Gabriele Melo de Andrade
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Gabriele Melo de Andrade has a total of 53 co-authors. Here are the top co-authors by number of shared publications:
- Rodolfo Giacomim Mendes de Andrade
Civil Engineering and Buildings Department, Instituto Federal do Espírito Santo, Av. Vitória, 1729, Vitória 29040-780, ES, Brazil
3 shared publications Thayrine Silva Matos
Departamento de Tecnologia e Recursos Naturais, Universidade do Estado do Pará, Campus VIII, 68503-120 Marabá, Pará, Brazil
3 shared publicationsJavan Pereira Motta
Departamento de Tecnologia e Recursos Naturais, Universidade do Estado do Pará, Campus VIII, 68503-120 Marabá, Pará, Brazil
2 shared publicationsLaise de Jesus dos Santos
Departamento de Tecnologia e Recursos Naturais, Universidade do Estado do Pará, Campus VIII, 68503-120 Marabá, Pará, Brazil
2 shared publications- Luiz Eduardo de Lima Melo
Universidade do Estado do Pará, Brazil
2 shared publications Marcelo Mendes Braga Júnior
Departamento de Tecnologia e Recursos Naturais, Universidade do Estado do Pará, Campus VIII, 68503-120 Marabá, Pará, Brazil
2 shared publications
Latest Publications
- Open Access
- 20 November 2025
- Published by Elsevier in Journal of Energy Storage
- Vol. 141
Thermal and mechanical performance of bio-concrete with phase change material-encapsulated lignocellulosic aggregates
- 20 November 2025
- Published by Elsevier in Journal of Energy Storage
- Vol. 141
Open AccessThermal and mechanical performance of bio-concrete with phase change material-encapsulated lignocellulosic aggregates
- 12 June 2025
- Published by Springer Nature
- p. 752-770
Coffee Husk (Coffea Arabica) Residue as a Bio-Aggregate for Lightweight Cement-Based Bio-Composites
- 12 June 2025
- Published by Springer Nature
- p. 752-770
Coffee Husk (Coffea Arabica) Residue as a Bio-Aggregate for Lightweight Cement-Based Bio-Composites
- Open Access
- 1 January 2025
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 31
Partial replacement of tannin with nanolignin in adhesive formulations for bonding plywood produced with Erythrina poeppigiana wood
Background: Fast-growing species are crucial for the wood panel market, and Erythrina poeppigiana (mulungu) emerges as a promising alternative. Although its wood is not suitable for high-performance applications, using its veneers for plywood supports the diversification of raw materials in forestry. Furthermore, replacing petrochemical-based adhesives is essential due to associated health and environmental risks. Tannins from forest species provide a sustainable alternative; however, their mechanical strength and moisture resistance must be improved. Nanolignin, a nanoscale additive, enhances these properties, making it a viable option for biodegradable adhesives. This study evaluates plywood production using E. poeppigiana veneers bonded with a tannin-nanolignin adhesive. Results: Adhesives were formulated with Acacia mearnsii* tannin partially replaced by nanolignin at different concentrations and tested for rheological properties. The wood, sourced from experimental plantations in Ilhéus, Bahia (Brazil), was processed into five-layer plywood panels bonded with 320 g/m² of natural adhesive and pressed at 150 °C and 1 MPa for 10 minutes. The resulting panels were evaluated for physical and mechanical properties, contact angle, scanning electron microscopy (SEM), acoustic insulation, and thermal conductivity. The results confirmed E. poeppigiana as a viable raw material for plywood production. Partial replacement of tannin with 1-2% nanolignin reduced adhesive viscosity, improving application and veneer penetration. The 2% nanolignin formulation increased hydrophobicity, reducing water absorption, while shear strength tests revealed higher cohesion and adhesion, particularly in adhesives containing 2-3% nanolignin. Conclusions: The findings demonstrate that E. poeppigiana veneers bonded with tannin-nanolignin adhesives can produce plywood panels with suitable physical and mechanical performance. The incorporation of small amounts of nanolignin enhances the adhesive’s rheological and bonding characteristics, contributing to improved durability and water resistance. These results support the potential use of E. poeppigian and nanolignin-modified tannins as sustainable materials in eco-friendly plywood manufacturing.
