Diane M. Moug
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Diane M. Moug has a total of 27 co-authors. Here are the top co-authors by number of shared publications:
- Arash Khosravifar
Assistant Professor, Dept. of Civil and Environmental Engineering, Portland State Univ., Portland, OR 97201. ORCID:
3 shared publications - Jason T. DeJong
University of California
3 shared publications - Edward Kavazanjian
Arizona State University
2 shared publications - Katerina Ziotopoulou
UC Davis
2 shared publications - Maya El Kortbawi
Geotechnical Consultant, Fugro, S51303 Jebel Ali Free Zone (JAFZA) Dubai, United Arab Emirates. ORCID:
2 shared publications - Ross W. Boulanger
Univ. of California, Davis
2 shared publications
Latest Publications
- 27 October 2025
- Published by Springer Nature in Acta Geotechnica
- Vol. 21 (1) , 157-173
Long-term monitoring of a microbially induced desaturation field trial in fine-grained soil
- 27 October 2025
- Published by Springer Nature in Acta Geotechnica
- Vol. 21 (1) , 157-173
Long-term monitoring of a microbially induced desaturation field trial in fine-grained soil
- 1 January 2025
- Published by Portland State University Library
Framework and Methodology for Risk-Based Bridge and Tunnel Asset Management: Risk-Based Asset Ranking and Corridor Prioritization
This report presents the results of Phase II of the project, "Framework and Methodology for Risk-based Bridge and Tunnel Asset Management". The research was carried out at Portland State University in collaboration with engineers and officials at the Oregon Department of Transportation (ODOT) and Federal Highway Administration (FHWA). Using the framework and methodology developed in Phase I of the project, the primary goal of Phase II is to showcase the practical application in risk-based asset management. In particular, the report includes the following two case studies: Case Study I — Weighted hazard scenarios for seismic risk assessment of Oregon Highway Bridges, and Case Study II — Accessibility risk assessment and corridor prioritization for Portland bridge network under a scenario Cascadia Subduction Zone (CSZ) earthquake. Each case study focuses on a specific method proposed in the Phase I of the project.
- 1 January 2025
- Published by Portland State University Library
Framework and Methodology for Risk-Based Bridge and Tunnel Asset Management: Risk-Based Asset Ranking and Corridor Prioritization
This report presents the results of Phase II of the project, "Framework and Methodology for Risk-based Bridge and Tunnel Asset Management". The research was carried out at Portland State University in collaboration with engineers and officials at the Oregon Department of Transportation (ODOT) and Federal Highway Administration (FHWA). Using the framework and methodology developed in Phase I of the project, the primary goal of Phase II is to showcase the practical application in risk-based asset management. In particular, the report includes the following two case studies: Case Study I — Weighted hazard scenarios for seismic risk assessment of Oregon Highway Bridges, and Case Study II — Accessibility risk assessment and corridor prioritization for Portland bridge network under a scenario Cascadia Subduction Zone (CSZ) earthquake. Each case study focuses on a specific method proposed in the Phase I of the project.
