CLChong Liang

Chong Liang

*This is an algorithmically generated author record based on publicly available information.

Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Chong Liang has a total of 13 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Selection and Optimization Design of PDC Bits Based on FEM Analysis for Drilling Long Horizontal Sections of Shale Formations

    by Lulin Kong, Zhaowei Wang, Haige Wang, Mingyue Cui, Chong Liang, Xiangwen Kong, Ping Wang

    Well structures with ultra-long sections have become one of the most applied technologies in the field of shale gas development. While there have been many technical challenges, enhancing the breaking efficiency and stability of polycrystalline diamond compact (PDC) bits has become an essential issue of focus. Since 2013, the well structure in the Duvernay area has been optimized multiple times, and the rate of penetration (ROP) of the entire wellbore has nearly doubled. However, there are significant differences in terms of the performances of different PDC bits, and there is still room for improvement to optimize these drill bits. For this reason, a confined compressive strength test was conducted to obtain the rock mechanical parameters from shale cores extracted from the long horizontal section. Using these data, a finite element model (FEM) was developed with a corresponding scale. A calibration of the elastic-plastic damage constitutive models was then performed using the FEM. The breaking mechanism of three different PDC bits was examined using a “PDC bit-bottom hole” interaction FEM model, facilitating guidance for bit selection and design optimization: (1) The type B PDC bit, which has four blades and 20 cutters, exhibited the highest mechanical specific energy (MSE) and the lowest vibration across three directional mechanical characteristics. This design is recommended for engineering applications. (2) Lower axial vibrations were produced when the CDE was used as the rear element when compared to those when using the BHE. However, an increase within an acceptable range was observed in the TOB and circumferential vibrations. Thus, for redesigning work on the type B bit, the assembly of the CDE is suggested. (3) A decrease in the MSE and vibration in three directional mechanical characteristics was observed when the depth of cut (DOC) was varied between 1.5 and 2.0 mm. A broadening in the range of lateral forces was noted when a DOC of 2.0 mm was used. Therefore, for the redesign of the type B bit, the assembly of CDEs as rear elements at a DOC of 1.5 mm is recommended. In conclusion, a new practical method for the selection and optimization of PDC bit design, based on rock mechanics and the FEM theory, is proposed.


  • Open Access

    A Review of the Hydraulic Fracturing in Ductile Reservoirs: Theory, Simulation, and Experiment

    by Dawei Zhu, Guofeng Han, Honglan Zou, Mingyue Cui, Chong Liang, Fei Yao

    The bottom-hole pressure of hydraulic fracturing in ductile reservoirs is much higher than that of the hydraulic fracturing simulation, and the fracture toughness inferred from the field data is 1–3 orders of magnitude higher than that measured in the laboratory. The rock apparent fracture toughness increases with the increase in the confining pressure. Excluding the influence of the fluid viscosity and the fluid lag on the apparent fracture toughness, the fracture process zone (FPZ) at the fracture tip can explain the orders of magnitude of difference in the apparent fracture toughness between the laboratory and the field. The fracture tip is passivated by plastic deformation, forming a wide and short hydraulic fracture. However, the size of the FPZ obtained in the laboratory is in the order of centimeters to decimeters, while an FPZ of 10 m magnitude is speculated in the field. The FPZ size is affected by the rock property, grain size, pore fluid, temperature, loading rate, and loading configuration. It is found that the FPZ has a size effect that tends to disappear when the rock specimen size reaches the scale of meters. However, this cannot fully explain the experience of hydraulic fracturing practice. The hydraulic fracturing behavior is also affected by the relation between the fracture toughness and the fracture length. The fracture behavior of type II and mixed type for the ductile rock is poorly understood. At present, the apparent fracture toughness model and the cohesive zone model (CZM) are the most suitable criteria for the fracture propagation in ductile reservoirs, but they cannot fully characterize the influence of the rock plastic deformation on the hydraulic fracturing. The elastic-plastic constitutive model needs to be used to characterize the stress–strain behavior in the hydraulic fracturing simulation, and the fracture propagation criteria suitable for ductile reservoirs also need to be developed.


  • Open Access

    Acid System and Stimulation Efficiency of Multistage Acid Fracturing in Porous Carbonate Reservoirs

    by Dawei Zhu, Yunjin Wang, Mingyue Cui, Fujian Zhou, Yaocong Wang, Chong Liang, Honglan Zou, Fei Yao

    With little to no natural fracture development and the high calcite content in porous carbonate reservoirs, for multistage acid fracturing, different fluids are used to form a viscous fingering in the fracture, thus enhancing the degree of nonuniform etching. However, existing studies on multistage acid fracturing mainly focused on the combination of fracturing fluid and acid, which is less specific for porous carbonate rocks. Here, the rheological properties of five fluids, including guar-based fluid, cross-linked guar, gelled acid, cross-linked acid, and diverting acid, were studied at each temperature condition, and the viscosity relationship between each fluid was clarified. Based on the rheological properties, the differences between the seven liquid combinations on the etched morphology of the fracture walls were studied and analyzed. The conductivity of the seven acid-etched fractures under different closure stress was simulated. The experimental results showed that the viscosity relationships between the fluids at different temperatures were cross-linked guar > cross-linked acid > diverting acid (spent acid) > gelled acid > guar-based liquid > diverting acid (fresh acid). Because cross-linked acid has higher viscosity than gelled acid, it can form more obvious viscous fingering with a variety of liquids, which is more suitable for acid fracturing stimulation of porous carbonate reservoirs. In addition, the combination of cross-linked and diverting acids was screened out. The multistage alternate injection of this fluid combination could form tortuous and complex etching channels, and its acid-etching fracture conductivity was significantly higher than that of other fluid combinations at different closure stress. In this study, we optimized the fluid combination of porous carbonates and clarified the effect and mechanism of nonuniform etching to provide guidance for the fluid combination selection of multistage alternate acid fracturing process for porous carbonate reservoirs.