Владимир Павлович Доронин
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Владимир Павлович Доронин has a total of 55 co-authors. Here are the top co-authors by number of shared publications:
- T. P. Sorokina
Institute of Hydrocarbon Processing, Siberian Branch, Russian Academy of Sciences
16 shared publications - Петр Владимирович Липин
Russian Academy of Sciences
8 shared publications - Oleg V. Potapenko
Center of New Chemical Technologies BIC, Boreskov Institute of Catalysis, Omsk, Russia
7 shared publications - O. V. Potapenko
Institute of Hydrocarbon Processing, Siberian Branch, Russian Academy of Sciences
6 shared publications - Arina Sergeevna Yurtaeva
Center of New Chemical Technologies, Omsk Branch, Federal Research Center Boreskov Institute of Catalysis, Siberian Branch, Russian Academy of Sciences, Omsk, Russia
2 shared publications - N. V. Korotkova
JSC Gazpromneft-Omsk Oil Refinery
2 shared publications
Latest Publications
- 1 September 2024
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 64 (9) , 1106-1112
Catalytic Cracking of n-Dodecane over Alkali-Metal-Modified ZSM-5 Zeolites
The physicochemical properties of ZSM-5 zeolite samples modified with alkali metal cations (e.g., Li+, Na+, K+, and Cs+) were characterized. It was demonstrated that increasing the metal load led to a decrease in the textural properties of the zeolite such as specific surface area, total pore volume, and micropore volume; furthermore, it reduced the total concentration of acid sites by 23–25% (at 0.72 × 10–2 mol % potassium or 0.38 × 10–2 mol % cesium). In the cracking of n-dodecane, the modification of ZSM-5 with 2.34 × 10–2 mol% cesium enhanced the yield of light olefins up to 40.1 wt %, which is comparable with the value achieved by a phosphorus-based ZSM-5 sample (40.3 wt %).
- 1 September 2024
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 64 (9) , 1106-1112
Catalytic Cracking of n-Dodecane over Alkali-Metal-Modified ZSM-5 Zeolites
The physicochemical properties of ZSM-5 zeolite samples modified with alkali metal cations (e.g., Li+, Na+, K+, and Cs+) were characterized. It was demonstrated that increasing the metal load led to a decrease in the textural properties of the zeolite such as specific surface area, total pore volume, and micropore volume; furthermore, it reduced the total concentration of acid sites by 23–25% (at 0.72 × 10–2 mol % potassium or 0.38 × 10–2 mol % cesium). In the cracking of n-dodecane, the modification of ZSM-5 with 2.34 × 10–2 mol% cesium enhanced the yield of light olefins up to 40.1 wt %, which is comparable with the value achieved by a phosphorus-based ZSM-5 sample (40.3 wt %).
- 4 August 2024
- Published by The Russian Academy of Sciences in Neftehimiâ
- Vol. 64 (1) , 5-18
Добавки к катализатору крекинга для снижения содержания токсичных компонентов в дымовых газах (обзор)
Добавки к катализатору крекинга для снижения содержания токсичных компонентов в дымовых газах (обзор) Добавки к катализатору крекинга для снижения содержания токсичных компонентов в дымовых газах (обзор)
- 4 August 2024
- Published by The Russian Academy of Sciences in Neftehimiâ
- Vol. 64 (1) , 5-18
Добавки к катализатору крекинга для снижения содержания токсичных компонентов в дымовых газах (обзор)
Добавки к катализатору крекинга для снижения содержания токсичных компонентов в дымовых газах (обзор) Добавки к катализатору крекинга для снижения содержания токсичных компонентов в дымовых газах (обзор)
- 17 June 2023
- Published by Pleiades Publishing Ltd in Catalysis in Industry
- Vol. 15 (2) , 203-211
Phenol and Tetralin Co-Conversion Regularities under Catalytic Cracking Conditions
The effect of an oxygen-containing compound on the cracking of an aromatic hydrocarbon is studied using the example of a model phenol–tetralin mixture. An analysis of the temperature dependences of the cracking rate constant of tetralin and tetralin in a mixture with phenol indicates that tetralin cracking is ihhibited during its co-conversion with an oxygen-containing compound due to the greater adsorption capacity of phenol on the catalyst’s surface. It is found that phenol in the model mixture changes the composition of liquid products, especially at low cracking temperatures. The effect of water on the conversion of a phenol-tetralin mixture is studied. It is established that water in the model feedstock reduces the inhibition of the cracking reaction of an aromatic hydrocarbon by an oxygen-containing compound. Based on the results of catalytic reactions, it is determined that when water is added, the level of the overall conversion of the mixture and the conversion of tetralin increase regardless of temperature. No appreciable qualitative differences between the distributions of cracking products in model mixtures with and without water have been revealed.
