SSShigeru Suzuki

Shigeru Suzuki

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article

Previous Organizations / Institutes

The organizations / institutes from the scholar's other articles in the past ten years


Shigeru Suzuki has a total of 99 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Characterization of Residual Stress and Microstructure in a Functional Iron-Gallium Single Crystal Alloy

    by Shigeru Suzuki, Masaki Chiba, Takenori Tanno, Shuichiro Hashi, Kazushi Ishiyama

    X-ray diffraction (XRD) and scanning electron microscopy (SEM) in combination with electron backscatter diffraction (EBSD) were used to evaluate the residual stresses and microstructure of a functional Fe-Ga single crystal alloy. The single crystal was subjected to electrical discharge machining (EDM) and tensile deformation. A surface layer of polycrystalline grains was formed by EDM, and the residual stress of the single crystal was measured with the surface layer. The residual stresses in the surface layer revealed that the maximum principal stress of the alloy increased along the tensile direction during deformation, the results obtained by SEM-EBSD indicated that band-like microstructures corresponding to the {112}〈111〉 slip system were formed on the fracture surface after deformation. The observed traces of slip surfaces corresponded to deformation twins formed in the alloy. The results evaluated using XRD showed a correlation between the principal residual stresses and the microstructure observed by SEM-EBSD. The large principal stresses were found to be consistent with the direction of the applied tensile stress. Furthermore, the residual stresses were shown to change abruptly from tensile to compressive due to the shrinkage of the alloy at rupture. In addition, the residual stresses were shown to change abruptly from tensile to compressive due to the shrinkage of the alloy at rupture. These results indicate that stress measurements of single crystal alloys can be effectively performed by inducing polycrystals formed on the surface layer by EDM, and provide valuable insight into the stress distribution characteristics of such single crystal alloys due to deformation.


  • Open Access

    Stability of Oxidation State of Fe in Organic Acid Complex

    by Masahito Uchikoshi, Shigeru Suzuki

    Oral iron medications, a treatment for iron deficiency anemia, frequently cause side effects such as nausea, vomiting, and diarrhea. The mechanism of toxicity has not been elucidated, and therefore measures to reduce toxicity have not been established. The influence of the oxidation state of iron is considered as one of the factors that may cause side effects, so the oxidation state of iron was confirmed using ultraviolet-visible absorption spectroscopy when oral iron medications dissolve in the stomach. The main components of oral iron medications are inorganic and organic acid iron complexes, with citric acid, fumaric acid, sulfuric acid, etc. used as ligands. The influence of the valence of the ligand on the stability of the oxidation state of iron was also examined.


  • Open Access

    Density and Surface Tension Measurement of Fe-Ga Melts Using Electromagnetic Levitation Technique

    by Masayoshi Adachi, Hideo Higashi, Ikuma Nagakusa, Toru Kawamata, Tsuyoshi Kumagai, Tsuguo Fukuda, Shigeru Suzuki, Hiroyuki Fukuyama

    Fe-Ga alloys are expected as a magnetostrictive material. Currently, Fe-Ga single crystals have been fabricated by the Czochralski method. Thermophysical properties of the Fe-Ga melt are necessary for the improvement of the crystal growth technique, however, these have not measured to date. The aim of this study was therefore to measure the density and surface tension of Fe-Ga melts using electromagnetic levitation technique. It is possible to measure thermophysical property of sample melts at undercooling condition using the electromagnetic levitation method. The density and surface tension of the Fe-Ga decreased with increasing temperature including supercooling temperature region. The molar volume of the Fe-Ga melt is smaller than the molar volume calculated assuming ideal solution. The surface tension of the Fe-Ga melt was in good agreement with the surface tension calculated from Butler model.

  • Open Access

    Residual Stresses in Polycrystalline Iron Alloys Measured by X-ray Diffraction and Related Microstructure

    by Shigeru Suzuki, Shigeo Sato, Susumu Imashuku, Hiroyuki Sato, Shun-Ichiro Tanaka

    This article describes results of the residual stress measurements in different iron alloys using a few non-destructive techniques based on X-ray diffraction. It was shown that the results provide useful information for understanding the microstructural phenomenon in each alloy, although these techniques are not universally applicable to various cases. In this paper, the residual stresses formed during stress-induced martensitic transformation and its reverse transformation in shape memory alloys, the residual stresses balancing between two phases in duplex stainless steels and the residual stresses formed by inhomogeneous plastic strains in polycrystalline twin-induced plasticity steels are shown. It is important to select an adequate method according to the phenomena and properties of interest in iron alloys. The residual stresses formed in a high-entropy alloy containing iron are also presented, taking into account into the inhomogeneity in bulk. The residual stresses and related microstructural data in materials in structures and device components are considered to be effective parameters for evaluating their mechanical properties. While modern diffraction measurement methods are relatively easy to be operated, it is noted that the results include issues related to the microstructure of the materials. These issues should also be discussed in the residual stress measurements at different scales, and reliable fundamental data related to residual stress considering the microstructure would be necessary for discussion.