- Open Access
- 31 May 2024
- Published by Frontiers Media SA in Frontiers in Built Environment
- Vol. 10, 1386803
Investigation of piezocone dissipation test interpretation in clay accounting for vertical and horizontal porewater pressure dissipation with a large deformation axisymmetric penetration model
The piezocone (CPTu) dissipation test is used to characterize how the applied load from the penetrating cone is distributed between the soil and pore fluid during both penetrometer advancement and when penetration is paused. The coefficient of consolidation is often estimated from CPTu dissipation tests by interpreting the rate of excess porewater pressure () decay to static conditions during a pause in cone penetration. Most CPTu dissipation test interpretation methods are based on Terzaghi consolidation theory for dissipation at the cone shoulder ( position) or cone face ( position) and assume that radial dissipation dominates the response. However, several recent studies show that vertical migration does contribute to the response. This study uses a large deformation direct axisymmetric cone penetration model to characterize the soil-water mechanical response during CPTu dissipation tests, and in particular, the role of vertical dissipation on the response at the and positions. Large deformations around the penetrating cone are accommodated with an Arbitrary Lagrangian Eulerian approach. Soil behavior is modeled with the MIT-S1 constitutive model calibrated for Boston blue clay (BBC) soil behavior. dissipation following undrained cone penetration is simulated with coupled consolidation for BBC with over-consolidation ratios (OCR) of 1, 2, and 4 and a range of hydraulic conductivity anisotropy. The simulated and dissipation responses are presented to study how they are affected by OCR and hydraulic conductivity anisotropy. A correction factor is recommended to account for hydraulic conductivity anisotropy when interpreting the horizontal coefficient of consolidation from CPTu dissipation tests.- 31 May 2024
- Published by Frontiers Media SA in Frontiers in Built Environment
- Vol. 10, 1386803
Open AccessInvestigation of piezocone dissipation test interpretation in clay accounting for vertical and horizontal porewater pressure dissipation with a large deformation axisymmetric penetration model
The piezocone (CPTu) dissipation test is used to characterize how the applied load from the penetrating cone is distributed between the soil and pore fluid during both penetrometer advancement and when penetration is paused. The coefficient of consolidation is often estimated from CPTu dissipation tests by interpreting the rate of excess porewater pressure () decay to static conditions during a pause in cone penetration. Most CPTu dissipation test interpretation methods are based on Terzaghi consolidation theory for dissipation at the cone shoulder ( position) or cone face ( position) and assume that radial dissipation dominates the response. However, several recent studies show that vertical migration does contribute to the response. This study uses a large deformation direct axisymmetric cone penetration model to characterize the soil-water mechanical response during CPTu dissipation tests, and in particular, the role of vertical dissipation on the response at the and positions. Large deformations around the penetrating cone are accommodated with an Arbitrary Lagrangian Eulerian approach. Soil behavior is modeled with the MIT-S1 constitutive model calibrated for Boston blue clay (BBC) soil behavior. dissipation following undrained cone penetration is simulated with coupled consolidation for BBC with over-consolidation ratios (OCR) of 1, 2, and 4 and a range of hydraulic conductivity anisotropy. The simulated and dissipation responses are presented to study how they are affected by OCR and hydraulic conductivity anisotropy. A correction factor is recommended to account for hydraulic conductivity anisotropy when interpreting the horizontal coefficient of consolidation from CPTu dissipation tests. - 1 November 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 149 (11)
Closure to “Axisymmetric Simulations of Cone Penetration in Biocemented Sands”
- 1 November 2023
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 149 (11)
Closure to “Axisymmetric Simulations of Cone Penetration in Biocemented Sands”
- 1 November 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (11) , 04022098
Axisymmetric Simulations of Cone Penetration in Biocemented Sands
