Xueyan Wang
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Xueyan Wang has a total of 13 co-authors. Here are the top co-authors by number of shared publications:
Jian Yang
Hebei Construction Group Co., Ltd, Shijiazhuang, China
4 shared publicationsJianhui An
Hebei Construction Group Co., Ltd, Shijiazhuang, China
4 shared publicationsWenlong Cao
Department of Road and Bridge Engineering, Hebei Jiaotong Vocational and Technical College, Shijiazhuang, China
4 shared publications- Jianqing Bu
State Key Laboratory of Mechanical Behavior and System Safety of Traffic Engineering Structures, Shijiazhuang Tiedao University, Shijiazhuang 050043, China
2 shared publications - Wenlong Cao
School of Civil Engineering, Shijiazhuang Tiedao University, Shijiazhuang, China
2 shared publications Yanzhen Jia
Department of Road and Bridge Engineering, Hebei Jiaotong Vocational and Technical College, Shijiazhuang, China
2 shared publications
Latest Publications
- Open Access
- 24 October 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-25
Study on wind load characteristics of gable roof under tornado
This research simulates the behavior of a tornado on a double-slope roof using the Ward tornado generator and the \(SS{T_{k - \omega }}\) turbulence model. The effects of different ground roughness, slope angle, and wind field position on the tornado load characteristics of gable roofs were studied. The tornado-generating device established the tornado field under various working conditions, and the simulation results were compared with the experimental data to verify the reliability of the simulation results. The wind pressure distribution of gable roofs with four different slope angles was analyzed to find the most unfavorable roof condition of the tornado field. The gable roof’s aerodynamic and wind pressure characteristics at various places in the tornado field were explored by comparing the wind pressure coefficients at five distinct positions on smooth and rough ground. The lift-drag and wind pressure coefficients of five kinds of ground roughness were calculated to determine the influence of different ground roughness on the aerodynamic force and partial pressure distribution of the gable roof. The ground roughness reduces the vortex ratio because the ground roughness reduces the maximum tangential wind speed and the radius of the vortex core. Therefore, the gable roof’s suction increases as the updraft increases.- 24 October 2024
- Published by Springer Nature in Scientific Reports
- Vol. 14 (1) , 1-25
Open AccessStudy on wind load characteristics of gable roof under tornado
This research simulates the behavior of a tornado on a double-slope roof using the Ward tornado generator and the \(SS{T_{k - \omega }}\) turbulence model. The effects of different ground roughness, slope angle, and wind field position on the tornado load characteristics of gable roofs were studied. The tornado-generating device established the tornado field under various working conditions, and the simulation results were compared with the experimental data to verify the reliability of the simulation results. The wind pressure distribution of gable roofs with four different slope angles was analyzed to find the most unfavorable roof condition of the tornado field. The gable roof’s aerodynamic and wind pressure characteristics at various places in the tornado field were explored by comparing the wind pressure coefficients at five distinct positions on smooth and rough ground. The lift-drag and wind pressure coefficients of five kinds of ground roughness were calculated to determine the influence of different ground roughness on the aerodynamic force and partial pressure distribution of the gable roof. The ground roughness reduces the vortex ratio because the ground roughness reduces the maximum tangential wind speed and the radius of the vortex core. Therefore, the gable roof’s suction increases as the updraft increases. - Open Access
- 16 October 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-15
Large eddy simulation on wind-induced interference effects of staggered chamfered square cylinders
Chamfered corners in buildings are the main means to reduce the control effect of wind load on the structure, and the interference effect of chamfered buildings cannot be ignored. At present, only the mutual interference coefficients of square and rectangular section buildings are given in the Chinese code, without the interference effect of chamfered buildings being specified. Therefore, in this paper, aerodynamic force and wind pressure coefficients of chamfered square cylinders of different spacing are obtained by the large eddy simulation method. Wind load characteristics, non-Gaussian characteristics and interference effects of chamfered square cylinders with different arrangements are studied based on aerodynamic coefficients, wind pressure coefficients and interference coefficients. The results show that when the wall y plus value is 1, the large eddy simulation is the most accurate to simulate the wind load and wind field parameters. Besides, the aerodynamic effects, non-Gaussian characteristics and interference effects between the chamfered square cylinders are mainly controlled by the cross-wind interval and the spacing (4.0, 4.0) is the characteristic coordinate. That means, when the spacing is smaller than this coordinate, the interference effect of the square cylinder is more obvious. When the spacing coordinate is greater than (4.0, 4.0), the aerodynamic coefficients and non-Gaussian regional distributions of the principal square cylinder and the isolated cylinder are the same, and the interference factor approaches 1.
