Fanxing Li
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Previous Organizations / Institutes
The organizations / institutes from the scholar's other articles in the past ten years
Research Subjects
Fanxing Li has a total of 12 co-authors. Here are the top co-authors by number of shared publications:
- Lei Song
School of Aeronautic Science and Engineering, Beihang University, Beijing 100191, China
2 shared publications - Xiaoqiang Lu
School of Aeronautic Science and Engineering, Beihang University, Beijing 100191, China
2 shared publications - Boqian Ji
School of Aeronautic Science and Engineering, Beihang University, Beijing 100191, China
1 shared publication - Danping Zou
Shanghai Jiao Tong University
1 shared publication - Fangyu Sun
Shanghai Jiao Tong University
1 shared publication - Gang Lin
Chinese Flight Test Establishment, Xi’an, China
1 shared publication
Latest Publications
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (12) , 14292-14299
Ask to Land: Learning a Mask-Conditioned Open-Vocabulary Landing Policy via Differentiable Physics
- 1 December 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Robotics and Automation Letters
- Vol. 11 (12) , 14292-14299
Ask to Land: Learning a Mask-Conditioned Open-Vocabulary Landing Policy via Differentiable Physics
- 12 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. 60 (6) , 9221-9230
Preliminary Layout Design Method of Flush Airdata Sensing System
The flush airdata sensing system (FADS) is a measurement method that calculates aircrafts airdata by obtaining the pressure distribution from the ports. The traditional design method of port layout is to install the ports on the side of aircraft nose where the pressure is sensitive to angle of sideslip and angle of attack. Yet, for the aircraft whose surface pressure gradient with respect to angle of sideslip is rather slighter than that with respect to angle of attack, especially for blended wing body configuration, its measurement errors of angle of sideslip will increase significantly. In order to enhance the measurement accuracy, this paper proposes a resolution-based port layout design method for plane aircrafts while the traditional gradient-based design method deteriorates. Firstly, the pressure distribution of aircraft under various cases are obtained by computational fluid dynamics method, and then the feasible set of ports is introduced. Secondly, the layouts under different port counts are gained by resolution-based method and traditional method respectively. Finally, it establishes FADS to predict the angle of attack, angle of sideslip and airspeed by artificial neural network, and evaluates the performance of resolution-based method and traditional method. The result shows that, the resolution-based method obtains the optimal layout, and has a quite minor error and system uncertainty than traditional method, which effectively improves the system's accuracy.
- 12 August 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Aerospace and Electronic Systems
- Vol. 60 (6) , 9221-9230
Preliminary Layout Design Method of Flush Airdata Sensing System
The flush airdata sensing system (FADS) is a measurement method that calculates aircrafts airdata by obtaining the pressure distribution from the ports. The traditional design method of port layout is to install the ports on the side of aircraft nose where the pressure is sensitive to angle of sideslip and angle of attack. Yet, for the aircraft whose surface pressure gradient with respect to angle of sideslip is rather slighter than that with respect to angle of attack, especially for blended wing body configuration, its measurement errors of angle of sideslip will increase significantly. In order to enhance the measurement accuracy, this paper proposes a resolution-based port layout design method for plane aircrafts while the traditional gradient-based design method deteriorates. Firstly, the pressure distribution of aircraft under various cases are obtained by computational fluid dynamics method, and then the feasible set of ports is introduced. Secondly, the layouts under different port counts are gained by resolution-based method and traditional method respectively. Finally, it establishes FADS to predict the angle of attack, angle of sideslip and airspeed by artificial neural network, and evaluates the performance of resolution-based method and traditional method. The result shows that, the resolution-based method obtains the optimal layout, and has a quite minor error and system uncertainty than traditional method, which effectively improves the system's accuracy.
- 25 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-8
Enhancement of Insensitivity for Pitot-Static Probe by Static-Pressure Orifices Optimization
Range of insensitivity is a crucial characteristic for pitot-static probe, and it is defined as the range of aerodynamic angle where the measurement error does not exceed acceptable tolerance. This article proposes a static orifice design in order to extend the range of insensitivity for static pressure measurement. The assumption of pressure in the static pressure cavity of a multiorifice pitot-static probe is empirically proposed and verified by wind tunnel test. Based on this assumption, the circumferential distribution of orifices for ten-orifice pitot-static probe is optimized using the adaptive simulated annealing (ASA) algorithm. After optimization, within −15° to −25° angle of attack (AOA) and 0°–15° angle of sideslip (AOS), the weighted static pressure coefficient error decreases from 0.0331 to 0.0249. The range of insensitivity is reduced by 5° in AOA direction but extended by 5° in AOS direction, where the experiment shows a good acceptance with numerical results.
- 25 March 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Instrumentation and Measurement
- Vol. 71 (00189456) , 1-8
Enhancement of Insensitivity for Pitot-Static Probe by Static-Pressure Orifices Optimization
Range of insensitivity is a crucial characteristic for pitot-static probe, and it is defined as the range of aerodynamic angle where the measurement error does not exceed acceptable tolerance. This article proposes a static orifice design in order to extend the range of insensitivity for static pressure measurement. The assumption of pressure in the static pressure cavity of a multiorifice pitot-static probe is empirically proposed and verified by wind tunnel test. Based on this assumption, the circumferential distribution of orifices for ten-orifice pitot-static probe is optimized using the adaptive simulated annealing (ASA) algorithm. After optimization, within −15° to −25° angle of attack (AOA) and 0°–15° angle of sideslip (AOS), the weighted static pressure coefficient error decreases from 0.0331 to 0.0249. The range of insensitivity is reduced by 5° in AOA direction but extended by 5° in AOS direction, where the experiment shows a good acceptance with numerical results.