Irma Lucía Vera-Estrada
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Irma Lucía Vera-Estrada has a total of 19 co-authors. Here are the top co-authors by number of shared publications:
- Juan Manuel Olivares-Ramírez
Universidad Tecnológica de San Juan del Río
4 shared publications - Andres Dector
SECIHTI—Department Renewable Energy, Universidad Tecnológica de San Juan del Río, San Juan del Río 76800, Querétaro, Mexico
3 shared publications - Juvenal Rodríguez-Reséndiz
Facultad de Ingeniería, Universidad Autónoma de Querétaro, Querétaro 76010, Mexico
3 shared publications - Iveth Dalila Antonio-Carmona
Departamento de Botánica, Universidad Autónoma Agraria Antonio Narro, Saltillo, Mexico
2 shared publications - José Eli Eduardo González-Durán
Escuela Nacional de Estudios Superiores Unidad Juriquilla, Universidad Nacional Autónoma de México, Querétaro C.P. 76230, Querétaro, Mexico
2 shared publications - Victor Manuel Ovando-Medina
Ingeniería Química, Unidad Académica Multidisciplinaria Región Altiplano (UAMRA), Universidad Autónoma de San Luis Potosí, Matehuala, México
2 shared publications
Latest Publications
- Open Access
Air-Breathing Microfluidic Fuel Cell Stack Powered by Tequila: Experimental Evaluation and Computational Fluid Dynamics Simulation of Series-Parallel Configurations Effect
Microfluidic fuel cells offer a promising route for portable power generation; however, scaling paper-based systems remains challenging because capillary-driven flow can limit fuel distribution and electrochemical performance. This work investigates the experimental performance and computational fluid dynamics (CFD) behavior of air-breathing paper-based microfluidic fuel cell (FCs) stacks powered directly by commercial tequila (35 vol.% ethanol). Single cells with electrode areas ranging from 0.5 cm × 0.5 cm to 3 cm × 3 cm were evaluated to determine the optimal design, followed by the construction of 4-cell and 6-cell series-parallel stacks. The smallest electrode (0.5 cm × 0.5 cm) achieved the highest power density (0.142 mW cm−2) and open-circuit voltage (0.92 V). Scaling to a 6-cell stack increased the maximum power density to 3.20 mW cm−2 and the voltage to 1.39 V, outperforming the 4-cell configuration (1.09 mW cm−2 and 1.07 V). Computational Fluid Dynamics simulations revealed that fuel velocity decreased from 2.8 × 10−2 m s−1 near the inlet to approximately 1.0 × 10−6 m s−1 in the final cells because of porous-medium resistance, explaining the observed mass-transport limitations. The results demonstrate that tequila can be directly used as a sustainable fuel source and that optimized stack architectures significantly enhance power generation in paper-based microfluidic fuel cells.Open AccessAir-Breathing Microfluidic Fuel Cell Stack Powered by Tequila: Experimental Evaluation and Computational Fluid Dynamics Simulation of Series-Parallel Configurations Effect
Microfluidic fuel cells offer a promising route for portable power generation; however, scaling paper-based systems remains challenging because capillary-driven flow can limit fuel distribution and electrochemical performance. This work investigates the experimental performance and computational fluid dynamics (CFD) behavior of air-breathing paper-based microfluidic fuel cell (FCs) stacks powered directly by commercial tequila (35 vol.% ethanol). Single cells with electrode areas ranging from 0.5 cm × 0.5 cm to 3 cm × 3 cm were evaluated to determine the optimal design, followed by the construction of 4-cell and 6-cell series-parallel stacks. The smallest electrode (0.5 cm × 0.5 cm) achieved the highest power density (0.142 mW cm−2) and open-circuit voltage (0.92 V). Scaling to a 6-cell stack increased the maximum power density to 3.20 mW cm−2 and the voltage to 1.39 V, outperforming the 4-cell configuration (1.09 mW cm−2 and 1.07 V). Computational Fluid Dynamics simulations revealed that fuel velocity decreased from 2.8 × 10−2 m s−1 near the inlet to approximately 1.0 × 10−6 m s−1 in the final cells because of porous-medium resistance, explaining the observed mass-transport limitations. The results demonstrate that tequila can be directly used as a sustainable fuel source and that optimized stack architectures significantly enhance power generation in paper-based microfluidic fuel cells. - 1 November 2024
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 16 (6)
Power generation using diabetic urine as fuel in a paper-based microfluidic fuel cell with a ZnO/Ni-based composite anode
This work presents, for the first time, power generation using diabetic urine as fuel. The energy conversion is achieved through a paper-based microfluidic fuel cell. Urine has recently gained attention as a source of novel biomarkers for early disease detection, making the use of diabetic urine as fuel particularly relevant to the development of autonomous portable medical devices. A key challenge in using diabetic urine as fuel lies in the fact that it contains various molecules and compounds that can block or poison the fuel cell's electrodes. This study introduces a selective catalyst of ZnO and nickel-based particles that oxidize the urea in human urine. Different concentrations of Ni (3%, 6%, and 9%) were evaluated to optimize catalyst activity. The best performance of the diabetic urine-microfluidic fuel cell was achieved with the ZnO-Ni at 3%, yielding a maximum voltage of 0.89 V, a maximum current density of 1.18 mA cm−2, and a maximum power density of 1.26 mW cm−2. These results demonstrate the potential for enhancing point-of-care devices through paper-based microfluidic fuel cell stacks.
