirm the reduced interface trap density and improved reliability of the hybrid-recess device. In summary, we demonstrate a normally off GaN-based HEMT with rounded etched sidewalls as a key feature, thereby establishing a promising strategy for high-voltage power devices.
- 21 September 2026
- Published by AIP Publishing in Applied Physics Letters
- Vol. 129 (12)
High-voltage normally off GaN-based MIS-HEMTs featuring rounded gate sidewalls
This work proposes a normally off gallium nitride (GaN)-based high electron mobility transistor (HEMT) that features rounded gate sidewalls and smooth corner profiles. To facilitate superior gate dielectric growth and coverage, we employed a hybrid-recess scheme combining a two-step etching process with an N2/O2 plasma treatment, resulting in significant etch-induced damage mitigation and interface trap density reduction. Compared to the traditional devices without plasma treatment, our devices exhibited not only a remarkable 156% rise in saturation current density but also a dramatic 108% increase in transconductance, alongside the nearly eliminated threshold-voltage hysteresis. More importantly, attributed to the suppression of the peak electric field under high-voltage stress by the rounded corners, the gate breakdown voltage and off-state breakdown voltage are enhanced to 26 and 1447 V, respectively, consistent with the technology computer-aided design simulation analysis. Finally, double-pulse measurements were conducted to further confirm the reduced interface trap density and improved reliability of the hybrid-recess device. In summary, we demonstrate a normally off GaN-based HEMT with rounded etched sidewalls as a key feature, thereby establishing a promising strategy for high-voltage power devices.
- 5 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Recessed-Gate Enhancement-Mode GaN HEMTs: Pre-Stress-Free High-Voltage Pulse Testing and Its Effects on Dynamic On-Resistance
Conventional dynamic on-resistance (RON) measurement for the high-voltage (HV) power devices typically employs pre-HV stress prior to the pulse testing which deviates from the actual application conditions. To address this issue, a pre-stress-free pulsed testing method is adopted to explore the HV dynamic RON characteristics of self-developed recessed-gate enhancement-mode gallium nitride (GaN) high-electron-mobility transistors (HEMTs), which feature a threshold voltage of approximately 2 V and a current on-off ratio exceeding 10⁹. A pulse-testing method that enables precise control of pulse width and frequency is proposed herein. Test results demonstrate that the normalized dynamic RON obtained via the pre-stress-free pulsed testing is significantly smaller (25% found under the pre-stress-free testing versus 55% under conventional testing condition), revealing the critical necessity of eliminating pre-stress for HV pulse testing. This study also delves into the influence of key operating parameters, including gate voltage, switching frequency, and temperature, on dynamic RON. By eliminating pre-HV stress, this testing technique enables more accurate evaluation of the dynamic performance of GaN HEMTs in HV applications. These findings advance the understanding of dynamic behavior of recessed-gate enhancement-mode GaN HEMTs and provide crucial guidance for optimizing device design and operation to minimize dynamic RON, thereby enhancing performance for power electronics applications.
- 5 June 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Emerging and Selected Topics in Power Electronics
- Vol. PP (21686777) , 1
Recessed-Gate Enhancement-Mode GaN HEMTs: Pre-Stress-Free High-Voltage Pulse Testing and Its Effects on Dynamic On-Resistance
Conventional dynamic on-resistance (RON) measurement for the high-voltage (HV) power devices typically employs pre-HV stress prior to the pulse testing which deviates from the actual application conditions. To address this issue, a pre-stress-free pulsed testing method is adopted to explore the HV dynamic RON characteristics of self-developed recessed-gate enhancement-mode gallium nitride (GaN) high-electron-mobility transistors (HEMTs), which feature a threshold voltage of approximately 2 V and a current on-off ratio exceeding 10⁹. A pulse-testing method that enables precise control of pulse width and frequency is proposed herein. Test results demonstrate that the normalized dynamic RON obtained via the pre-stress-free pulsed testing is significantly smaller (25% found under the pre-stress-free testing versus 55% under conventional testing condition), revealing the critical necessity of eliminating pre-stress for HV pulse testing. This study also delves into the influence of key operating parameters, including gate voltage, switching frequency, and temperature, on dynamic RON. By eliminating pre-HV stress, this testing technique enables more accurate evaluation of the dynamic performance of GaN HEMTs in HV applications. These findings advance the understanding of dynamic behavior of recessed-gate enhancement-mode GaN HEMTs and provide crucial guidance for optimizing device design and operation to minimize dynamic RON, thereby enhancing performance for power electronics applications.