- 1 January 2025
- Published by FapUNIFESP (SciELO) in CERNE
- Vol. 31
Open AccessPartial replacement of tannin with nanolignin in adhesive formulations for bonding plywood produced with Erythrina poeppigiana wood
Background: Fast-growing species are crucial for the wood panel market, and Erythrina poeppigiana (mulungu) emerges as a promising alternative. Although its wood is not suitable for high-performance applications, using its veneers for plywood supports the diversification of raw materials in forestry. Furthermore, replacing petrochemical-based adhesives is essential due to associated health and environmental risks. Tannins from forest species provide a sustainable alternative; however, their mechanical strength and moisture resistance must be improved. Nanolignin, a nanoscale additive, enhances these properties, making it a viable option for biodegradable adhesives. This study evaluates plywood production using E. poeppigiana veneers bonded with a tannin-nanolignin adhesive. Results: Adhesives were formulated with Acacia mearnsii* tannin partially replaced by nanolignin at different concentrations and tested for rheological properties. The wood, sourced from experimental plantations in Ilhéus, Bahia (Brazil), was processed into five-layer plywood panels bonded with 320 g/m² of natural adhesive and pressed at 150 °C and 1 MPa for 10 minutes. The resulting panels were evaluated for physical and mechanical properties, contact angle, scanning electron microscopy (SEM), acoustic insulation, and thermal conductivity. The results confirmed E. poeppigiana as a viable raw material for plywood production. Partial replacement of tannin with 1-2% nanolignin reduced adhesive viscosity, improving application and veneer penetration. The 2% nanolignin formulation increased hydrophobicity, reducing water absorption, while shear strength tests revealed higher cohesion and adhesion, particularly in adhesives containing 2-3% nanolignin. Conclusions: The findings demonstrate that E. poeppigiana veneers bonded with tannin-nanolignin adhesives can produce plywood panels with suitable physical and mechanical performance. The incorporation of small amounts of nanolignin enhances the adhesive’s rheological and bonding characteristics, contributing to improved durability and water resistance. These results support the potential use of E. poeppigian and nanolignin-modified tannins as sustainable materials in eco-friendly plywood manufacturing.
- 28 October 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 451
Macauba (Acrocomia aculeata) endocarp as a coarse aggregate for bio-concretes
- 28 October 2024
- Published by Elsevier in Construction and Building Materials
- Vol. 451
Macauba (Acrocomia aculeata) endocarp as a coarse aggregate for bio-concretes
- Open Access
- 20 March 2023
- Published by Springer Nature in Research Square
Valorization of bean agricultural wastes for the production of polymeric composites
The objective of this study is to evaluate the characteristics of polymeric composites containing different bean residue levels for polymer replacement. To this end, agricultural residues were first reduced to particles and characterized "in natura" through tests for moisture content, bulk density, content of extractives, lignin and ash and by thermogravimetry technique. Then, particles of both materials were dried and selected based on their granulometric fractions to make low-density polyethylene (LDPE) composites with substitution levels of 0, 10, 20, 30 and 40% bean residues. The polymeric material and the bean stem and pod particles were hot-extruded to obtain strands and then pellets; the resulting materials were then molded and hot-pressed. After fabrication, the specimens were subjected to physical testing for humidity, density, water absorption, and flammability and to mechanical testing for tensile strength. Scanning electron microscopy (SEM) was performed to evaluate the fracture regions of the specimens that were broken during mechanical testing. The results indicated that the physical–mechanical properties of the composites were negatively affected by the characteristics of the lignocellulosic material and by the increased number of pores caused by the presence of the waste material.
- 20 March 2023
- Published by Springer Nature in Research Square
Open AccessValorization of bean agricultural wastes for the production of polymeric composites
The objective of this study is to evaluate the characteristics of polymeric composites containing different bean residue levels for polymer replacement. To this end, agricultural residues were first reduced to particles and characterized "in natura" through tests for moisture content, bulk density, content of extractives, lignin and ash and by thermogravimetry technique. Then, particles of both materials were dried and selected based on their granulometric fractions to make low-density polyethylene (LDPE) composites with substitution levels of 0, 10, 20, 30 and 40% bean residues. The polymeric material and the bean stem and pod particles were hot-extruded to obtain strands and then pellets; the resulting materials were then molded and hot-pressed. After fabrication, the specimens were subjected to physical testing for humidity, density, water absorption, and flammability and to mechanical testing for tensile strength. Scanning electron microscopy (SEM) was performed to evaluate the fracture regions of the specimens that were broken during mechanical testing. The results indicated that the physical–mechanical properties of the composites were negatively affected by the characteristics of the lignocellulosic material and by the increased number of pores caused by the presence of the waste material.