With the recent advances in the biogeotechnics field and specifically microbially induced calcite precipitation (MICP), cone penetration testing (CPT) has become a valuable tool to overcome the challenges associated with intact sampling of improved soils, evaluate the spatial extent and magnitude of the applied MICP treatment, and assess the consequential improvement of engineering properties. Although the CPT cone tip resistance ( ) can effectively monitor the improvement of densified clean sands, no relationship exists to estimate cementation and strength parameters in MICP-treated sands. This paper proposes a relationship between the apparent cohesion ( ) stemming from the MICP-induced cementation bonds at particle contacts and the change in tip resistance in initially loose sands. To develop a broadly useful correlation, available experimental CPT data in biocemented soils were used to guide computation simulations using a direct axisymmetric model of cone penetration in biocemented sands. The CPT numerical model uses the finite-difference method with a rezoning algorithm for large-deformation problems along with the Mohr-Coulomb constitutive model. The biocemented sand was characterized by Mohr-Coulomb strength parameters and an elastic shear modulus informed by shear-wave velocity measurements ( ). The correlation parameters of interest were identified ( , , and ), and results of the numerical simulations were validated against available experimental data. Once validated, the numerical simulations were extended to different initial conditions, and the trends between parameters of interest were analyzed and interpreted. Results from the simulations are consistent with experimental data and show an increase in the cone tip resistance as the cementation level increases. The cementation level is modeled through apparent cohesion and the shear stiffness model parameters, which both increase as the cementation level increases. A linear relationship is proposed between the apparent cohesion and the change in cone tip resistance as a function of the confining stress.- 1 November 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (11) , 04022098
Axisymmetric Simulations of Cone Penetration in Biocemented Sands
With the recent advances in the biogeotechnics field and specifically microbially induced calcite precipitation (MICP), cone penetration testing (CPT) has become a valuable tool to overcome the challenges associated with intact sampling of improved soils, evaluate the spatial extent and magnitude of the applied MICP treatment, and assess the consequential improvement of engineering properties. Although the CPT cone tip resistance ( ) can effectively monitor the improvement of densified clean sands, no relationship exists to estimate cementation and strength parameters in MICP-treated sands. This paper proposes a relationship between the apparent cohesion ( ) stemming from the MICP-induced cementation bonds at particle contacts and the change in tip resistance in initially loose sands. To develop a broadly useful correlation, available experimental CPT data in biocemented soils were used to guide computation simulations using a direct axisymmetric model of cone penetration in biocemented sands. The CPT numerical model uses the finite-difference method with a rezoning algorithm for large-deformation problems along with the Mohr-Coulomb constitutive model. The biocemented sand was characterized by Mohr-Coulomb strength parameters and an elastic shear modulus informed by shear-wave velocity measurements ( ). The correlation parameters of interest were identified ( , , and ), and results of the numerical simulations were validated against available experimental data. Once validated, the numerical simulations were extended to different initial conditions, and the trends between parameters of interest were analyzed and interpreted. Results from the simulations are consistent with experimental data and show an increase in the cone tip resistance as the cementation level increases. The cementation level is modeled through apparent cohesion and the shear stiffness model parameters, which both increase as the cementation level increases. A linear relationship is proposed between the apparent cohesion and the change in cone tip resistance as a function of the confining stress.- 1 November 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (11) , 05022005
Field Trials of Microbially Induced Desaturation in Low-Plasticity Silt
Field trials of microbially induced desaturation (MID) were conducted at two sites in Portland, Oregon underlain by liquefiable fine-grained soils. MID is an emerging method for mitigating the potential for triggering liquefaction. MID treatment stimulates native denitrifying microbes with a solution containing nitrate, as well as other substrates and nutrients. An end product of the denitrification reactions is nitrogen gas, which displaces soil porewater and in turn reduces the in situ degree of saturation ( ). Because during cyclic loading desaturated soils produce less excess porewater pressure than saturated soils, MID can mitigate the potential for triggering liquefaction. Monitoring for the two field trials was performed to evaluate the MID treatment performance and the associated subsurface desaturation. Monitoring data included seismic wave velocities measured with crosshole and downhole techniques, embedded in situ moisture and electrical conductivity sensors, water chemistry measurements, and recovery and testing of samples for changes in soil properties. Monitoring data were collected pretreatment, during treatment, and post-treatment, and then interpreted to evaluate the effectiveness of MID for reducing in fine grained, low plasticity silts in the two distinct sites. Despite geotechnical site characterization data that show the field trial sites have distinct geotechnical characteristics, including interbedding, that affect liquefaction susceptibility and MID treatment application, results indicate liquefiable soil at both sites was successfully desaturated and that the desaturation persisted for at least 92 days post-treatment.- 1 November 2022