- Open Access
- 12 May 2026
- Published by Elsevier in SSRN Electronic Journal
Ionogel based Multifunctional Sensors for Physiological Signal Detection and Mechanism Analysis
This study presents a class of polymer ionogels (PIGs) synthesized via a facile click chemistry approach, which integrates pressure sensing, humidity sensing, and self-powered functionalities into a single flexible platform. The PIG exhibits exceptional performance: (1) A high-pressure sensitivity of 7.98 kPa-1 at 238 Pa with rapid response/recovery times (<500 ms); (2) A wide humidity detection range (11-97% RH) and high sensitivity (Z11% RH/Z97% RH=1.5×104); (3) A self-generated voltage of ~100 mV under 97% RH driven by humidity-induced ion migration, eliminating external power requirements. The sensing mechanisms are elucidated through complex impedance spectroscopy and ion dynamics analysis, revealing that Br- ion redistribution, under humidity gradients and compressive deformation-induced capacitive changes synergistically enable multimodal signal detection. Demonstrations in real-time monitoring of swallowing, respiration, and arterial pulses highlight its potential in wearable healthcare and human-machine interfaces. This work provides a material-level innovation for designing self-sustained multifunctional sensors, addressing critical challenges in energy autonomy and integration complexity for next-generation electronic skin systems.
- 12 May 2026
- Published by Elsevier in SSRN Electronic Journal
Open AccessIonogel based Multifunctional Sensors for Physiological Signal Detection and Mechanism Analysis
This study presents a class of polymer ionogels (PIGs) synthesized via a facile click chemistry approach, which integrates pressure sensing, humidity sensing, and self-powered functionalities into a single flexible platform. The PIG exhibits exceptional performance: (1) A high-pressure sensitivity of 7.98 kPa-1 at 238 Pa with rapid response/recovery times (<500 ms); (2) A wide humidity detection range (11-97% RH) and high sensitivity (Z11% RH/Z97% RH=1.5×104); (3) A self-generated voltage of ~100 mV under 97% RH driven by humidity-induced ion migration, eliminating external power requirements. The sensing mechanisms are elucidated through complex impedance spectroscopy and ion dynamics analysis, revealing that Br- ion redistribution, under humidity gradients and compressive deformation-induced capacitive changes synergistically enable multimodal signal detection. Demonstrations in real-time monitoring of swallowing, respiration, and arterial pulses highlight its potential in wearable healthcare and human-machine interfaces. This work provides a material-level innovation for designing self-sustained multifunctional sensors, addressing critical challenges in energy autonomy and integration complexity for next-generation electronic skin systems.
- 24 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-9
A Portable Gauss Meter With Low Offset Based on AlGaN/GaN Hall Sensor Probe Suitable for High-Temperature Environment
By employing compact and portable magnetic sensing probes, Gauss meters enable precise magnetic field measurements in confined spaces or on material surfaces. In this work, a low offset portable Gauss meter with adjustable gain, which is used for measuring linear magnetic field in extreme environment such as high temperature, is made using GaN-based Hall sensor as the sensitive probe. Firstly, four different sizes of cross-shaped Hall sensors with quadruple rotationally symmetrical structures were designed and fabricated on AlGaN/GaN epitaxial wafer, and the output characteristics of the devices were measured and discussed in detail. At room temperature, devices with a larger aspect ratio have a higher current-related sensitivity of 68.2 V/AꞏT, while devices with a smaller aspect ratio have a higher voltage-related sensitivity of 0.0268 /T. The GaN-based Hall sensors can work stably in the temperature range of room temperature to 400 °C, with a minimum temperature drift coefficient of 374.8 ppm/K for current-related sensitivity. In addition, a dual half-bridge structure offset elimination circuit tailored for GaN-based Hall sensors was proposed based on the spinning current method. Finally, the performance of the Gauss meter microsystem was evaluated. Experimental results show that at 1 mA bias current, the Gauss meter microsystem achieves the maximum magnetic field measurement range from -1.0 T to 1.0 T where the gain of the microsystem is 27, boasts the maximum sensitivity of 15.09 mV/mT with the nonlinear error of less than 0.05 % where the gain is 241, and offers the resolution as low as 26 μT.