- 17 June 2023
- Published by Pleiades Publishing Ltd in Catalysis in Industry
- Vol. 15 (2) , 203-211
Phenol and Tetralin Co-Conversion Regularities under Catalytic Cracking Conditions
The effect of an oxygen-containing compound on the cracking of an aromatic hydrocarbon is studied using the example of a model phenol–tetralin mixture. An analysis of the temperature dependences of the cracking rate constant of tetralin and tetralin in a mixture with phenol indicates that tetralin cracking is ihhibited during its co-conversion with an oxygen-containing compound due to the greater adsorption capacity of phenol on the catalyst’s surface. It is found that phenol in the model mixture changes the composition of liquid products, especially at low cracking temperatures. The effect of water on the conversion of a phenol-tetralin mixture is studied. It is established that water in the model feedstock reduces the inhibition of the cracking reaction of an aromatic hydrocarbon by an oxygen-containing compound. Based on the results of catalytic reactions, it is determined that when water is added, the level of the overall conversion of the mixture and the conversion of tetralin increase regardless of temperature. No appreciable qualitative differences between the distributions of cracking products in model mixtures with and without water have been revealed.
- 1 January 2023
- Published by Autonomous Non-profit Organization Editorial Board of the journal Uspekhi Khimii in Russian Chemical Reviews
- Vol. 92 (1) , RCR5065
Intermolecular hydrogen transfer reactions as key stages in the catalytic cracking: achievements and outlook
The review summarizes and critically analyzes the results of exploratory and basic studies carried out mainly in the last 10 years concerning the mechanism and role of hydrogen transfer reactions in hydrocarbon conversion processes. A discussion addresses the established views on the regularities of these reactions (mainly involving hydrogen–hydrogen, carbon–carbon and carbon–hydrogen bonds) in various systems containing cations of d-, p - and s-elements. The features of intermolecular hydrogen transfer reactions involved in the zeolite-catalyzed cracking of hydrocarbons are considered. Data on the development of compositions and investigation of properties of modern zeolite-based catalysts for hydrocarbon cracking are discussed. The attention is focused on the role of intermolecular hydrogen transfer in this process, especially in the transformations of heteroatomic compounds. Regarding zeolite compositions, the main attention is paid to the influence of the acid site distribution on the zeolite surface on the hydrogen transfer reactions and the role of extra-framework aluminium species and added modifier cations in these processes. The results of studies of hydrogen transfer by model calculations and by drawing analogies are presented. It is demonstrated that intermolecular hydrogen transfer reactions must be taken into account while addressing problems of improving the cracking catalysts and creating catalytic compositions for joint processing of sulfur, nitrogen and oxygen compounds together with hydrocarbons in the catalytic cracking. The bibliography includes 249 references.
- 1 January 2023
- Published by Autonomous Non-profit Organization Editorial Board of the journal Uspekhi Khimii in Russian Chemical Reviews
- Vol. 92 (1) , RCR5065
Intermolecular hydrogen transfer reactions as key stages in the catalytic cracking: achievements and outlook
The review summarizes and critically analyzes the results of exploratory and basic studies carried out mainly in the last 10 years concerning the mechanism and role of hydrogen transfer reactions in hydrocarbon conversion processes. A discussion addresses the established views on the regularities of these reactions (mainly involving hydrogen–hydrogen, carbon–carbon and carbon–hydrogen bonds) in various systems containing cations of d-, p - and s-elements. The features of intermolecular hydrogen transfer reactions involved in the zeolite-catalyzed cracking of hydrocarbons are considered. Data on the development of compositions and investigation of properties of modern zeolite-based catalysts for hydrocarbon cracking are discussed. The attention is focused on the role of intermolecular hydrogen transfer in this process, especially in the transformations of heteroatomic compounds. Regarding zeolite compositions, the main attention is paid to the influence of the acid site distribution on the zeolite surface on the hydrogen transfer reactions and the role of extra-framework aluminium species and added modifier cations in these processes. The results of studies of hydrogen transfer by model calculations and by drawing analogies are presented. It is demonstrated that intermolecular hydrogen transfer reactions must be taken into account while addressing problems of improving the cracking catalysts and creating catalytic compositions for joint processing of sulfur, nitrogen and oxygen compounds together with hydrocarbons in the catalytic cracking. The bibliography includes 249 references.