- 1 November 2024
- Published by AIP Publishing in Journal of Renewable and Sustainable Energy
- Vol. 16 (6)
Power generation using diabetic urine as fuel in a paper-based microfluidic fuel cell with a ZnO/Ni-based composite anode
This work presents, for the first time, power generation using diabetic urine as fuel. The energy conversion is achieved through a paper-based microfluidic fuel cell. Urine has recently gained attention as a source of novel biomarkers for early disease detection, making the use of diabetic urine as fuel particularly relevant to the development of autonomous portable medical devices. A key challenge in using diabetic urine as fuel lies in the fact that it contains various molecules and compounds that can block or poison the fuel cell's electrodes. This study introduces a selective catalyst of ZnO and nickel-based particles that oxidize the urea in human urine. Different concentrations of Ni (3%, 6%, and 9%) were evaluated to optimize catalyst activity. The best performance of the diabetic urine-microfluidic fuel cell was achieved with the ZnO-Ni at 3%, yielding a maximum voltage of 0.89 V, a maximum current density of 1.18 mA cm−2, and a maximum power density of 1.26 mW cm−2. These results demonstrate the potential for enhancing point-of-care devices through paper-based microfluidic fuel cell stacks.
- Open Access
Bio-Power Generation in Microbial Fuel Cell with Vermicompost Using Eisenia foetida
This research emphasizes the effect of using Eisenia foetida in vermicompost for power generation in microbial fuel cells (MFCs). By accelerating the organic decomposition, the bioenergy generation is improved. A vermicompost-microbial fuel cell employing electrogenic microorganisms was used to convert chemical energy into electrical energy. In this work, substrates of black soil, tree bark, leaves, eggshells, and ground tomatoes were used. The vermicompost MFC has a copper cathode and a stainless steel anode. In this study, the performance of MFCs was evaluated using different numbers of Eisenia foetida specimens, with three specimens (MFCW3), five specimens (MFCW5), and seven specimens (MFCW7). Our key findings show that by increasing the number of Eisenia foetida specimens does not bring higher power densities; as a result, the best power density was observed in MFCW3 and MFCW5 at the end of the fourth week, both presenting a total of five Eisenia foetida specimens with a power density of 192 mW m−2. Therefore, optimal results were found when 330 g of substrate and five Eisenia foetida specimens were used to achieve a maximum current density of 900 mW m−2 and a maximum power density of 192 mW m−2. This type of microbial fuel cell can be considered as an alternative for power generation with a significantly reduced environmental impact, considering the use of organic waste. It can be considered a game-changer in waste management and bioenergy projects.
Open AccessBio-Power Generation in Microbial Fuel Cell with Vermicompost Using Eisenia foetida
This research emphasizes the effect of using Eisenia foetida in vermicompost for power generation in microbial fuel cells (MFCs). By accelerating the organic decomposition, the bioenergy generation is improved. A vermicompost-microbial fuel cell employing electrogenic microorganisms was used to convert chemical energy into electrical energy. In this work, substrates of black soil, tree bark, leaves, eggshells, and ground tomatoes were used. The vermicompost MFC has a copper cathode and a stainless steel anode. In this study, the performance of MFCs was evaluated using different numbers of Eisenia foetida specimens, with three specimens (MFCW3), five specimens (MFCW5), and seven specimens (MFCW7). Our key findings show that by increasing the number of Eisenia foetida specimens does not bring higher power densities; as a result, the best power density was observed in MFCW3 and MFCW5 at the end of the fourth week, both presenting a total of five Eisenia foetida specimens with a power density of 192 mW m−2. Therefore, optimal results were found when 330 g of substrate and five Eisenia foetida specimens were used to achieve a maximum current density of 900 mW m−2 and a maximum power density of 192 mW m−2. This type of microbial fuel cell can be considered as an alternative for power generation with a significantly reduced environmental impact, considering the use of organic waste. It can be considered a game-changer in waste management and bioenergy projects.
- Open Access
Digital Pregnancy Test Powered by an Air-Breathing Paper-Based Microfluidic Fuel Cell Stack Using Human Urine as Fuel
The direct integration of paper-based microfluidic fuel cells (μFC’s) toward creating autonomous lateral flow assays has attracted attention. Here, we show that an air-breathing paper-based μFC could be used as a power supply in pregnancy tests by oxidizing the human urine used for the diagnosis. We present an air-breathing paper-based μFC connected to a pregnancy test, and for the first time, as far as we know, it is powered by human urine without needing any external electrolyte. It uses TiO-Ni as anode and Pt/C as cathode; the performance shows a maximum value of voltage and current and power densities of ∼0.96 V, 1.00 mA cm, and 0.23 mW cm, respectively. Furthermore, we present a simple design of a paper-based μFC’s stack powered with urine that shows a maximum voltage and maximum current and power densities of ∼1.89 V, 2.77 mA cm and 1.38 mW cm, respectively, which powers the display of a pregnancy test allowing to see the analysis results.Open AccessDigital Pregnancy Test Powered by an Air-Breathing Paper-Based Microfluidic Fuel Cell Stack Using Human Urine as Fuel
The direct integration of paper-based microfluidic fuel cells (μFC’s) toward creating autonomous lateral flow assays has attracted attention. Here, we show that an air-breathing paper-based μFC could be used as a power supply in pregnancy tests by oxidizing the human urine used for the diagnosis. We present an air-breathing paper-based μFC connected to a pregnancy test, and for the first time, as far as we know, it is powered by human urine without needing any external electrolyte. It uses TiO-Ni as anode and Pt/C as cathode; the performance shows a maximum value of voltage and current and power densities of ∼0.96 V, 1.00 mA cm, and 0.23 mW cm, respectively. Furthermore, we present a simple design of a paper-based μFC’s stack powered with urine that shows a maximum voltage and maximum current and power densities of ∼1.89 V, 2.77 mA cm and 1.38 mW cm, respectively, which powers the display of a pregnancy test allowing to see the analysis results.