Nusrat Jahan Mim
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Nusrat Jahan Mim has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Faiz Uddin Ahmed Shaikh
School of Civil and Mechanical Engineering, Curtin University
4 shared publications - Mizan Ahmed
Centre for Infrastructure Monitoring and Protection, School of Civil and Mechanical Engineering, Curtin University, Bentley, Australia
4 shared publications - Montaseer Meraz
Department of Building Engineering and Construction Management, Khulna University of Engineering and Technology, Khulna 9203, Bangladesh
4 shared publications - Shuvo Dip Datta
Department of Building Engineering and Construction Management, Khulna University of Engineering & Technology, Khulna, Bangladesh
3 shared publications - Ehsan Noroozinejad Farsangi
Western Sydney Univ
2 shared publications Habibur Rahman Sobuz
2 shared publications
Latest Publications
- Open Access
Basaltic Rock Dust as a Sustainable Supplementary Cementitious Material for 3D-Printed Concrete: From Mix Optimisation to Printing Performance
The growing demand for sustainable binder systems in 3D-printed concrete (3DPC), together with the declining availability of fly ash (FA), has increased the need for alternative supplementary cementitious materials. This study investigates the feasibility of using basaltic rock dust (BRD) as a high-volume replacement of FA in 3DPC through a two-stage experimental programme involving mix optimisation followed by evaluation under printing conditions. Five mortar mixes incorporating BRD at FA replacement levels of 0%, 25%, 50%, 75%, and 100% by mass were first evaluated to identify the optimum replacement level within the investigated range, after which the optimum mix was comprehensively characterised in terms of its fresh properties, rheological behaviour, hydration characteristics, mechanical performance, anisotropy, and microstructure. The results showed that 75% FA replacement by BRD achieved the optimum overall performance among the investigated BRD-containing mixes, based on the combined consideration of high BRD utilisation, flowability, hydration behaviour, and compressive strength. Although its 28-day compressive strength under conventionally cast conditions remained slightly lower than that of the control mix, under printing conditions, the C75 mix increased the flow diameter from 165 mm to 176 mm and the maximum printable layers from 14 to 16 while reducing the shape retention spread diameter from 96 mm to 89 mm. Compared with the control mix, the BRD-incorporated mix also increased the compressive strength by 10.9% in the Y- direction and 22.9% in the Z-direction, respectively, while reducing the compressive anisotropy from 20.97% to 12.39%. Although the flexural strength decreased from 7.66 to 5.02 MPa in the Y-direction and from 7.29 to 5.19 MPa in the Z-direction, the directional dependence decreased from 4.83% to 3.34%. SEM observations revealed a more compact cementitious matrix with fewer visible large pores in C75 than in the control mix. These findings demonstrate that BRD has strong potential as a high-volume replacement for FA in 3D-printed concrete, reducing reliance on fly ash while achieving favourable printability, compressive performance, and structural uniformity.
Open AccessBasaltic Rock Dust as a Sustainable Supplementary Cementitious Material for 3D-Printed Concrete: From Mix Optimisation to Printing Performance
The growing demand for sustainable binder systems in 3D-printed concrete (3DPC), together with the declining availability of fly ash (FA), has increased the need for alternative supplementary cementitious materials. This study investigates the feasibility of using basaltic rock dust (BRD) as a high-volume replacement of FA in 3DPC through a two-stage experimental programme involving mix optimisation followed by evaluation under printing conditions. Five mortar mixes incorporating BRD at FA replacement levels of 0%, 25%, 50%, 75%, and 100% by mass were first evaluated to identify the optimum replacement level within the investigated range, after which the optimum mix was comprehensively characterised in terms of its fresh properties, rheological behaviour, hydration characteristics, mechanical performance, anisotropy, and microstructure. The results showed that 75% FA replacement by BRD achieved the optimum overall performance among the investigated BRD-containing mixes, based on the combined consideration of high BRD utilisation, flowability, hydration behaviour, and compressive strength. Although its 28-day compressive strength under conventionally cast conditions remained slightly lower than that of the control mix, under printing conditions, the C75 mix increased the flow diameter from 165 mm to 176 mm and the maximum printable layers from 14 to 16 while reducing the shape retention spread diameter from 96 mm to 89 mm. Compared with the control mix, the BRD-incorporated mix also increased the compressive strength by 10.9% in the Y- direction and 22.9% in the Z-direction, respectively, while reducing the compressive anisotropy from 20.97% to 12.39%. Although the flexural strength decreased from 7.66 to 5.02 MPa in the Y-direction and from 7.29 to 5.19 MPa in the Z-direction, the directional dependence decreased from 4.83% to 3.34%. SEM observations revealed a more compact cementitious matrix with fewer visible large pores in C75 than in the control mix. These findings demonstrate that BRD has strong potential as a high-volume replacement for FA in 3D-printed concrete, reducing reliance on fly ash while achieving favourable printability, compressive performance, and structural uniformity.
