Hassan Sahsah
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Hassan Sahsah has a total of 15 co-authors. Here are the top co-authors by number of shared publications:
- Abdelaaziz Benahmida
Ibn Zohr University
2 shared publications - Abdellah Amghar
Ibn Zohr University
2 shared publications - Kawtar Tifidat
Laboratory of Materials, Signals, Systems and Physical Modeling, Department of Physics, Faculty of Sciences, Ibn Zohr University, B.P. 8106, Agadir 80000, Morocco
2 shared publications - Noureddine Maouhoub
Ibn Zohr University
2 shared publications A. Amghar
1 shared publicationF. Bakkali
1 shared publication
Latest Publications
- Open Access
- 1 June 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (2) , 1284-1297
A novel temperature parametric method for rapid maximum power point detection in photovoltaic modules
Photovoltaic systems (PVS) exhibit variability in their maximum power point (MPP) output due to variations in irradiance and cell temperature. This can lead to reduced efficiency, as maximum power point tracking (MPPT) algorithms often have slow response times and limited ability to adapt to rapidly changing environmental conditions. New algorithms are therefore needed to capture more energy and improve the efficiency of these systems. In this context, this article presents a new method for temperature parametric (TP) and its implementation using a digital PI controller, a buck converter, and MATLAB-Simulink. This innovative approach relies on detecting the MPP by continuously measuring the cell temperature of the PV panel (𝑇𝑐𝑒𝑙𝑙) and solar irradiance (S). A 3D linear regression model connects these two parameters with the maximum current (𝐼𝑚𝑝𝑝), enabling real-time monitoring of the MPP. We have applied this new method on two different types of PV (POLY-40W and BPSX330J) under a range of environmental conditions, including stable and dynamic scenarios. The results of the simulation demonstrate the superiority of our approach compared to the hill climbing (HC) for perturbation steps of HC (1%) and HC (2%). Our method achieves faster convergence time 0.009 s and high MPPT efficiency at 98.18%, fewer steady-state oscillations, and better detection.
- 1 June 2025
- Published by Institute of Advanced Engineering and Science in International Journal of Power Electronics and Drive Systems (IJPEDS)
- Vol. 16 (2) , 1284-1297
Open AccessA novel temperature parametric method for rapid maximum power point detection in photovoltaic modules
Photovoltaic systems (PVS) exhibit variability in their maximum power point (MPP) output due to variations in irradiance and cell temperature. This can lead to reduced efficiency, as maximum power point tracking (MPPT) algorithms often have slow response times and limited ability to adapt to rapidly changing environmental conditions. New algorithms are therefore needed to capture more energy and improve the efficiency of these systems. In this context, this article presents a new method for temperature parametric (TP) and its implementation using a digital PI controller, a buck converter, and MATLAB-Simulink. This innovative approach relies on detecting the MPP by continuously measuring the cell temperature of the PV panel (𝑇𝑐𝑒𝑙𝑙) and solar irradiance (S). A 3D linear regression model connects these two parameters with the maximum current (𝐼𝑚𝑝𝑝), enabling real-time monitoring of the MPP. We have applied this new method on two different types of PV (POLY-40W and BPSX330J) under a range of environmental conditions, including stable and dynamic scenarios. The results of the simulation demonstrate the superiority of our approach compared to the hill climbing (HC) for perturbation steps of HC (1%) and HC (2%). Our method achieves faster convergence time 0.009 s and high MPPT efficiency at 98.18%, fewer steady-state oscillations, and better detection.
- Open Access
- 1 October 2022
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 12 (5) , 4529-4537
Extraction of photovoltaic generator parameters through combination of an analytical and iterative approach
In the present work, we propose an improved method based on a combination of an analytical and iterative approach to extract the photovoltaic (PV) module parameters using the measured current-voltage characteristics and the simple diode model. First, we calculate the series resistance using a set of analytical formulas for the base values of the three current-voltage curves. Then, the three other parameters are analytically expressed as functions of serial resistance and ideality factor based on the linear least-squares method. Finally, the ideality factor is calculated applying an iterative algorithm to minimize the normalized root mean square error (NRMSE) value. The proposed method was validated with a real experimental set of two PV generators, which showed the best fit to the I-V curve. Moreover, the proposed method needs only the initial value of the ideality factor.
- 1 October 2022
- Published by Institute of Advanced Engineering and Science in International Journal of Electrical and Computer Engineering (IJECE)
- Vol. 12 (5) , 4529-4537
Open AccessExtraction of photovoltaic generator parameters through combination of an analytical and iterative approach
In the present work, we propose an improved method based on a combination of an analytical and iterative approach to extract the photovoltaic (PV) module parameters using the measured current-voltage characteristics and the simple diode model. First, we calculate the series resistance using a set of analytical formulas for the base values of the three current-voltage curves. Then, the three other parameters are analytically expressed as functions of serial resistance and ideality factor based on the linear least-squares method. Finally, the ideality factor is calculated applying an iterative algorithm to minimize the normalized root mean square error (NRMSE) value. The proposed method was validated with a real experimental set of two PV generators, which showed the best fit to the I-V curve. Moreover, the proposed method needs only the initial value of the ideality factor.
- 23 August 2022
- Published by Wiley in International Journal of Energy Research
- Vol. 46 (15) , 22795-22807
An accurate analytical model for predicting the maximum power of photovoltaic module operating outdoor under varying conditions
- 23 August 2022
- Published by Wiley in International Journal of Energy Research
- Vol. 46 (15) , 22795-22807
An accurate analytical model for predicting the maximum power of photovoltaic module operating outdoor under varying conditions
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 24, 125-129
The prediction of the maximum power of PV modules associated with a static converter under different environmental conditions
- 1 January 2020
- Published by Elsevier in Materials Today: Proceedings
- Vol. 24, 125-129
The prediction of the maximum power of PV modules associated with a static converter under different environmental conditions