- 16 October 2023
- Published by Springer Nature in Scientific Reports
- Vol. 13 (1) , 1-15
Open AccessLarge eddy simulation on wind-induced interference effects of staggered chamfered square cylinders
Chamfered corners in buildings are the main means to reduce the control effect of wind load on the structure, and the interference effect of chamfered buildings cannot be ignored. At present, only the mutual interference coefficients of square and rectangular section buildings are given in the Chinese code, without the interference effect of chamfered buildings being specified. Therefore, in this paper, aerodynamic force and wind pressure coefficients of chamfered square cylinders of different spacing are obtained by the large eddy simulation method. Wind load characteristics, non-Gaussian characteristics and interference effects of chamfered square cylinders with different arrangements are studied based on aerodynamic coefficients, wind pressure coefficients and interference coefficients. The results show that when the wall y plus value is 1, the large eddy simulation is the most accurate to simulate the wind load and wind field parameters. Besides, the aerodynamic effects, non-Gaussian characteristics and interference effects between the chamfered square cylinders are mainly controlled by the cross-wind interval and the spacing (4.0, 4.0) is the characteristic coordinate. That means, when the spacing is smaller than this coordinate, the interference effect of the square cylinder is more obvious. When the spacing coordinate is greater than (4.0, 4.0), the aerodynamic coefficients and non-Gaussian regional distributions of the principal square cylinder and the isolated cylinder are the same, and the interference factor approaches 1.
- Open Access
- 15 September 2023
- Published by Springer Nature in Research Square
Large eddy simulation on wind-induced interference effects of staggered chamfered square cylinders
Chamfered corners in buildings are the main means to reduce the control effect of wind load on the structure, and the interference effect of chamfered buildings cannot be ignored. At present, only the mutual interference coefficients of square and rectangular section buildings are given in the Chinese code, without the interference effect of chamfered buildings being specified. Therefore, in this paper, aerodynamic force and wind pressure coefficients of chamfered square cylinders of different spacing are obtained by the large eddy simulation method. Wind load characteristics, non-Gaussian characteristics and interference effects of chamfered square cylinders with different arrangements are studied based on aerodynamic coefficients, wind pressure coefficients and interference coefficients. The results show that when the wall y plus value is 1, the large eddy simulation is the most accurate to simulate the wind load and wind field parameters. Besides, the aerodynamic effects, non-Gaussian characteristics and interference effects between the chamfered square cylinders are mainly controlled by the cross-wind interval and the spacing (4.0, 4.0) is the characteristic coordinate. That means, when the spacing is smaller than this co-ordinate, the interference effect of the square cylinder is more obvious. When the spacing coordinate is greater than (4.0, 4.0), the aerodynamic coefficients and non-Gaussian regional distributions of the principal square cylinder and the isolated cylinder are the same, and the interference factor approaches 1.
