Hojjat Mousavi
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Hojjat Mousavi has a total of 20 co-authors. Here are the top co-authors by number of shared publications:
- Aneta Ustrzycka
Institute of Fundamental Technological Research, Polish Academy of Sciences, Warsaw
2 shared publications - Stanislaw Stupkiewicz
Institute of Fundamental Technological Research (IPPT) Polish Academy of Sciences Pawińskiego 5B 02-106 Warsaw Poland
2 shared publications - Ahmad Varvani-Farahani
Department of Mechanical, Industrial, and Mechatronics Engineering, Toronto Metropolitan University, Toronto, ON M5B 2K3, Canada
1 shared publication - Cyrus Amini
Mechanical Engineering Department, University of Tabriz, Tabriz, Iran
1 shared publication Diego Rivas López
1 shared publicationEhsan Entezari
1 shared publication
Latest Publications
- 26 March 2026
- Published by Elsevier in International Journal of Plasticity
- Vol. 201
Molecular dynamics study of the role of anisotropy in radiation-driven embrittlement
- 26 March 2026
- Published by Elsevier in International Journal of Plasticity
- Vol. 201
Molecular dynamics study of the role of anisotropy in radiation-driven embrittlement
- Open Access
- 16 July 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 303
Atomistic study of radiation-induced ductile-to-brittle transition in austenitic steel
- 16 July 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 303
Open AccessAtomistic study of radiation-induced ductile-to-brittle transition in austenitic steel
- Open Access
Ball Burnishing of Friction Stir Welded Aluminum Alloy 2024-T3: Experimental and Numerical Studies
This paper deals with the improvement of the material surface state of friction stir welding paths modified in situ by plastic deformation through ball burnishing. The metallurgical and topological states of materials joined by this welding technique are typically detrimental to the ulterior performance of the workpiece, and it is believed that ball burnishing can improve these states to enhance functioning. This study is divided into two phases. The first one is experimental and consists of welding aluminum AA2024-T3 plates while combining different tool rotations and welding speeds. Then, the welding line is deformed locally by ball burnishing. The improvement of the topology and deep hardness distribution is measured and discussed, and the evolution of mechanical properties is assessed through tensile tests. The second phase is oriented towards estimating the residual stresses by combining two pre-existing models of friction stir welding and burnishing developed by the same authors using ANSYS®. Friction stir welding experimentation and measurements show a decrease in the values of all measured mechanical properties compared to the original material. The dominant factor affecting the properties and texture of the materials is the rotational speed of the tool, with the rupture point in the tensile test located in the distinct zone with the lowest value of microhardness on the advancing side. The higher the ratio of the rotational speed to the welding speed, the lower the roughness value. Finally, ball burnishing is proven to be an effective method to enhance the surface integrity of friction stir welded joints in light of the results, achieving a reduction of 11% to 36% in average roughness and an increase of about 22% in hardness profile, along with an integrated numerical model estimation of a remarkable effect on compressive residual stresses in-depth on the retreating side of the welded samples. However, in some tests, this treatment reduced some characteristics (yield stress and failure strain).
Open AccessBall Burnishing of Friction Stir Welded Aluminum Alloy 2024-T3: Experimental and Numerical Studies
This paper deals with the improvement of the material surface state of friction stir welding paths modified in situ by plastic deformation through ball burnishing. The metallurgical and topological states of materials joined by this welding technique are typically detrimental to the ulterior performance of the workpiece, and it is believed that ball burnishing can improve these states to enhance functioning. This study is divided into two phases. The first one is experimental and consists of welding aluminum AA2024-T3 plates while combining different tool rotations and welding speeds. Then, the welding line is deformed locally by ball burnishing. The improvement of the topology and deep hardness distribution is measured and discussed, and the evolution of mechanical properties is assessed through tensile tests. The second phase is oriented towards estimating the residual stresses by combining two pre-existing models of friction stir welding and burnishing developed by the same authors using ANSYS®. Friction stir welding experimentation and measurements show a decrease in the values of all measured mechanical properties compared to the original material. The dominant factor affecting the properties and texture of the materials is the rotational speed of the tool, with the rupture point in the tensile test located in the distinct zone with the lowest value of microhardness on the advancing side. The higher the ratio of the rotational speed to the welding speed, the lower the roughness value. Finally, ball burnishing is proven to be an effective method to enhance the surface integrity of friction stir welded joints in light of the results, achieving a reduction of 11% to 36% in average roughness and an increase of about 22% in hardness profile, along with an integrated numerical model estimation of a remarkable effect on compressive residual stresses in-depth on the retreating side of the welded samples. However, in some tests, this treatment reduced some characteristics (yield stress and failure strain).
- 1 September 2020
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 45 (43) , 23122-23133
Finite element modeling of HIC propagation in pipeline steel with regard to experimental observations
- 1 September 2020
- Published by Elsevier in International Journal of Hydrogen Energy
- Vol. 45 (43) , 23122-23133
Finite element modeling of HIC propagation in pipeline steel with regard to experimental observations
- 11 November 2018
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 42 (3) , 764-772
The influence of low-plasticity burnishing process on the fatigue life of friction-stir-processed Al 7075-T6 samples
The effects of low‐plasticity burnishing (LPB) on the fatigue life of friction‐stir‐processed (FSP) Al 7075‐T6 plates were examined experimentally and numerically. Aluminum samples were taken from plates to test fatigue response in the presence of heat‐affected zone (HAZ) at different loading magnitudes. Finite element method was employed to numerically evaluate fatigue life of FSPed samples by means of the Smith–Watson–Topper (SWT) model. Through numerical analysis, the FSP and its cooling procedure were modelled on the basis of the arbitrary Lagrangian–Eulerian technique, and then, the effect of the LPB to assess fatigue response of samples was examined. Aluminum samples undergoing friction‐stir process presented lower‐fatigue life as stresses were highly concentrated within FSP regions. Involvement of LPB regained fatigue durability through compressive residual stress induced on the aluminum samples. The higher applied force over the LPB promoted compressive residual stress on the sample surface and improved fatigue life of samples. The predicted life results were found twice more in magnitude than those of experimentally obtained.
- 11 November 2018
- Published by Wiley in Fatigue & Fracture of Engineering Materials & Structures
- Vol. 42 (3) , 764-772
The influence of low-plasticity burnishing process on the fatigue life of friction-stir-processed Al 7075-T6 samples
The effects of low‐plasticity burnishing (LPB) on the fatigue life of friction‐stir‐processed (FSP) Al 7075‐T6 plates were examined experimentally and numerically. Aluminum samples were taken from plates to test fatigue response in the presence of heat‐affected zone (HAZ) at different loading magnitudes. Finite element method was employed to numerically evaluate fatigue life of FSPed samples by means of the Smith–Watson–Topper (SWT) model. Through numerical analysis, the FSP and its cooling procedure were modelled on the basis of the arbitrary Lagrangian–Eulerian technique, and then, the effect of the LPB to assess fatigue response of samples was examined. Aluminum samples undergoing friction‐stir process presented lower‐fatigue life as stresses were highly concentrated within FSP regions. Involvement of LPB regained fatigue durability through compressive residual stress induced on the aluminum samples. The higher applied force over the LPB promoted compressive residual stress on the sample surface and improved fatigue life of samples. The predicted life results were found twice more in magnitude than those of experimentally obtained.