- Open Access
Utilisation of Oil-Contaminated Sand in 3D-Printed Concrete: Rheological, Mechanical, and Microstructural Assessment
The growing demand for construction materials has intensified concerns regarding natural sand depletion and the accumulation of industrial waste. Among these wastes, oil-contaminated sand (OCS) generated from petroleum-related activities presents environmental challenges while also offering potential for beneficial reuse. Previous studies have reported that low OCS contents can enhance workability and improve mechanical properties, highlighting its potential as a sustainable construction material. This study investigates the feasibility of incorporating OCS as a partial replacement for natural sand in 3D concrete printing (3DCP). Three mixes containing 0%, 0.5%, and 1% OCS were evaluated in terms of flowability, setting behaviour, printability, rheological response, hydration behaviour, mechanical performance, anisotropic response, and microstructural characteristics. The results showed that OCS incorporation had only a limited influence on flowability, while both the initial and final setting times exhibited noticeable delays. The maximum printable layers reached from 19 for the control mixture to 22 and 26 layers for the 0.5% and 1% OCS mixes, respectively, accompanied by reduced settlement and structural deformation. Rheological analysis revealed higher static yield stress and structuration rates for the OCS-modified mixes, contributing to enhanced buildability and geometric stability. Hydration calorimetry showed comparable heat-flow behaviour between the control and OCS-modified mixes, suggesting only a limited influence of OCS on cement hydration kinetics. The incorporation of OCS improved the compressive strength of the printed mixes and reduced compressive anisotropy, while SEM observations revealed a denser and more homogeneous microstructure, particularly for the 0.5% OCS mix. Thus, the findings indicate that low-level incorporation of oil-contaminated sand is a viable strategy for improving the printability and performance of 3D-printed concrete, promoting the sustainable reuse of contaminated industrial waste.
Open AccessUtilisation of Oil-Contaminated Sand in 3D-Printed Concrete: Rheological, Mechanical, and Microstructural Assessment
The growing demand for construction materials has intensified concerns regarding natural sand depletion and the accumulation of industrial waste. Among these wastes, oil-contaminated sand (OCS) generated from petroleum-related activities presents environmental challenges while also offering potential for beneficial reuse. Previous studies have reported that low OCS contents can enhance workability and improve mechanical properties, highlighting its potential as a sustainable construction material. This study investigates the feasibility of incorporating OCS as a partial replacement for natural sand in 3D concrete printing (3DCP). Three mixes containing 0%, 0.5%, and 1% OCS were evaluated in terms of flowability, setting behaviour, printability, rheological response, hydration behaviour, mechanical performance, anisotropic response, and microstructural characteristics. The results showed that OCS incorporation had only a limited influence on flowability, while both the initial and final setting times exhibited noticeable delays. The maximum printable layers reached from 19 for the control mixture to 22 and 26 layers for the 0.5% and 1% OCS mixes, respectively, accompanied by reduced settlement and structural deformation. Rheological analysis revealed higher static yield stress and structuration rates for the OCS-modified mixes, contributing to enhanced buildability and geometric stability. Hydration calorimetry showed comparable heat-flow behaviour between the control and OCS-modified mixes, suggesting only a limited influence of OCS on cement hydration kinetics. The incorporation of OCS improved the compressive strength of the printed mixes and reduced compressive anisotropy, while SEM observations revealed a denser and more homogeneous microstructure, particularly for the 0.5% OCS mix. Thus, the findings indicate that low-level incorporation of oil-contaminated sand is a viable strategy for improving the printability and performance of 3D-printed concrete, promoting the sustainable reuse of contaminated industrial waste.