- 15 September 2023
- Published by Springer Nature in Research Square
Open AccessLarge eddy simulation on wind-induced interference effects of staggered chamfered square cylinders
Chamfered corners in buildings are the main means to reduce the control effect of wind load on the structure, and the interference effect of chamfered buildings cannot be ignored. At present, only the mutual interference coefficients of square and rectangular section buildings are given in the Chinese code, without the interference effect of chamfered buildings being specified. Therefore, in this paper, aerodynamic force and wind pressure coefficients of chamfered square cylinders of different spacing are obtained by the large eddy simulation method. Wind load characteristics, non-Gaussian characteristics and interference effects of chamfered square cylinders with different arrangements are studied based on aerodynamic coefficients, wind pressure coefficients and interference coefficients. The results show that when the wall y plus value is 1, the large eddy simulation is the most accurate to simulate the wind load and wind field parameters. Besides, the aerodynamic effects, non-Gaussian characteristics and interference effects between the chamfered square cylinders are mainly controlled by the cross-wind interval and the spacing (4.0, 4.0) is the characteristic coordinate. That means, when the spacing is smaller than this co-ordinate, the interference effect of the square cylinder is more obvious. When the spacing coordinate is greater than (4.0, 4.0), the aerodynamic coefficients and non-Gaussian regional distributions of the principal square cylinder and the isolated cylinder are the same, and the interference factor approaches 1.
- Open Access
- 4 August 2023
- Published by Springer Nature in Research Square
Evaluation of tornado loads on double-sloped roofs at various ground roughness and positions by numerical Ward-type tornado simulation
The effect of various slope angles, ground roughness and positions on tornado loading characteristics of double-sloped roof is identified through Ward-type tornado numerical simulation. Tornado fields under multiple operating conditions are established through a numerical Ward-type tornado generation apparatus and the reliability is verified by comparing simulation results with experimental data. A comparison of wind pressure distribution for double-sloped roofs with four different angles is used to determine the most unfavourable roof conditions for a tornado field. The wind pressure characteristics of double-sloped roofs at different locations in a tornado field is examined by comparing the wind pressure coefficients at five different locations on smooth and rough ground. Calculations of wind pressure coefficients for five ground roughness are carried out to identify the effect of different ground roughness on wind pressure distribution in roofs. Vortex volumes at different locations are calculated and analyzed to further verify the relationship between the wind pressure characteristics at different locations. This study sheds light on tornado loads on double-sloped roofs at various ground roughness and positions, and helps to clarify the mechanical properties, unfavourable locations and wind resistance design of double-sloped roofs under tornado action.
- 4 August 2023
- Published by Springer Nature in Research Square
Open AccessEvaluation of tornado loads on double-sloped roofs at various ground roughness and positions by numerical Ward-type tornado simulation
The effect of various slope angles, ground roughness and positions on tornado loading characteristics of double-sloped roof is identified through Ward-type tornado numerical simulation. Tornado fields under multiple operating conditions are established through a numerical Ward-type tornado generation apparatus and the reliability is verified by comparing simulation results with experimental data. A comparison of wind pressure distribution for double-sloped roofs with four different angles is used to determine the most unfavourable roof conditions for a tornado field. The wind pressure characteristics of double-sloped roofs at different locations in a tornado field is examined by comparing the wind pressure coefficients at five different locations on smooth and rough ground. Calculations of wind pressure coefficients for five ground roughness are carried out to identify the effect of different ground roughness on wind pressure distribution in roofs. Vortex volumes at different locations are calculated and analyzed to further verify the relationship between the wind pressure characteristics at different locations. This study sheds light on tornado loads on double-sloped roofs at various ground roughness and positions, and helps to clarify the mechanical properties, unfavourable locations and wind resistance design of double-sloped roofs under tornado action.
- Open Access
Experimental Research on the Mechanical Properties of MURSP-Type Steel-Concrete Composite Beams in Negative-Moment Region
To verify the effectiveness of uplift-restricted and slip-permitted (URSP) connectors in alleviating crack formation in the negative-moment region of steel-concrete composite beams (SCCBs) and improve the engineering adaptability of URSP connectors, this paper proposes a modified uplift-restricted and slip-permitted (MURSP) connector. Static load tests and theoretical analysis were conducted on two overhanging beams with MURSP connectors and ordinary studs to analyze the influence of different stud forms on the deflection, crack, and slip of SCCBs in the negative-moment region. Finally, a nonlinear finite element modeling method for MURSP-type steel-concrete composite beams was developed, and a finite element model was established. The results showed that the use of MURSP connectors could effectively alleviate the concrete cracking problem in the negative-moment zone of SCCBs. Compared with the common stud SCCB, the crack load of the MURSP-type SCCB was higher, the maximum crack width was lower, and the crack distribution was more uniform; however, the overall flexural stiffness of the overhanging beam with MURSP connectors was reduced by 3.08%. The interface slip of the overhanging beam with the MURSP connectors increased suddenly in the initial stage of loading, whereas the increase was more gradual in the later stage. The SCCB model established in this study was in good agreement with the results of experimental beams. The finite element analysis results showed that the ordinary stud and MURSP connector exhibited different stress and deformation states in the negative-moment region of SCCBs, and the deformation states changed from bending type to shear type.