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 148 (11) , 05022005
Field Trials of Microbially Induced Desaturation in Low-Plasticity Silt
Field trials of microbially induced desaturation (MID) were conducted at two sites in Portland, Oregon underlain by liquefiable fine-grained soils. MID is an emerging method for mitigating the potential for triggering liquefaction. MID treatment stimulates native denitrifying microbes with a solution containing nitrate, as well as other substrates and nutrients. An end product of the denitrification reactions is nitrogen gas, which displaces soil porewater and in turn reduces the in situ degree of saturation ( ). Because during cyclic loading desaturated soils produce less excess porewater pressure than saturated soils, MID can mitigate the potential for triggering liquefaction. Monitoring for the two field trials was performed to evaluate the MID treatment performance and the associated subsurface desaturation. Monitoring data included seismic wave velocities measured with crosshole and downhole techniques, embedded in situ moisture and electrical conductivity sensors, water chemistry measurements, and recovery and testing of samples for changes in soil properties. Monitoring data were collected pretreatment, during treatment, and post-treatment, and then interpreted to evaluate the effectiveness of MID for reducing in fine grained, low plasticity silts in the two distinct sites. Despite geotechnical site characterization data that show the field trial sites have distinct geotechnical characteristics, including interbedding, that affect liquefaction susceptibility and MID treatment application, results indicate liquefiable soil at both sites was successfully desaturated and that the desaturation persisted for at least 92 days post-treatment.- 20 September 2022
- Published by Springer Nature
- p. 961-970
Ground Deformation Evaluation Using Numerical Analyses and Physics-Based Mega-thrust Subduction Zone Motions
- 20 September 2022
- Published by Springer Nature
- p. 961-970
Ground Deformation Evaluation Using Numerical Analyses and Physics-Based Mega-thrust Subduction Zone Motions
- 1 April 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 145 (4)
Axisymmetric Simulations of Cone Penetration in Saturated Clay
A direct axisymmetric cone-penetration model developed for use with a user-written implementation of the MIT-S1 constitutive model is presented. The penetration model uses a finite-difference program with an Arbitrary Lagrangian Eulerian algorithm that couples the program’s large-deformation Lagrangian formulation with user-written algorithms for rezoning and second-order Eulerian advection remapping. Numerical examples illustrate the performance of the remapping and advection algorithms and cone-penetration simulations. Cone penetration at a Boston blue clay site is simulated with the Mohr-Coulomb, modified Cam clay, and MIT-S1 constitutive models and compared with measured cone-penetration test profiles. Single-element simulations illustrate that the MIT-S1 constitutive model captures the significant undrained shear-strength anisotropy exhibited by Boston blue clay, whereas the modified Cam clay and Mohr-Coulomb models do not. Penetration simulations demonstrate the important effect of undrained shear-strength anisotropy on the cone tip resistance, as well as on stress and pore pressure fields around the cone tip and rod.
- 1 April 2019
- Published by American Society of Civil Engineers (ASCE) in Journal of Geotechnical and Geoenvironmental Engineering
- Vol. 145 (4)
Axisymmetric Simulations of Cone Penetration in Saturated Clay
A direct axisymmetric cone-penetration model developed for use with a user-written implementation of the MIT-S1 constitutive model is presented. The penetration model uses a finite-difference program with an Arbitrary Lagrangian Eulerian algorithm that couples the program’s large-deformation Lagrangian formulation with user-written algorithms for rezoning and second-order Eulerian advection remapping. Numerical examples illustrate the performance of the remapping and advection algorithms and cone-penetration simulations. Cone penetration at a Boston blue clay site is simulated with the Mohr-Coulomb, modified Cam clay, and MIT-S1 constitutive models and compared with measured cone-penetration test profiles. Single-element simulations illustrate that the MIT-S1 constitutive model captures the significant undrained shear-strength anisotropy exhibited by Boston blue clay, whereas the modified Cam clay and Mohr-Coulomb models do not. Penetration simulations demonstrate the important effect of undrained shear-strength anisotropy on the cone tip resistance, as well as on stress and pore pressure fields around the cone tip and rod.