  • Open Access

    Characterization of Anisotropic Properties of Functional Iron Alloy Sheets

    by Masahito Watanabe, Kiyoshi Urakawa, Yoshio Ishigaki, Taisuke Furuse, Motohiro Kasuya, Shigeo Sato, Shigeru Suzuki

    To understand the anisotropy of properties in FeCo-V alloy sheets, the Young's modulus, texture, and residual stress of samples of different treatments were investigated using the X-ray diffraction method. In the cold-rolled alloy sheets, the anisotropy of Young's modulus in different directions within the sheet plane was similar to that of the annealed samples at 600 °C, although there was some variation. The anisotropy of the Young's modulus was different from that of the cold-rolled and annealed samples at low temperatures. According to the results of texture measurements on alloy sheets subjected to each treatment, the direction of the lower Young's modulus almost corresponds to a specific texture component, suggesting that the texture component affects the anisotropy of the Young's modulus. X-ray diffraction rings from alloy sheets are used in the residual stress measurement, which may contain information on the process of alloy sheets and changes in the texture due to heat treatment. Residual stress shows anisotropy within the surface of cold-rolled alloy sheets, indicating high compressive residual stress in the rolling direction and in the transverse direction. In general, lower residual stress in the sheets annealed at 600 °C may be related to dislocation rearrangement in the alloys. Furthermore, in the samples annealed at 850 °C, recrystallization and related phenomena are reflected in the deviation from the plot for residual stress, which may also affect the texture.

  • Open Access

    Strain and Magnetic Field Changes in Vibration of Devices Attached Iron Alloys with Large Magnetostriction

    by Masaki Chiba, Kensuke Misawa, Hisanori Tanimoto, Masayoshi Kumagai, Shigeo Sato, Toru Kawamata, Shigeru Suzuki

    To understand the mechanism of vibration energy harvesting using magnetostrictive Fe-Ga alloys, the dynamic strains at different locations of a U-shaped device during vibration were simulated. In the simulations, the previous results for location-dependent strain in the vibration experiments were fitted with trigonometric functions. The results show that the amplitude and phase of the strain vary with location, and that the electromagnetic force is generated at different locations. Since magnetic induction is thought to occur due to an external magnetic field, the magnetic domain structure near the cube orientation of Fe-Ga alloy single crystals was observed using a Kerr effect microscope. As a result, Bloch magnetic domain structures with different contrasts of brightness and darkness were observed depending on the applied magnetic field. It was shown that striped magnetic domains were dominant when the applied magnetic field was small, while lancet magnetic domains oriented to the magnetic field appeared with transverse straight supplementary domains as a magnetic domain under a saturated magnetic field. The domain patterns in one direction magnetic fields were not necessarily the same as those observed in the opposite direction. This indicates that Fe-Ga alloy single crystals are used as a core for vibrational energy harvesting. Also, the motion of magnetic walls is thought to play an important role in the vibrational properties of the material, and inhomogeneous elastic strain associated with magnetic domains evolves microscopically in single crystals.


  • Open Access

    Structural Analysis Methods for Characterizing Multicomponent Melts and Glasses Processed at High Temperatures

    by Shigeru Suzuki, Sohei Sukenaga, Tsuyoshi Nishi, Kozo Shinoda, Hiroyuki Shibata

    Recent structural-analysis research was reviewed for characterizing multicomponent melts and glasses processed at high temperatures. Multicomponent melts and glasses are often formed in slags during pyrometallurgical processing and the vitrification of highly radioactive wastes from nuclear power plants. Melt and glass physical properties were interpreted based on structural analyses using different methods. For example, the viscosities of different molten-silicate compositions were explained based on Raman and magic-angle-spinning magnetic resonance (MAS NMR) spectra. In addition, the thermal conductivities of multicomponent vitrified glasses were examined based on the structures elucidated using MAS NMR spectroscopy. X-ray absorption spectroscopy, which provides information about element chemical states, is used to analyze the local structure around specific elements in both melts and glasses. These studies show that structural analysis methods provide important information for designing and controlling melts and glasses processed at high temperatures. The structures characterized using different analysis methods were presented to elucidate the physical properties of multicomponent melts and glasses processed at high temperatures and propose prospects and directions for further research of process-oriented methods.