- Open Access
Bond Behavior of a Bio-Aggregate Embedded in Cement-Based Matrix
This paper investigates the bond behavior between a bio-aggregate and a cement-based matrix. The experimental evaluation comprised physical, chemical, image, and mechanical characterization of the bio-aggregate. The image analyses about the bio-aggregate’s outer structure provided first insights to understand the particularities of this newly proposed bio-aggregate for use in cementitious materials. A mineral aggregate (granitic rock), largely used as coarse aggregate in the Brazilian civil construction industry, was used as reference. The bond behavior of both aggregates was evaluated via pull-out tests. The results indicated that both aggregates presented a similar linear elastic branch up to each respective peak loads. The peak load magnitude of the mineral aggregate indicated a better chemical adhesion when compared to the bio-aggregate’s. The post-peak behavior, however, indicated a smoother softening branch for the bio-aggregate, corroborated by the microscopy image analyses. Although further investigation is required, the macaúba crushed endocarp was found to be a thriving bio-material to be used as bio-aggregate.
Open AccessBond Behavior of a Bio-Aggregate Embedded in Cement-Based Matrix
This paper investigates the bond behavior between a bio-aggregate and a cement-based matrix. The experimental evaluation comprised physical, chemical, image, and mechanical characterization of the bio-aggregate. The image analyses about the bio-aggregate’s outer structure provided first insights to understand the particularities of this newly proposed bio-aggregate for use in cementitious materials. A mineral aggregate (granitic rock), largely used as coarse aggregate in the Brazilian civil construction industry, was used as reference. The bond behavior of both aggregates was evaluated via pull-out tests. The results indicated that both aggregates presented a similar linear elastic branch up to each respective peak loads. The peak load magnitude of the mineral aggregate indicated a better chemical adhesion when compared to the bio-aggregate’s. The post-peak behavior, however, indicated a smoother softening branch for the bio-aggregate, corroborated by the microscopy image analyses. Although further investigation is required, the macaúba crushed endocarp was found to be a thriving bio-material to be used as bio-aggregate.
- 21 June 2022
- Published by Walter de Gruyter GmbH in IAWA Journal
- Vol. 43 (4) , 448-468
Use of wood by indigenous peoples of the Eastern Amazon, Brazil
Summary: The Brazilian Amazon has the world’s largest concentration of indigenous American peoples, but many environmental threats have affected the preservation of this enormous human ethnocultural heritage. This study identified the species and studied the different uses of wood by two indigenous ethnic groups in Southeastern Pará, Brazil, namely the “Gavião” and “Suruí”. Ten taxa were identified, distributed in eight botanical families, with five being identified to genus and five to species levels. The wood of Bertholletia excelsa, an endangered forest species in Brazil, is important in the material culture of the Suruí indigenous people. The indigenous ethnic groups studied preferentially use medium density wood for building and high-density wood for hunting and warfare artefacts. The technological properties of wood justify its use by the indigenous peoples studied. We caution that the increasing environmental threats in Indigenous Lands within the Brazilian Amazon harm the preservation of the ethnocultural heritage of indigenous peoples.
- 21 June 2022
- Published by Walter de Gruyter GmbH in IAWA Journal
- Vol. 43 (4) , 448-468
Use of wood by indigenous peoples of the Eastern Amazon, Brazil
Summary: The Brazilian Amazon has the world’s largest concentration of indigenous American peoples, but many environmental threats have affected the preservation of this enormous human ethnocultural heritage. This study identified the species and studied the different uses of wood by two indigenous ethnic groups in Southeastern Pará, Brazil, namely the “Gavião” and “Suruí”. Ten taxa were identified, distributed in eight botanical families, with five being identified to genus and five to species levels. The wood of Bertholletia excelsa, an endangered forest species in Brazil, is important in the material culture of the Suruí indigenous people. The indigenous ethnic groups studied preferentially use medium density wood for building and high-density wood for hunting and warfare artefacts. The technological properties of wood justify its use by the indigenous peoples studied. We caution that the increasing environmental threats in Indigenous Lands within the Brazilian Amazon harm the preservation of the ethnocultural heritage of indigenous peoples.