- 30 August 2022
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 62 (8) , 886-895
Joint Cracking of Vacuum Gasoil with Vegetable Oils on Zeolite-Containing Catalysts of Various Compositions
The influence of the composition of a zeolite-containing catalyst on the target product distribution in joint cracking of vacuum gasoil with vegetable oils was studied. Introduction of ZSM-5 zeolite into the catalyst formulation favors the formation of light olefins С2–С4: the yield of propylene and butylenes increases. Analysis of the distribution of target cracking products depending on the kind of vegetable oil shows that the maximal yield of С2–С4 olefins is reached when using oils with increased content of saturated fatty acids, especially at high content of ZSM-5 zeolite in the catalyst active component. To ensure the primary cracking of the mixed feedstock, the cracking catalyst matrix should have developed surface and high acid properties.
- 30 August 2022
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 62 (8) , 886-895
Joint Cracking of Vacuum Gasoil with Vegetable Oils on Zeolite-Containing Catalysts of Various Compositions
The influence of the composition of a zeolite-containing catalyst on the target product distribution in joint cracking of vacuum gasoil with vegetable oils was studied. Introduction of ZSM-5 zeolite into the catalyst formulation favors the formation of light olefins С2–С4: the yield of propylene and butylenes increases. Analysis of the distribution of target cracking products depending on the kind of vegetable oil shows that the maximal yield of С2–С4 olefins is reached when using oils with increased content of saturated fatty acids, especially at high content of ZSM-5 zeolite in the catalyst active component. To ensure the primary cracking of the mixed feedstock, the cracking catalyst matrix should have developed surface and high acid properties.
- 29 August 2020
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 60 (8) , 923-928
Coconversion of n-Dodecane and 2-Methylthiophene in the Presence of Dual-Zeolite Cracking Catalysts Containing Different Amounts of Rare-Earth Elements
The effect of the rare-earth element (REE) content in dual-zeolite cracking catalysts on the conversion of n-dodecane and an n-dodecane–2-methylthiophene mixture (5000 ppm S) has been studied. The catalysts have been synthesized using zeolites Y and ZSM-5 modified with REEs and phosphorus, respectively, as the active component. It has been shown that the presence of REE oxides in zeolite Y (at a constant SiO2/Al2O3 ratio) affects the catalytic activity of cracking catalysts based on this zeolite. The dependence of the light olefin yield on the REE oxide content in zeolite Y passes through a maximum at 2–3 wt %. The presence of a sulfur compound in an amount of 5000 ppm (in terms of sulfur) in the feedstock leads to a decrease in the model hydrocarbon conversion and the C2–C4 olefin yield. In the presence of a sulfur compound, the change in the C2–C4 olefin yield as a function of REE oxide content in zeolite Y is less pronounced than that in the case of individual n-dodecane cracking.
- 29 August 2020
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 60 (8) , 923-928
Coconversion of n-Dodecane and 2-Methylthiophene in the Presence of Dual-Zeolite Cracking Catalysts Containing Different Amounts of Rare-Earth Elements
The effect of the rare-earth element (REE) content in dual-zeolite cracking catalysts on the conversion of n-dodecane and an n-dodecane–2-methylthiophene mixture (5000 ppm S) has been studied. The catalysts have been synthesized using zeolites Y and ZSM-5 modified with REEs and phosphorus, respectively, as the active component. It has been shown that the presence of REE oxides in zeolite Y (at a constant SiO2/Al2O3 ratio) affects the catalytic activity of cracking catalysts based on this zeolite. The dependence of the light olefin yield on the REE oxide content in zeolite Y passes through a maximum at 2–3 wt %. The presence of a sulfur compound in an amount of 5000 ppm (in terms of sulfur) in the feedstock leads to a decrease in the model hydrocarbon conversion and the C2–C4 olefin yield. In the presence of a sulfur compound, the change in the C2–C4 olefin yield as a function of REE oxide content in zeolite Y is less pronounced than that in the case of individual n-dodecane cracking.
- 1 March 2019
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 59 (3) , 310-317
The Formation of Properties of Ultrastable Zeolite Y for Cracking and Hydrocracking Catalysts
- 1 March 2019
- Published by Pleiades Publishing Ltd in Petroleum Chemistry
- Vol. 59 (3) , 310-317
The Formation of Properties of Ultrastable Zeolite Y for Cracking and Hydrocracking Catalysts
- Open Access
- 20 November 2018
- Published by Kalvis in Kataliz v promyshlennosti
- Vol. 18 (6) , 48-54
Control of Contribution of Cracking and Intermolecular Hydrogen Transfer in Cracking of Gasoline Fractions in Fixed and Circulating Catalyst Bed Reactors
The studies were focused on the influence of key parameters (temperature, pressure, dilution of the reaction medium with an inert gas) of catalytic processes (cracking of vacuum gasoil, hydrogen-free upgrading and cracking of gasoline fractions) on the ratio of selectivities to cracking and intermolecular hydrogen transfer. Controlling the ratio of these reactions allows the required products to be obtained on the feedstock processing. Lengthening of the feedstock-catalyst contact time, a decrease in the proportion of the diluting inert gas, and the pressure rise provides an increase in the selectivity to hydrogen transfer. Fixed and circulating catalyst bed setups were used for the experiments. Transformations of the feedstock containing deuterated compounds were studied.