  • Open Access

    Characterization of the Incorporation and Adsorption of Arsenate and Phosphate Ions into Iron Oxides in Aqueous Solutions

    by Kozo Shinoda, Takenori Tanno, Yuki Nakata, Shigeru Suzuki

    This article provides an overview of the incorporation and adsorption of arsenate and phosphate into iron oxides formed in aqueous solutions. Although arsenic (As) and phosphorus (P) and belong to the same group in the periodic table, As is usually toxic, whereas P is a biological element. Arsenate and phosphate ions can be incorporated into iron oxides through different routes, depending on the solution conditions. In aqueous solutions, the chemical state of Fe in iron oxides is FeII (ferrous) or FeIII (ferric), that of As is AsIII (arsenite) and AsV (arsenate), and that of phosphorus is PV (phosphate). The composition and structure of iron oxides, including ferric oxyhydroxides and hydroxides formed in aqueous solutions, are affected by solution conditions such as the electrochemical potential, pH, temperature, and the chemical state and composition of the relevant elements. Moreover, arsenate and phosphate ions are usually adsorbed on the surface of iron oxides in aqueous solutions, but the incorporation and adsorption of arsenate and phosphate ions in iron oxides cannot be easily explained using simple thermodynamic models. This is because these characteristics are accompanied by different stages of coprecipitation, incongruent dissolution of multicomponent iron oxides, and so on. Since hydrated iron-oxide particles are often very fine and poorly crystallized, they are difficult to filter. However, it has been shown that coarse polyhedral particles of hydrated iron oxide can be synthesized by oxidizing FeII ions. In addition, the coarse particles of hydrated iron oxide are transformed into agglomerates of fine FeIII oxides with a coarse outer shell by alkaline treatment, and these coarse porous iron-oxide particles exhibit good anion-adsorption capacity in aqueous solutions. The formation mechanisms of these different iron-oxide particles are discussed based on the results of the incorporation and adsorption of arsenate and phosphate ions in iron oxides in aqueous solutions.

  • Open Access

    Characterization of α-Al2O3 in Structural Isomers of Alumina Formed by Oxidation of Fe–Cr–Al Alloys

    by Susumu Imashuku, Michihisa Fukumoto, Kano Nakajima, Shigeru Suzuki

    To understand the formation of structural isomers of alumina (Al2O3) on the surfaces of Fe–Cr–Al alloys, cathodoluminescence (CL), X-ray photoelectron spectroscopy (XPS), and X-ray diffraction (XRD) were used. The alloys were annealed under oxygen at a low partial pressure to focus on the initial formation of Al2O3. XRD revealed that corundum (α-Al2O3) was predominantly formed on the alloy surfaces after annealing at approximately 1100°C, whereas γ-Al2O3 and θ-Al2O3 were formed at 1000°C. CL peaks around 700 nm, which originated from Cr3+ ions in Al2O3, was drastically increases by rising the annealing temperatures from 1000 to 1100°C because of the increase of the chromium content in the Al2O3 scales that was revealed by XPS. EPMA revealed that the surficial α-Al2O3 had striped patterns, which were similar to those observed using CL imaging, indicating that CL can be conveniently used for imaging α-Al2O3 and analyzing the inhomogeneous distribution of α-Al2O3 on the alloys.


  • Open Access

    Microscale Changes in Microstructure and Stress Distribution in Duplex Stainless Steel Caused by Plastic Deformation

    by Shun-Ichiro Tanaka, Shigeo Sato, Kengo Matsuda, Masaki Chiba, Shigeru Suzuki

    Microscale changes in the microstructure of and stress distribution in a polycrystalline duplex stainless steel comprising ferrite and austenite caused by plastic tensile deformation are characterized to understand the microscopic processes of the crystal plasticity of dual-phase steel. Because the ferrite of the body-centered-cubic structure and the austenite of the face-centered-cubic structure exhibit different mechanical properties, texture changes in the ferrite and austenite caused by uniaxial tensile deformation are investigated based on the electron backscatter diffraction pattern. Residual stresses formed by tensile deformation are characterized using a two-dimensional method based on X-ray diffraction. The results show that the steel exhibits a banded microstructure of ferritic coarse grains and austenitic fine grains, and that the texture is changed by tensile deformation. The grains in the steel are rotated by tensile deformation depending on their orientation with respect to the tensile axis. Residual stress measurements demonstrate that compressive stresses remain in the elastically hard ferrite after tensile deformation, whereas tensile stresses remain in the austenitic phase. The formation of the residual stresses are discussed based on the characteristic microscale plasticity of ferrite and austenite.