- 18 November 2021
- Published by CSIRO Publishing in Australian Journal of Botany
- Vol. 70 (1) , 13-31
Forestry control in the Brazilian Amazon: charcoal anatomy of tree species from protected areas
Protected areas in the Brazilian Amazon suffer from conflicting activities, such as the production of charcoal from illegal logging. Charcoal anatomy is an important tool that can be useful for forensic charcoal identification and to help the conservation of these areas. To assist in combating deforestation in protected areas, this study describes the charcoal anatomy of 14 tree species that occur in the Tapirapé–Aquiri National Forest, Pará, Brazil, and provides macrographs of transverse surfaces and scanning electron microscope (SEM) images to aid government agencies during surveillance. We adopted a carbonisation method that simulated real conditions. Anatomical features were well preserved in the charcoal. The axial parenchyma and vessel frequency are easily observed in both macrographs and SEM images, so they are important diagnostic features for initial screening of families and for checking the load according to the ‘document of forestry origin’ (DOF) by the surveillance agents. Uncommon and highly diagnostic features for distinguishing genera or even species, such as rays exclusively uniseriate, sheath cells, tile cells and storied structure, were observed only in SEM images. Our findings are suitable to provide a database on charcoal anatomy of native tree species of the Amazon, with practical application in government inspection activities in protected areas in Brazil and other countries with similar issues.
- 18 November 2021
- Published by CSIRO Publishing in Australian Journal of Botany
- Vol. 70 (1) , 13-31
Forestry control in the Brazilian Amazon: charcoal anatomy of tree species from protected areas
Protected areas in the Brazilian Amazon suffer from conflicting activities, such as the production of charcoal from illegal logging. Charcoal anatomy is an important tool that can be useful for forensic charcoal identification and to help the conservation of these areas. To assist in combating deforestation in protected areas, this study describes the charcoal anatomy of 14 tree species that occur in the Tapirapé–Aquiri National Forest, Pará, Brazil, and provides macrographs of transverse surfaces and scanning electron microscope (SEM) images to aid government agencies during surveillance. We adopted a carbonisation method that simulated real conditions. Anatomical features were well preserved in the charcoal. The axial parenchyma and vessel frequency are easily observed in both macrographs and SEM images, so they are important diagnostic features for initial screening of families and for checking the load according to the ‘document of forestry origin’ (DOF) by the surveillance agents. Uncommon and highly diagnostic features for distinguishing genera or even species, such as rays exclusively uniseriate, sheath cells, tile cells and storied structure, were observed only in SEM images. Our findings are suitable to provide a database on charcoal anatomy of native tree species of the Amazon, with practical application in government inspection activities in protected areas in Brazil and other countries with similar issues.
- Open Access
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Rodriguésia
- Vol. 71
Technological properties of woods used in boat’s production in the Southeast of Pará, Brazil
The aim of this study was to identify, anatomically characterize, and determine some of the physical properties of wood species that are used for boat production in the southeast region of the state of Pará in Brazil. The samples were collected during visits to shipyards in the region, then it was identified at the specie level and technologically characterized. Eight species belonging to four distinct botanical families were identified. All identified species had presented some type of deposition in its vessels and 87% of them had had medium density (0.40 to 0.75 g.cm-3). The species with higher frequency of occurrence and that had more parts used for boat production were Caryocar villosum and Apuleia leiocarpa. It was observed two different group arrangements of species, “piquiá” (Caryocar villosum and Alexa grandiflora) and “tatajuba” (Bagassa guianensis and Enterolobium schomburgkii). It was also identified the illegal commercialization of “castanheira’s” wood (Bertholletia excelsa). The results can indicate anatomical and physical similarities in woods used in boat production and can contribute as a component of a database in wood anatomy of specie used for boat production in the Amazon region, besides to subside practices that contribute to an effective supervision of the logging market in the region.
- 1 January 2020
- Published by FapUNIFESP (SciELO) in Rodriguésia
- Vol. 71
Open AccessTechnological properties of woods used in boat’s production in the Southeast of Pará, Brazil
The aim of this study was to identify, anatomically characterize, and determine some of the physical properties of wood species that are used for boat production in the southeast region of the state of Pará in Brazil. The samples were collected during visits to shipyards in the region, then it was identified at the specie level and technologically characterized. Eight species belonging to four distinct botanical families were identified. All identified species had presented some type of deposition in its vessels and 87% of them had had medium density (0.40 to 0.75 g.cm-3). The species with higher frequency of occurrence and that had more parts used for boat production were Caryocar villosum and Apuleia leiocarpa. It was observed two different group arrangements of species, “piquiá” (Caryocar villosum and Alexa grandiflora) and “tatajuba” (Bagassa guianensis and Enterolobium schomburgkii). It was also identified the illegal commercialization of “castanheira’s” wood (Bertholletia excelsa). The results can indicate anatomical and physical similarities in woods used in boat production and can contribute as a component of a database in wood anatomy of specie used for boat production in the Amazon region, besides to subside practices that contribute to an effective supervision of the logging market in the region.