Wei Wei
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Wei Wei has a total of 21 co-authors. Here are the top co-authors by number of shared publications:
Shibo Cai
4 shared publications- Mingyu Du
The College of Mechanical Engineering, Zhejiang University of Technology
3 shared publications Guanjun Bao
2 shared publicationsMingyu Du
2 shared publicationsBangda Zhou
Zhejiang University of Technology
1 shared publicationBingfei Fan
Zhejiang University of Technology
1 shared publication
Latest Publications
- 7 May 2026
- Published by Elsevier in Mechatronics
- Vol. 118
Design, modeling, and control of a multi-link horizontal lower-limb rehabilitation robot
- 7 May 2026
- Published by Elsevier in Mechatronics
- Vol. 118
Design, modeling, and control of a multi-link horizontal lower-limb rehabilitation robot
- 18 April 2026
- Published by Elsevier in Biomedical Signal Processing and Control
- Vol. 121
An online active lower-limb rehabilitation training system based on motor imagery fNIRS signals
- 18 April 2026
- Published by Elsevier in Biomedical Signal Processing and Control
- Vol. 121
An online active lower-limb rehabilitation training system based on motor imagery fNIRS signals
- 24 October 2025
- Published by Springer Nature
- p. 298-309
Multidimensional Kinematic Analysis of Walking and Turning in Older Adults Using IMUs
- 24 October 2025
- Published by Springer Nature
- p. 298-309
Multidimensional Kinematic Analysis of Walking and Turning in Older Adults Using IMUs
- 20 October 2025
- Published by Elsevier in Neurocomputing
- Vol. 660
DBTSP-net: A temporal-spatial parallel network with optuna optimization for subject-specific motor imagery EEG decoding and visualization
- 20 October 2025
- Published by Elsevier in Neurocomputing
- Vol. 660
DBTSP-net: A temporal-spatial parallel network with optuna optimization for subject-specific motor imagery EEG decoding and visualization
- Open Access
- 8 September 2022
- Published by Springer Nature in Research Square
An Adaptive Hand exoskeleton for Teleoperation System
Teleoperation can assist humans in completing various complex tasks in inaccessible or high-risk environments. Adequate adaptability should be available to enable the exoskeleton master hand to capture the motion of human fingers and reproduce the contacting force between the slave hand and its object. This paper presents a novel finger exoskeleton based on the cascading four-link closed-loop kinematic chain. Each finger has an independent kinematic chain, and the angle sensor is employed to measure the finger movement including the flexion/extension and the adduction/abduction angle. The servo motor controls the tension of the tendon to transmit the contacting force to the fingers in real-time. An adaptive hand exoskeleton is consequently developed based on the finger exoskeleton. The experiment results show that the adaptive hand exoskeleton could be worn without any mechanical constraints, and the slave hand could follow the motions of each human finger. The accuracy and the real-time capability of the contacting force reproduction were validated to be superior. The designed adaptive hand exoskeleton could be employed as the master hand to remotely control the humanoid five-fingered dexterous slave hand, thus, enabling the teleoperation system to complete complex dexterous manipulation tasks.
- 8 September 2022
- Published by Springer Nature in Research Square
Open AccessAn Adaptive Hand exoskeleton for Teleoperation System
Teleoperation can assist humans in completing various complex tasks in inaccessible or high-risk environments. Adequate adaptability should be available to enable the exoskeleton master hand to capture the motion of human fingers and reproduce the contacting force between the slave hand and its object. This paper presents a novel finger exoskeleton based on the cascading four-link closed-loop kinematic chain. Each finger has an independent kinematic chain, and the angle sensor is employed to measure the finger movement including the flexion/extension and the adduction/abduction angle. The servo motor controls the tension of the tendon to transmit the contacting force to the fingers in real-time. An adaptive hand exoskeleton is consequently developed based on the finger exoskeleton. The experiment results show that the adaptive hand exoskeleton could be worn without any mechanical constraints, and the slave hand could follow the motions of each human finger. The accuracy and the real-time capability of the contacting force reproduction were validated to be superior. The designed adaptive hand exoskeleton could be employed as the master hand to remotely control the humanoid five-fingered dexterous slave hand, thus, enabling the teleoperation system to complete complex dexterous manipulation tasks.