Open AccessExperimental Research on the Mechanical Properties of MURSP-Type Steel-Concrete Composite Beams in Negative-Moment Region
To verify the effectiveness of uplift-restricted and slip-permitted (URSP) connectors in alleviating crack formation in the negative-moment region of steel-concrete composite beams (SCCBs) and improve the engineering adaptability of URSP connectors, this paper proposes a modified uplift-restricted and slip-permitted (MURSP) connector. Static load tests and theoretical analysis were conducted on two overhanging beams with MURSP connectors and ordinary studs to analyze the influence of different stud forms on the deflection, crack, and slip of SCCBs in the negative-moment region. Finally, a nonlinear finite element modeling method for MURSP-type steel-concrete composite beams was developed, and a finite element model was established. The results showed that the use of MURSP connectors could effectively alleviate the concrete cracking problem in the negative-moment zone of SCCBs. Compared with the common stud SCCB, the crack load of the MURSP-type SCCB was higher, the maximum crack width was lower, and the crack distribution was more uniform; however, the overall flexural stiffness of the overhanging beam with MURSP connectors was reduced by 3.08%. The interface slip of the overhanging beam with the MURSP connectors increased suddenly in the initial stage of loading, whereas the increase was more gradual in the later stage. The SCCB model established in this study was in good agreement with the results of experimental beams. The finite element analysis results showed that the ordinary stud and MURSP connector exhibited different stress and deformation states in the negative-moment region of SCCBs, and the deformation states changed from bending type to shear type.
- Open Access
- 28 August 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-12
Stiffness Calculation for Negative Moment Region of Steel-Concrete Composite Beams considering the Influence of Cracking and Interface Slip
Concrete cracking and interface slip decrease the bending stiffness of steel-concrete composite beams (SCCBs) in the negative moment region. To evaluate this decrease in the stiffness of SCCBs, a static differential equation is used to derive analytical expressions of interface slip and deflection. Based on the static load test results for SCCBs, the influence of concrete cracking and interface slip on the stiffness is analyzed. A linear stiffness reduction method is proposed for calculating the stiffness of SCCBs in the negative moment region after the concrete undergoes cracking. The proposed method can be used in engineering applications as it enables the facile and accurate calculation of the deflection and slip and the changes in stiffness of SCCBs in the negative moment region. The method can also be used for predicting and evaluating performance in the field of structural design.
- 28 August 2022
- Published by Wiley in Advances in Materials Science and Engineering
- Vol. 2022, 1-12
Open AccessStiffness Calculation for Negative Moment Region of Steel-Concrete Composite Beams considering the Influence of Cracking and Interface Slip
Concrete cracking and interface slip decrease the bending stiffness of steel-concrete composite beams (SCCBs) in the negative moment region. To evaluate this decrease in the stiffness of SCCBs, a static differential equation is used to derive analytical expressions of interface slip and deflection. Based on the static load test results for SCCBs, the influence of concrete cracking and interface slip on the stiffness is analyzed. A linear stiffness reduction method is proposed for calculating the stiffness of SCCBs in the negative moment region after the concrete undergoes cracking. The proposed method can be used in engineering applications as it enables the facile and accurate calculation of the deflection and slip and the changes in stiffness of SCCBs in the negative moment region. The method can also be used for predicting and evaluating performance in the field of structural design.