Lei Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Research Interests
Lei Li has a total of 11 co-authors. Here are the top co-authors by number of shared publications:
- Chenying Wang
School of Instrument Science and Technology, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Dan Xian
Collaborative Innovation Center of High-End Manufacturing, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Duanzhi Duan
School of Mechanical Engineering, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication - Ming Liu
Xi’an Jiaotong University
1 shared publication - Qi Mao
School of Instrument Science and Technology, International Joint Laboratory for Micro/Nano Manufacturing and Measurement Technology, Xi'an Jiaotong University Suzhou Institute, Xi'an Jiaotong University 2 , Xi'an 710049
1 shared publication - Qijing Lin
State Key Laboratory for Manufacturing Systems Engineering, Xi’an Jiaotong University, Xi’an 710049, China
1 shared publication
Latest Publications
- Open Access
- 2 September 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (9) , 1454
A Study on the Sub-5 nm Nano-Step Height Reference Materials Fabricated by Atomic Layer Deposition Combined with Wet Etching
Nano-steps, as classical nano-geometric reference materials, are very important for calibrating measurements in the semiconductor industry; therefore, controlling the height of nano-steps is critical for ensuring accurate measurements. Accordingly, in this study nano-steps with heights of 1, 2, 3 and 4 nm were fabricated with good morphology using atomic layer deposition (ALD) combined with wet etching. The roughness of the fabricated nano-steps was effectively controlled by utilizing the three-dimensional conformal ALD process. Moreover, the relationship between the surface roughness and the height was studied using a simulation-based analysis. Essentially, roughness control is crucial in fabricating nano-steps with a critical dimension of less than 5 nm. In this study, the minimum height of a nano-step that was successfully achieved by combining ALD and wet etching was 1 nm. Furthermore, the preconditions for quality assurance for a reference material and the influencing factors of the fabrication method were analyzed based on the 1 nm nano-step sample. Finally, the fabricated samples were used in time-dependent experiments to verify the optimal stability of the nano-steps as reference materials. This research is instructive to fabricate nano-geometric reference materials to within 5 nm in height, and the proposed method can be easily employed to manufacture wafer-sized step height reference materials, thus enabling its large-scale industrial application for in-line calibration in integrated circuit production lines.
- 2 September 2022
- Published by MDPI AG in Micromachines
- Vol. 13 (9) , 1454
Open AccessA Study on the Sub-5 nm Nano-Step Height Reference Materials Fabricated by Atomic Layer Deposition Combined with Wet Etching
Nano-steps, as classical nano-geometric reference materials, are very important for calibrating measurements in the semiconductor industry; therefore, controlling the height of nano-steps is critical for ensuring accurate measurements. Accordingly, in this study nano-steps with heights of 1, 2, 3 and 4 nm were fabricated with good morphology using atomic layer deposition (ALD) combined with wet etching. The roughness of the fabricated nano-steps was effectively controlled by utilizing the three-dimensional conformal ALD process. Moreover, the relationship between the surface roughness and the height was studied using a simulation-based analysis. Essentially, roughness control is crucial in fabricating nano-steps with a critical dimension of less than 5 nm. In this study, the minimum height of a nano-step that was successfully achieved by combining ALD and wet etching was 1 nm. Furthermore, the preconditions for quality assurance for a reference material and the influencing factors of the fabrication method were analyzed based on the 1 nm nano-step sample. Finally, the fabricated samples were used in time-dependent experiments to verify the optimal stability of the nano-steps as reference materials. This research is instructive to fabricate nano-geometric reference materials to within 5 nm in height, and the proposed method can be easily employed to manufacture wafer-sized step height reference materials, thus enabling its large-scale industrial application for in-line calibration in integrated circuit production lines.