- 20 November 2018
- Published by Kalvis in Kataliz v promyshlennosti
- Vol. 18 (6) , 48-54
Open AccessControl of Contribution of Cracking and Intermolecular Hydrogen Transfer in Cracking of Gasoline Fractions in Fixed and Circulating Catalyst Bed Reactors
The studies were focused on the influence of key parameters (temperature, pressure, dilution of the reaction medium with an inert gas) of catalytic processes (cracking of vacuum gasoil, hydrogen-free upgrading and cracking of gasoline fractions) on the ratio of selectivities to cracking and intermolecular hydrogen transfer. Controlling the ratio of these reactions allows the required products to be obtained on the feedstock processing. Lengthening of the feedstock-catalyst contact time, a decrease in the proportion of the diluting inert gas, and the pressure rise provides an increase in the selectivity to hydrogen transfer. Fixed and circulating catalyst bed setups were used for the experiments. Transformations of the feedstock containing deuterated compounds were studied.
- 1 October 2018
- Published by Pleiades Publishing Ltd in Catalysis in Industry
- Vol. 10 (4) , 335-343
Modifying Zeolite ZSM-5 to Increase the Yield of Light Olefins in Cracking Feedstocks of Petroleum and Vegetable Origin
The effect modifying the HZSM-5 zeolite contained in a bizeolite catalyst has on the conversion of hydrotreated vacuum gas oil, vegetable oil, and a vacuum gas oil–vegetable oil mixture under...
- 1 October 2018
- Published by Pleiades Publishing Ltd in Catalysis in Industry
- Vol. 10 (4) , 335-343
Modifying Zeolite ZSM-5 to Increase the Yield of Light Olefins in Cracking Feedstocks of Petroleum and Vegetable Origin
The effect modifying the HZSM-5 zeolite contained in a bizeolite catalyst has on the conversion of hydrotreated vacuum gas oil, vegetable oil, and a vacuum gas oil–vegetable oil mixture under...
- Open Access
- 23 July 2018
- Published by Kalvis in Kataliz v promyshlennosti
- Vol. 18 (4) , 31-40
Modification of ZSM-5 Zeolite in order to Improve the Yield of Light Olefins during Cracking of Oil and Plant Materials
The influence of modifying HZSM-5 zeolite as a component of a bizeolite catalyst in transformations of hydrotreated vacuum gasoil, plant oil, and a mixture of vacuum gasoil and plant oil was studied. The modification with phosphorus was established to decrease the specific surface area and meso- and macropore volumes in HZSM-5 zeolite; the higher phosphorus content, the lower main characteristics of the zeolite porous structure. A decrease in the total acidity of P/HZSM-5 and quantitative redistribution between weak and moderate acid sites also was observed. Testing of the zeolites in catalytic cracking revealed that the phosphorus modification favored an increase in the total yield of propane-propylene and butane-butylene fractions containing olefins in high proportions. Alkali treatment of HZSM-4 zeolite with a high silicate module resulted in a higher silicon extraction and in a considerable increase in the specific surface area of mesopores. In addition, strong acid sites of the zeolite were transformed to weaker ones and/or their exposure changed due to partial silicon removal.
- 23 July 2018
- Published by Kalvis in Kataliz v promyshlennosti
- Vol. 18 (4) , 31-40
Open AccessModification of ZSM-5 Zeolite in order to Improve the Yield of Light Olefins during Cracking of Oil and Plant Materials
The influence of modifying HZSM-5 zeolite as a component of a bizeolite catalyst in transformations of hydrotreated vacuum gasoil, plant oil, and a mixture of vacuum gasoil and plant oil was studied. The modification with phosphorus was established to decrease the specific surface area and meso- and macropore volumes in HZSM-5 zeolite; the higher phosphorus content, the lower main characteristics of the zeolite porous structure. A decrease in the total acidity of P/HZSM-5 and quantitative redistribution between weak and moderate acid sites also was observed. Testing of the zeolites in catalytic cracking revealed that the phosphorus modification favored an increase in the total yield of propane-propylene and butane-butylene fractions containing olefins in high proportions. Alkali treatment of HZSM-4 zeolite with a high silicate module resulted in a higher silicon extraction and in a considerable increase in the specific surface area of mesopores. In addition, strong acid sites of the zeolite were transformed to weaker ones and/or their exposure changed due to partial silicon removal.