- 19 January 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (3) , 2347-2372
Mechanical anisotropy and microstructural investigation of copper heap leach residue incorporated 3D printed concrete
- 19 January 2026
- Published by Springer Nature in Progress in Additive Manufacturing
- Vol. 11 (3) , 2347-2372
Mechanical anisotropy and microstructural investigation of copper heap leach residue incorporated 3D printed concrete
- Open Access
Investigation of Fresh, Mechanical, and Durability Properties of Rubberized Fibre-Reinforced Concrete Containing Macro-Synthetic Fibres and Tyre Waste Rubber
The growing disposal of used tyres and plastic waste in landfills poses a significant environmental challenge. This study investigates the potential of utilizing used tyre rubber and macro-synthetic fibres (MSFs) made from recycled plastics in fibre-reinforced rubberized concrete (RuFRC). Various percentages of tyre rubber shreds were used to replace coarse aggregates, calculated as 10%, 20%, and 30% of the volume of fine aggregates; fibre dosages (0%, 0.25%, 0.5%, 0.75%, and 1% by volume) were incorporated into the mix, and a series of physical, mechanical, and durability properties were evaluated. The results show that, as the fibre and rubber content increased, the slump of RuFRC decreased, with the lowest value obtained for concrete with 1% fibre and 30% rubber. The density of RuFRC decreases as the rubber percentage increases due to air voids and increased porosity caused by the rubber. The strength properties of RuFRC were found to decline with the increase in the rubber content, with mixes containing 30% rubber exhibiting reductions of about 60% in compressive strength, 27% in tensile strength, and 13% in flexural strength compared to the control specimen. Durability testing revealed that an increased rubber content led to higher water absorption, water penetration, and chloride ion permeability, with 30% rubber showing the highest values. However, lower rubber content (10%) and higher fibre dosages improved the durability characteristics, with water absorption reduced by up to 5% and shrinkage strains lowered by about 7%, indicating better compaction and bonding. These results indicate that RuFRC with moderate rubber and higher fibre content offers a promising balance between sustainability and performance.
Open AccessInvestigation of Fresh, Mechanical, and Durability Properties of Rubberized Fibre-Reinforced Concrete Containing Macro-Synthetic Fibres and Tyre Waste Rubber
The growing disposal of used tyres and plastic waste in landfills poses a significant environmental challenge. This study investigates the potential of utilizing used tyre rubber and macro-synthetic fibres (MSFs) made from recycled plastics in fibre-reinforced rubberized concrete (RuFRC). Various percentages of tyre rubber shreds were used to replace coarse aggregates, calculated as 10%, 20%, and 30% of the volume of fine aggregates; fibre dosages (0%, 0.25%, 0.5%, 0.75%, and 1% by volume) were incorporated into the mix, and a series of physical, mechanical, and durability properties were evaluated. The results show that, as the fibre and rubber content increased, the slump of RuFRC decreased, with the lowest value obtained for concrete with 1% fibre and 30% rubber. The density of RuFRC decreases as the rubber percentage increases due to air voids and increased porosity caused by the rubber. The strength properties of RuFRC were found to decline with the increase in the rubber content, with mixes containing 30% rubber exhibiting reductions of about 60% in compressive strength, 27% in tensile strength, and 13% in flexural strength compared to the control specimen. Durability testing revealed that an increased rubber content led to higher water absorption, water penetration, and chloride ion permeability, with 30% rubber showing the highest values. However, lower rubber content (10%) and higher fibre dosages improved the durability characteristics, with water absorption reduced by up to 5% and shrinkage strains lowered by about 7%, indicating better compaction and bonding. These results indicate that RuFRC with moderate rubber and higher fibre content offers a promising balance between sustainability and performance.
- Open Access
Effects of Partial Replacement of Cement with Fly Ash on the Mechanical Properties of Fiber-Reinforced Rubberized Concrete Containing Waste Tyre Rubber and Macro-Synthetic Fibers
This study investigates the impact of partially replacing cement with fly ash (FA) on the mechanical performance of fiber-reinforced rubberized concrete (FRRC) incorporating waste tyre rubber and recycled macro-synthetic fibers (MSF). FRRC mixtures were prepared with varying fly ash replacement levels (0%, 25%, and 50%), rubber aggregate contents (0%, 10%, and 20% by volume of fine aggregate), and macro-synthetic fiber dosages (0% to 1% by total volume). The fresh properties were evaluated through slump tests, while hardened properties including compressive strength, splitting tensile strength, and flexural strength were systematically assessed. Results demonstrated that fly ash substitution up to 25% improved the interfacial bonding between rubber particles, fibers, and the cementitious matrix, leading to enhanced tensile and flexural performance without significantly compromising compressive strength. However, at 50% replacement, strength reductions were more pronounced due to slower pozzolanic reactions and reduced cement content. The inclusion of MSF effectively mitigated strength loss induced by rubber aggregates, improving post-cracking behavior and toughness. Overall, an optimal balance was achieved at 25% fly ash replacement combined with 10% rubber and 0.5% fiber content, producing a more sustainable composite with favorable mechanical properties while reducing carbon and ecological footprints. These findings highlight the potential of integrating industrial by-products and waste materials to develop eco-friendly, high-performance FRRC for structural applications, supporting circular economy principles and reducing the carbon footprint of concrete infrastructure.