- 24 October 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 74 (00189456) , 1-9
A Portable Gauss Meter With Low Offset Based on AlGaN/GaN Hall Sensor Probe Suitable for High-Temperature Environment
By employing compact and portable magnetic sensing probes, Gauss meters enable precise magnetic field measurements in confined spaces or on material surfaces. In this work, a low offset portable Gauss meter with adjustable gain, which is used for measuring linear magnetic field in extreme environment such as high temperature, is made using GaN-based Hall sensor as the sensitive probe. Firstly, four different sizes of cross-shaped Hall sensors with quadruple rotationally symmetrical structures were designed and fabricated on AlGaN/GaN epitaxial wafer, and the output characteristics of the devices were measured and discussed in detail. At room temperature, devices with a larger aspect ratio have a higher current-related sensitivity of 68.2 V/AꞏT, while devices with a smaller aspect ratio have a higher voltage-related sensitivity of 0.0268 /T. The GaN-based Hall sensors can work stably in the temperature range of room temperature to 400 °C, with a minimum temperature drift coefficient of 374.8 ppm/K for current-related sensitivity. In addition, a dual half-bridge structure offset elimination circuit tailored for GaN-based Hall sensors was proposed based on the spinning current method. Finally, the performance of the Gauss meter microsystem was evaluated. Experimental results show that at 1 mA bias current, the Gauss meter microsystem achieves the maximum magnetic field measurement range from -1.0 T to 1.0 T where the gain of the microsystem is 27, boasts the maximum sensitivity of 15.09 mV/mT with the nonlinear error of less than 0.05 % where the gain is 241, and offers the resolution as low as 26 μT.
- 3 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (6) , 9384-9392
A Room-Temperature Dual-Gas Humidity/Ammonia Sensor Based on Gallium Oxide for Breath Analysis
The analysis of human breath to detect both respiration state and breath biomarkers is of great importance in the fields of exhaled noninvasive breath monitoring and diagnosis. Thus, we have elaborately synthesized gallium oxide (Ga2O3) with different oxygen species as humidity and gas sensitive materials to monitor respiratory function and ammonia (NH3). In this work, the sensing characteristics and breath monitoring applications of the humidity/ammonia sensor based on the Ga2O3 are systematically investigated. The humidity sensor demonstrated high responsivity (over 3 orders of magnitude), low humidity hysteresis (1.83%) and good long-term stability. The ammonia sensor has a response of 1.2% to 2 ppm ammonia at 70% RH. To investigate the potential application of the sensor in detecting ammonia in exhaled gas, a simulated breath test was conducted.
- 3 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Sensors Journal
- Vol. 25 (6) , 9384-9392
A Room-Temperature Dual-Gas Humidity/Ammonia Sensor Based on Gallium Oxide for Breath Analysis
The analysis of human breath to detect both respiration state and breath biomarkers is of great importance in the fields of exhaled noninvasive breath monitoring and diagnosis. Thus, we have elaborately synthesized gallium oxide (Ga2O3) with different oxygen species as humidity and gas sensitive materials to monitor respiratory function and ammonia (NH3). In this work, the sensing characteristics and breath monitoring applications of the humidity/ammonia sensor based on the Ga2O3 are systematically investigated. The humidity sensor demonstrated high responsivity (over 3 orders of magnitude), low humidity hysteresis (1.83%) and good long-term stability. The ammonia sensor has a response of 1.2% to 2 ppm ammonia at 70% RH. To investigate the potential application of the sensor in detecting ammonia in exhaled gas, a simulated breath test was conducted.
- 7 November 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (4) , 045106
Improved breakdown voltage and dynamic Ron characteristics in normally-off GaN-based HEMTs featuring fully-recessed and bilayer-dielectric gate structure
The degradation of dynamic on-resistance (R on) is a major challenge in GaN-based high electron mobility transistors, which seriously affects their performance and reliability. The degradation area of dynamic R on mainly comes from two aspects. One is the region below the gate that also affects the threshold voltage (V th) of the devices. The other one is the interface region of the gate to drain access. The optimal device exhibits a V th of 0.97 V, a small V th hysteresis of only 20 mV, a high current density of 723 mA mm−1, and a breakdown voltage of 810 V which can be further boosted when additional field plate design is employed. It is found that when high voltage drain stress is applied, a positive V th shift is induced, leading to a decrease in the effective gate driving voltage, and thus the dynamic R on of the devices is increased. Of particular concern are the effects of dielectric layer and/or interface of the access region on the dynamic R on degradation, which can be alleviated by removing the dielectric layer from the access region.
