Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Bunsita Wongvasana has a total of 5 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Structure–Property Correlation in Natural Rubber Nanocomposite Foams: A Comparison between Nanoclay and Cellulose Nanofiber Used as Nanofillers

    by Bunsita Wongvasana, Bencha Thongnuanchan, Abdulhakim Masa, Hiromu Saito, Tadamoto Sakai, Natinee Lopattananon

    Nanocomposite foams of natural rubber (NR) with 5 phr of two kinds of nanofillers, nanoclay (NC) and cellulose nanofiber (CNF), were produced using the latex mixing method and foaming with azodicarbonamide. The effect of the nanofiller on the structure and mechanical properties of NR foams was investigated through SEM, TEM, tensile tests, WAXD, and compression set measurements. Smaller cells with a narrower distribution were attained in the NC/NR foam when compared to the NR and CNF/NR foams, and the expansion ratio was larger due to the suppression of the shrinkage in the NC/NR foam. The foaming of the NR nanocomposites reduced the size of the filler aggregates and improved the dispersion and alignment of nanofillers in the cell walls. The addition of NC and CNF enhanced the tensile strength of the NR foam by 139% and 62%, respectively, without sacrificing the excellent strain of the NR, due to the acceleration of the strain-induced crystallization and small size of the filler aggregates. The compression set of the NR foam could also be reduced in the NC/NR foam compared with the NR and CNF/NR foams.


  • Open Access

    Reinforcement Behavior of Chemically Unmodified Cellulose Nanofiber in Natural Rubber Nanocomposites

    by Bunsita Wongvasana, Bencha Thongnuanchan, Abdulhakim Masa, Hiromu Saito, Tadamoto Sakai, Natinee Lopattananon

    We investigated the reinforcement behavior of small amounts of chemically unmodified cellulose nanofiber (CNF) in eco-friendly natural rubber (NR) nanocomposites. For this purpose, NR nanocomposites filled with 1, 3, and 5 parts per hundred rubber (phr) of cellulose nanofiber (CNF) were prepared by a latex mixing method. By using TEM, a tensile test, DMA, WAXD, a bound rubber test, and gel content measurements, the effect of CNF concentration on the structure–property relationship and reinforcing mechanism of the CNF/NR nanocomposite was revealed. Increasing the content of CNF resulted in decreased dispersibility of the nanofiber in the NR matrix. It was found that the stress upturn in the stress–strain curves was remarkably enhanced when the NR was combined with 1–3 phr CNF, and a noticeable increase in tensile strength (an approximately 122% increase in tensile strength over that of NR) was observed without sacrificing the flexibility of the NR in the NR filled with 1 phr CNF, though no acceleration in their strain-induced crystallization was observed. Since the NR chains were not inserted in the uniformly dispersed CNF bundles, the reinforcement behavior by the small content of CNF might be attributed to the shear stress transfer at the CNF/NR interface through the interfacial interaction (i.e., physical entanglement) between the nano-dispersed CNFs and the NR chains. However, at a higher CNF filling content (5 phr), the CNFs formed micron-sized aggregates in the NR matrix, which significantly induced the local stress concentration and promoted strain-induced crystallization, causing a substantially increased modulus but reduced the strain at the rupture of the NR.


  • Open Access

    Comparative Structure–Property Relationship between Nanoclay and Cellulose Nanofiber Reinforced Natural Rubber Nanocomposites

    by Bunsita Wongvasana, Bencha Thongnuanchan, Abdulhakim Masa, Hiromu Saito, Tadamoto Sakai, Natinee Lopattananon

    Natural rubber (NR) nanocomposites reinforced with five parts per hundred rubber (phr) of two different nano-fillers, i.e., nanoclay (abbrev. NC) and cellulose nanofiber (abbrev. CNF), were prepared by using latex mixing approach, followed by mill-compounding and molding. The morphology, stress–strain behavior, strain-induced crystallization, and bound rubber of the NR nanocomposites were systematically compared through TEM, tensile test, WAXS, DMA, and bound rubber measurement. The aggregated CNFs were observed in the NR matrix, while the dispersed nanosized clay tactoids were detected across the NR phase. The reinforcement effects of NC and CNF were clearly distinct in the NR nanocomposites. At the same nano-filler content, the addition of NC and CNF effectively accelerated strain-induced crystallization of NR. The high tensile strength obtained in the NC-filled NR nanocomposite was attributed to strain-induced crystallization of NR accelerated by well-dispersed NC. However, the larger tensile modulus and low strain for the CNF-filled NR were related to the formation of immobilized NR at the interface between CNF aggregate and NR. The immobilization effect of NR at the CNF surface offered by a mutual entanglement of CNF aggregate and NR chain led to local stress concentration and accelerated strain-induced crystallization of CNF/NR nanocomposite. From the present study, the NR nanocomposites combined with 5 phr CNF shows high-tensile modulus and acceptable breaking tensile stress and strain, suggesting the application of CNF/NR based nanocomposite in automotive and stretchable sensors for next-generation electronic devices.