Open AccessEffects of Partial Replacement of Cement with Fly Ash on the Mechanical Properties of Fiber-Reinforced Rubberized Concrete Containing Waste Tyre Rubber and Macro-Synthetic Fibers
This study investigates the impact of partially replacing cement with fly ash (FA) on the mechanical performance of fiber-reinforced rubberized concrete (FRRC) incorporating waste tyre rubber and recycled macro-synthetic fibers (MSF). FRRC mixtures were prepared with varying fly ash replacement levels (0%, 25%, and 50%), rubber aggregate contents (0%, 10%, and 20% by volume of fine aggregate), and macro-synthetic fiber dosages (0% to 1% by total volume). The fresh properties were evaluated through slump tests, while hardened properties including compressive strength, splitting tensile strength, and flexural strength were systematically assessed. Results demonstrated that fly ash substitution up to 25% improved the interfacial bonding between rubber particles, fibers, and the cementitious matrix, leading to enhanced tensile and flexural performance without significantly compromising compressive strength. However, at 50% replacement, strength reductions were more pronounced due to slower pozzolanic reactions and reduced cement content. The inclusion of MSF effectively mitigated strength loss induced by rubber aggregates, improving post-cracking behavior and toughness. Overall, an optimal balance was achieved at 25% fly ash replacement combined with 10% rubber and 0.5% fiber content, producing a more sustainable composite with favorable mechanical properties while reducing carbon and ecological footprints. These findings highlight the potential of integrating industrial by-products and waste materials to develop eco-friendly, high-performance FRRC for structural applications, supporting circular economy principles and reducing the carbon footprint of concrete infrastructure.
- Open Access
- 26 March 2025
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 22
Sustainable 3D printed concrete incorporating alternative fine aggregates: A review
- 26 March 2025
- Published by Elsevier in Case Studies in Construction Materials
- Vol. 22
Open AccessSustainable 3D printed concrete incorporating alternative fine aggregates: A review
- 30 January 2023
- Published by Elsevier in Journal of Building Engineering
- Vol. 67
Performance evaluation of high-performance self-compacting concrete with waste glass aggregate and metakaolin
- 30 January 2023
- Published by Elsevier in Journal of Building Engineering
- Vol. 67
Performance evaluation of high-performance self-compacting concrete with waste glass aggregate and metakaolin
- Open Access
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (2) , 306-320
Investigation on the effectiveness of using building information modeling (BIM) tools in project management: a case study
Building information modeling (BIM) has brought a technological shift in the area of construction programs, resulting in a significant rise in project management performance and affordability. In Bangladesh, designers have to deal with numerous issues in implementing BIM technology as technological expertise is insufficient in this area. Therefore, the paper focuses on implementing BIM across the project life cycle and assesses its effectiveness on a construction project with respect to the Bangladeshi construction industry. For this, a 3D model simulation of a three-storied residential building is developed and all semantic data (material properties, construction details, schedules, cost of the material, etc.) is stored with the model. In addition, BIM-centered integrated project delivery techniques are analyzed for clash detection, structural analysis, scheduling (4D), and cost estimation (5D) during the planning and construction phase. The outcome of the study indicated that BIM is effective in raising whole process performance, giving precise quantity takeoffs, optimizing schedules, reducing overall project uncertainties, structural defects, and expenses. The constitutional framework of this study can lead to increased efficiency, effective communication, as well as rarer mistakes in the construction project of Bangladesh. In addition, it can be an effective tool for managing medium- and large-scale projects since it can help to boost profitability, cut expenses, and enhance time management.
- 1 January 2023
- Published by Pontificia Universidad Catolica de Chile in Revista de la construcción
- Vol. 22 (2) , 306-320
Open AccessInvestigation on the effectiveness of using building information modeling (BIM) tools in project management: a case study
Building information modeling (BIM) has brought a technological shift in the area of construction programs, resulting in a significant rise in project management performance and affordability. In Bangladesh, designers have to deal with numerous issues in implementing BIM technology as technological expertise is insufficient in this area. Therefore, the paper focuses on implementing BIM across the project life cycle and assesses its effectiveness on a construction project with respect to the Bangladeshi construction industry. For this, a 3D model simulation of a three-storied residential building is developed and all semantic data (material properties, construction details, schedules, cost of the material, etc.) is stored with the model. In addition, BIM-centered integrated project delivery techniques are analyzed for clash detection, structural analysis, scheduling (4D), and cost estimation (5D) during the planning and construction phase. The outcome of the study indicated that BIM is effective in raising whole process performance, giving precise quantity takeoffs, optimizing schedules, reducing overall project uncertainties, structural defects, and expenses. The constitutional framework of this study can lead to increased efficiency, effective communication, as well as rarer mistakes in the construction project of Bangladesh. In addition, it can be an effective tool for managing medium- and large-scale projects since it can help to boost profitability, cut expenses, and enhance time management.
- 7 December 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 64
Eco-friendly and cost-effective self-compacting concrete using waste banana leaf ash
- 7 December 2022
- Published by Elsevier in Journal of Building Engineering
- Vol. 64
Eco-friendly and cost-effective self-compacting concrete using waste banana leaf ash