- 7 November 2024
- Published by IOP Publishing in Journal of Physics D: Applied Physics
- Vol. 58 (4) , 045106
Improved breakdown voltage and dynamic Ron characteristics in normally-off GaN-based HEMTs featuring fully-recessed and bilayer-dielectric gate structure
The degradation of dynamic on-resistance (R on) is a major challenge in GaN-based high electron mobility transistors, which seriously affects their performance and reliability. The degradation area of dynamic R on mainly comes from two aspects. One is the region below the gate that also affects the threshold voltage (V th) of the devices. The other one is the interface region of the gate to drain access. The optimal device exhibits a V th of 0.97 V, a small V th hysteresis of only 20 mV, a high current density of 723 mA mm−1, and a breakdown voltage of 810 V which can be further boosted when additional field plate design is employed. It is found that when high voltage drain stress is applied, a positive V th shift is induced, leading to a decrease in the effective gate driving voltage, and thus the dynamic R on of the devices is increased. Of particular concern are the effects of dielectric layer and/or interface of the access region on the dynamic R on degradation, which can be alleviated by removing the dielectric layer from the access region.
- 9 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 6934-6941
Low Turn-On Voltage and Reverse Leakage Current β -Ga2O3 MIS Schottky Barrier Diodes With an AlN Interfacial Layer
We demonstrate for the first time a vertical metal/AlN/$\beta $ -gallium oxide ($\beta $ -Ga2O3) metal-insulator–semiconductor (MIS) Schottky barrier diode (SBD) with low turn-on voltage (${V}_{\text {on}}$ ) and reverse leakage current. By employing an ultrathin AlN layer enabled by atomic layer deposition (ALD), the resulting AlN/$\beta $ -Ga2O3 MIS SBD exhibits a remarkably low leakage current of$0.1~\mu $ A/cm2, which is three orders of magnitude smaller than that of the conventional$\beta $ -Ga2O3 SBD. Meanwhile, the AlN/$\beta $ -Ga2O3 MIS SBD shows a significantly improved breakdown voltage from 208 V up to 890 V, while maintaining a relatively low${V}_{\text {on}}$ of 0.92 V and on-resistance (${R}_{\text {on}}$ ) of 11.8 m$\Omega \cdot $ cm2, respectively. I–V measurements conducted across a range of temperatures from 298 to 432 K indicate that thermionic field emission (TFE) and trap-assisted tunneling (TAT) are the predominant electron transport mechanisms under forward bias if inserting 2 nm AlN, while TFE becomes dominant mechanism when the AlN thickness increases up to 5 nm. X-ray photoelectron spectroscopy (XPS) characterizations reveal the type I alignment for AlN/$\beta $ -Ga2O3 heterojunction with a large conduction band offset ($\Delta {E}_{C}$ ) of 1 eV, which could function as an electron transport barrier under reverse conditions, thereby greatly suppressing the leakage current. Our study for the first time suggests a great potential for ALD-derived AlN films to be an interfacial layer in$\beta $ -Ga2O3 SBDs and the AlN/$\beta $ -Ga2O3 SBDs with state-of-art performances open up more opportunities in future power electronics.- 9 October 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 71 (11) , 6934-6941
Low Turn-On Voltage and Reverse Leakage Current β -Ga2O3 MIS Schottky Barrier Diodes With an AlN Interfacial Layer
We demonstrate for the first time a vertical metal/AlN/$\beta $ -gallium oxide ($\beta $ -Ga2O3) metal-insulator–semiconductor (MIS) Schottky barrier diode (SBD) with low turn-on voltage (${V}_{\text {on}}$ ) and reverse leakage current. By employing an ultrathin AlN layer enabled by atomic layer deposition (ALD), the resulting AlN/$\beta $ -Ga2O3 MIS SBD exhibits a remarkably low leakage current of$0.1~\mu $ A/cm2, which is three orders of magnitude smaller than that of the conventional$\beta $ -Ga2O3 SBD. Meanwhile, the AlN/$\beta $ -Ga2O3 MIS SBD shows a significantly improved breakdown voltage from 208 V up to 890 V, while maintaining a relatively low${V}_{\text {on}}$ of 0.92 V and on-resistance (${R}_{\text {on}}$ ) of 11.8 m$\Omega \cdot $ cm2, respectively. I–V measurements conducted across a range of temperatures from 298 to 432 K indicate that thermionic field emission (TFE) and trap-assisted tunneling (TAT) are the predominant electron transport mechanisms under forward bias if inserting 2 nm AlN, while TFE becomes dominant mechanism when the AlN thickness increases up to 5 nm. X-ray photoelectron spectroscopy (XPS) characterizations reveal the type I alignment for AlN/$\beta $ -Ga2O3 heterojunction with a large conduction band offset ($\Delta {E}_{C}$ ) of 1 eV, which could function as an electron transport barrier under reverse conditions, thereby greatly suppressing the leakage current. Our study for the first time suggests a great potential for ALD-derived AlN films to be an interfacial layer in$\beta $ -Ga2O3 SBDs and the AlN/$\beta $ -Ga2O3 SBDs with state-of-art performances open up more opportunities in future power electronics.