Emma Pearce
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Research Interests
Emma Pearce has a total of 90 co-authors. Here are the top co-authors by number of shared publications:
- Dimitri Zigone
Université de Strasbourg/CNRS, Institut Terre et Environnement de Strasbourg, UMR7063, Strasbourg, France
14 shared publications - Olaf Eisen
Alfred Wegener Institute, Bremerhaven, Germany
14 shared publications Coen Hofstede
Alfred Wegener Institute Helmholtz Centre for Polar and Marine Research, Bremerhaven, Germany
13 shared publications- Andreas Fichtner
Department of Earth and Planetary Sciences, ETH Zurich , 8092 Zurich
8 shared publications - Elizabeth Ruth Thomas
British Antarctic Survey Cambridge UK
8 shared publications - Oliver J. Marsh
British Antarctic Survey, Cambridge, CB3 0ET, United Kingdom
8 shared publications
Latest Publications
- Open Access
- 7 September 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-12
Reply on RC2
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- 7 September 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-12
Open AccessReply on RC2
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- Open Access
- 7 September 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-12
Reply on RC1
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- 7 September 2026
- Published by Copernicus GmbH
- Vol. 2026, 1-12
Open AccessReply on RC1
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- Open Access
- 2 September 2026
- Published by Copernicus GmbH
- p. 1-12
Comment on egusphere-2026-3762
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- 2 September 2026
- Published by Copernicus GmbH
- p. 1-12
Open AccessComment on egusphere-2026-3762
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- Open Access
- 21 July 2026
- Published by Copernicus GmbH
- p. 1-12
Comment on egusphere-2026-3762
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- 21 July 2026
- Published by Copernicus GmbH
- p. 1-12
Open AccessComment on egusphere-2026-3762
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- Open Access
- 2 July 2026
- Published by Copernicus GmbH in EGUsphere
Ice-core break-off as an opportunistic seismic source on the Northeast Greenland Ice Stream
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- 2 July 2026
- Published by Copernicus GmbH in EGUsphere
Open AccessIce-core break-off as an opportunistic seismic source on the Northeast Greenland Ice Stream
Ice-core drilling generates repeated mechanical disturbances within the ice column, raising the possibility that operational drilling signals could be used as opportunistic seismic sources. We test whether impulsive ice-core break-off events during the 2022 EastGRIP (Greenland) field season can be detected on surface-based, near-offset three-component geophones and used to estimate apparent P-wave velocity. A catalogue of 67 candidate core-break times was identified from drill-log load peaks, of which 37 had sufficient simultaneous near-offset seismic station coverage for assessment. Only three of these assessable events produced plausible impulsive arrivals. Automatic STA/LTA triggering was useful for identifying candidate windows, but did not reliably pick first arrivals. Where clear arrivals were identifiable above the background noise, manually picked arrivals gave apparent P-wave velocities consistent with firn/ice propagation, and showed a small across-flow faster-than-along-flow tendency, though this difference remains below the level of uncertainty required for robust anisotropy interpretation. These results show that ice-core break-off may provide a useful opportunistic seismic source, but only if future deployments include direct source-time measurement, quiet acquisition conditions, and receiver geometries designed for this purpose.
- Open Access
- 12 May 2026
- Published by Copernicus GmbH in The Cryosphere
- Vol. 20 (5) , 2723-2734
Impact of surface melt and brine infiltration on fracture toughness of ice shelves
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/2024 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼37 m depth and line scans indicate that the upper 37 m contain ∼7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.
- 12 May 2026
- Published by Copernicus GmbH in The Cryosphere
- Vol. 20 (5) , 2723-2734
Open AccessImpact of surface melt and brine infiltration on fracture toughness of ice shelves
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/2024 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼37 m depth and line scans indicate that the upper 37 m contain ∼7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.
- Open Access
- 23 February 2026
- Published by Copernicus GmbH
- Vol. 2025, 1-19
Reply on RC2
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/24 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼ 37 m depth and line scans indicate that the upper 37 m contain ∼ 7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼ 40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.
- 23 February 2026
- Published by Copernicus GmbH
- Vol. 2025, 1-19
Open AccessReply on RC2
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/24 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼ 37 m depth and line scans indicate that the upper 37 m contain ∼ 7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼ 40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.
- Open Access
- 22 February 2026
- Published by Copernicus GmbH
- Vol. 2025, 1-19
Reply on RC1
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/24 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼ 37 m depth and line scans indicate that the upper 37 m contain ∼ 7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼ 40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.
- 22 February 2026
- Published by Copernicus GmbH
- Vol. 2025, 1-19
Open AccessReply on RC1
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/24 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼ 37 m depth and line scans indicate that the upper 37 m contain ∼ 7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼ 40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.
- Open Access
- 2 December 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-19
Comment on egusphere-2025-4904
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/24 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼ 37 m depth and line scans indicate that the upper 37 m contain ∼ 7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼ 40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.
- 2 December 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-19
Open AccessComment on egusphere-2025-4904
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/24 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼ 37 m depth and line scans indicate that the upper 37 m contain ∼ 7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼ 40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.
- Open Access
- 6 November 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-19
Amendment to Affiliation and Acknowledgements
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/24 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼ 37 m depth and line scans indicate that the upper 37 m contain ∼ 7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼ 40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.
- 6 November 2025
- Published by Copernicus GmbH
- Vol. 2025, 1-19
Open AccessAmendment to Affiliation and Acknowledgements
Ice shelves are heterogeneous composites of firn, meteoric ice, refrozen melt and brine-saturated ice. The properties and distribution of these elements control ice shelf response to stress and susceptibility to fracturing. Here, we quantify how surface-melt and brine infiltration modify the Mode I fracture toughness (KIc) of meteoric ice on the Brunt Ice Shelf (BIS), Antarctica. During the 2023/24 austral summer, we recovered a 37 m core sequence from meteoric infill ice near Halley VI, where radar mapping shows continuous brine horizons at ∼ 37 m depth and line scans indicate that the upper 37 m contain ∼ 7 % refrozen melt. We combined density, salinity, temperature and grain size measurements with semi-circular three-point bending tests on samples representing (i) meteoric ice, (ii) melt-modified meteoric ice, and (iii) brine-infiltrated meteoric ice. Our results show melt-modified samples are consistently tougher than melt-free meteoric ice, with KIc increases up to ∼ 40 %. This is despite their larger grain size, indicating densification dominates over grain-size effects. In contrast, brine-saturated meteoric ice exhibits markedly lower KIc, by 14 %–34 % relative to density-matched, brine-free meteoric ice, consistent with chemical weakening and lower freezing temperatures. Our results demonstrate that as KIc varies strongly with density, salinity and depth, a spatially and temporally constant toughness value is unlikely to reproduce calving behaviour accurately. Implementing spatially and vertically variable KIc values, and understanding how ice shelf structure and composition evolves over time, is essential to improve predictions of rift propagation and calving.