Le An
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Le An has a total of 9 co-authors. Here are the top co-authors by number of shared publications:
- Heshan Bai
State Key Laboratory for Strength and Vibration of Mechanical Structures, School of Aerospace Engineering Xi'an Jiaotong University Xi'an China
3 shared publications Chenyu Jin
2 shared publications- Rui Xiang2 shared publications
- Wenzhe Zhao
State Key Laboratory for Strength and Vibration of Mechanical Structures, Department of Engineering Mechanics, Xi’an Jiaotong University, Xi’an 710049, China
2 shared publications - Shujuan Wang
Xi’an Jiaotong University
1 shared publication Wenzhe Zhao
1 shared publication
Latest Publications
- 23 August 2022
- Published by Elsevier in Materials Letters
- Vol. 328
Surface degradation assisted welding for vitrimer composites
- 23 August 2022
- Published by Elsevier in Materials Letters
- Vol. 328
Surface degradation assisted welding for vitrimer composites
- Open Access
Facile Surface Depolymerization Promotes the Welding of Hard Epoxy Vitrimer
Welding via bond exchange reactions has provided advances in obtaining high-quality joining performance. However, the reported welding method requires a relatively high press force, and challenges are still encountered in welding hard vitrimer. In this work, a facile surface depolymerization strategy was introduced to weld high-performance epoxy vitrimer. The vitrimers were firstly dissolved into ethylene glycol for depolymerization based on the solvent-assisted bond exchange reactions. Then, the depolymerized vitrimers were welded under heat and press force. The effect of the depolymerizing time, welding pressure, welding temperature and welding time on the welding strength were further investigated. It was found that there were optimal values for the depolymerizing time, welding pressure, and welding temperature, respectively, for the welding strength, while the welding strength increased with increasing welding time. Through facile surface degradation, the welding pressure was highly reduced, while the welding strength was increased. With surface depolymerization, the welding strength was 1.55-times higher, but the magnitude of press force was 1/1000-times than that with no surface depolymerization. It is elucidative that surface depolymerization can be used to weld hard vitrimer composites alongside reducing the press force effectively.
Open AccessFacile Surface Depolymerization Promotes the Welding of Hard Epoxy Vitrimer
Welding via bond exchange reactions has provided advances in obtaining high-quality joining performance. However, the reported welding method requires a relatively high press force, and challenges are still encountered in welding hard vitrimer. In this work, a facile surface depolymerization strategy was introduced to weld high-performance epoxy vitrimer. The vitrimers were firstly dissolved into ethylene glycol for depolymerization based on the solvent-assisted bond exchange reactions. Then, the depolymerized vitrimers were welded under heat and press force. The effect of the depolymerizing time, welding pressure, welding temperature and welding time on the welding strength were further investigated. It was found that there were optimal values for the depolymerizing time, welding pressure, and welding temperature, respectively, for the welding strength, while the welding strength increased with increasing welding time. Through facile surface degradation, the welding pressure was highly reduced, while the welding strength was increased. With surface depolymerization, the welding strength was 1.55-times higher, but the magnitude of press force was 1/1000-times than that with no surface depolymerization. It is elucidative that surface depolymerization can be used to weld hard vitrimer composites alongside reducing the press force effectively.
- Open Access
Recyclable High-Performance Epoxy-Anhydride Resins with DMP-30 as the Catalyst of Transesterification Reactions
Epoxy-anhydride resins are widely used in engineering fields due to their excellent performance. However, the insolubility and infusibility make the recycling of epoxy resins challenging. The development of degradable epoxy resins with stable covalent networks provides an efficient solution to the recycling of thermosets. In this paper, 2,4,6-tris(dimethylaminomethyl)phenol (DMP-30) is incorporated into the epoxy-glutaric anhydride (GA) system to prepare high-performance epoxy resins that can be recycled below 200 °C at ordinary pressure via ethylene glycol (EG) participated transesterification. The tertiary amine groups in DMP-30 can catalyze the curing reaction of epoxy and anhydride, as well as the transesterification between ester bonds and alcoholic hydroxyl groups. Compared with early recyclable anhydride-cured epoxy resins, the preparation and recycling of diglycidyl ether of bisphenol A (DGEBA)/GA/DMP-30 systems do not need any special catalysts such as TBD, Zn(Ac)2, etc., which are usually expensive, toxic, and have poor compatibility with other compounds. The resulting resins have glass transition temperatures and strengths similar to those of conventional epoxy resins. The influences of GA content, DMP-30 content, and temperature on the dissolution rate were studied. The decomposed epoxy oligomer (DEO) is further used as a reaction ingredient to prepare new resins. It is found that the DEO can improve the toughness of epoxy resins significantly. This work provides a simple method to prepare readily recyclable epoxy resins, which is of low-cost and easy to implement.
Open AccessRecyclable High-Performance Epoxy-Anhydride Resins with DMP-30 as the Catalyst of Transesterification Reactions
Epoxy-anhydride resins are widely used in engineering fields due to their excellent performance. However, the insolubility and infusibility make the recycling of epoxy resins challenging. The development of degradable epoxy resins with stable covalent networks provides an efficient solution to the recycling of thermosets. In this paper, 2,4,6-tris(dimethylaminomethyl)phenol (DMP-30) is incorporated into the epoxy-glutaric anhydride (GA) system to prepare high-performance epoxy resins that can be recycled below 200 °C at ordinary pressure via ethylene glycol (EG) participated transesterification. The tertiary amine groups in DMP-30 can catalyze the curing reaction of epoxy and anhydride, as well as the transesterification between ester bonds and alcoholic hydroxyl groups. Compared with early recyclable anhydride-cured epoxy resins, the preparation and recycling of diglycidyl ether of bisphenol A (DGEBA)/GA/DMP-30 systems do not need any special catalysts such as TBD, Zn(Ac)2, etc., which are usually expensive, toxic, and have poor compatibility with other compounds. The resulting resins have glass transition temperatures and strengths similar to those of conventional epoxy resins. The influences of GA content, DMP-30 content, and temperature on the dissolution rate were studied. The decomposed epoxy oligomer (DEO) is further used as a reaction ingredient to prepare new resins. It is found that the DEO can improve the toughness of epoxy resins significantly. This work provides a simple method to prepare readily recyclable epoxy resins, which is of low-cost and easy to implement.