Pascal Piluso
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Pascal Piluso has a total of 22 co-authors. Here are the top co-authors by number of shared publications:
- Jules Delacroix
CEA, DES, IRESNE, DTN, SMTA, Severe Accident Experimental Laboratory, Cadarache, Saint-Paul-Lez-Durance, France
3 shared publications - Benjamin Turquais
CEA, DES, IRESNE, DTN 1 , Cadarache, F-13108 Saint-Paul-Lez-Durance, France
2 shared publications - Christophe Journeau
CEA, DES, IRESNE, DTN, Severe Accident Experimental Laboratory
2 shared publications Nourdine Chikhi
CEA, DES, IRESNE, DEC 4 , Cadarache, F-13108 Saint-Paul-Lez-Durance, France
2 shared publicationsSarah Thilliez
2 shared publicationsArthur Denoix
CEA, IRESNE, DTN, SMTA, LEAG, Cadarache, F-13108 Saint-Paul-Lez-Durance, France
1 shared publication
Latest Publications
- Open Access
- 1 December 2025
- Published by EDP Sciences in EPJ Nuclear Sciences & Technologies
- Vol. 11, 75
Identification of European experimental facilities for severe accident research within EU SEAKNOT-project: Analysis and mapping
Experimental facilities play a central role in reactor safety research for both design basis and severe accidents (SA). They are key to demonstrate the effectiveness and appropriateness of specific safety features of reactor designs and providing data for the validation of different models implemented in numerical tools used for safety demonstration. Hence, a well-designed and equipped experimental infrastructures in Europe is a fundamental pillar of European roadmap on reactor safety research. One objective of the EU SEAKNOT (Severe Accident research and KNOwledge management) project, is the analysis and mapping of European severe accident research facilities currently under operation. The responses to a questionnaire sent to European institutions were evaluated and the information collected about each facility was synthesized covering different issues such as age, design features, main phenomena addressed by latest research programs, including advanced technologies like Advanced Technology Fuels (ATFs) and Small Modular Reactors (SMRs). The extensive review of the collected information allowed the identification of critical conditions (human resources; preservation and enhancement of experimental competences, etc. that might jeopardize the current and forthcoming European experimental capabilities for severe accident research, according to the Severe Accident roadmap that is being built in SEAKNOT. This paper describes the methodology and major outcomes of this analysis.
- 1 December 2025
- Published by EDP Sciences in EPJ Nuclear Sciences & Technologies
- Vol. 11, 75
Open AccessIdentification of European experimental facilities for severe accident research within EU SEAKNOT-project: Analysis and mapping
Experimental facilities play a central role in reactor safety research for both design basis and severe accidents (SA). They are key to demonstrate the effectiveness and appropriateness of specific safety features of reactor designs and providing data for the validation of different models implemented in numerical tools used for safety demonstration. Hence, a well-designed and equipped experimental infrastructures in Europe is a fundamental pillar of European roadmap on reactor safety research. One objective of the EU SEAKNOT (Severe Accident research and KNOwledge management) project, is the analysis and mapping of European severe accident research facilities currently under operation. The responses to a questionnaire sent to European institutions were evaluated and the information collected about each facility was synthesized covering different issues such as age, design features, main phenomena addressed by latest research programs, including advanced technologies like Advanced Technology Fuels (ATFs) and Small Modular Reactors (SMRs). The extensive review of the collected information allowed the identification of critical conditions (human resources; preservation and enhancement of experimental competences, etc. that might jeopardize the current and forthcoming European experimental capabilities for severe accident research, according to the Severe Accident roadmap that is being built in SEAKNOT. This paper describes the methodology and major outcomes of this analysis.
- 31 October 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 619
Iron and 304L-stainless steel oxidation under oxygen and steam atmosphere at high temperature from 1350°C to 1600°C
- 31 October 2025
- Published by Elsevier in Journal of Nuclear Materials
- Vol. 619
Iron and 304L-stainless steel oxidation under oxygen and steam atmosphere at high temperature from 1350°C to 1600°C
- 1 September 2022
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 93 (9) , 094901
Pyroreflectometry as a technique for the accurate measurement of very high temperatures in molten materials
Experimental research into severe nuclear accidents often requires the accurate measurement of high temperatures of molten materials. Measurements of very high temperatures (1500–2500 °C) in liquid materials using standard pyrometry can entail uncertainties in the order of 5%–10%. Pyroreflectometry is a powerful technique with the potential to significantly reduce these uncertainties. A method is proposed to optimize pyroreflectometry temperature measurements in the 1500–2500 °C range and to allow more easily the detection of the solid–liquid phase transition. The originality of this research essentially relies on the use of pyroreflectometry based on two wavelengths (1.3 and 1.55 μm) and its application to liquid materials at high temperature, which implies to adapt technological elements and metrological procedures. The proposed procedure first requires temperature calibration, which is undertaken using three eutectic fixed-point cells, reducing temperature uncertainty. Second, precise settings are adopted to enable reflectivity measurements on specular surfaces, such as the surfaces of molten metals. Pyroreflectometry measurements on liquid surfaces have been validated on an iron sample. Subsequently, the application of pyroreflectometry at very high temperatures was validated on various materials: metal (iron and 18MND5 steel), oxide (alumina), and carbide (rhenium–carbon eutectic). For each of these samples, the uncertainties of temperature measurements in the 1500–2500 °C range were estimated in the range of 1%–2%, performing well against standard pyrometry measurements. The principal difficulties encountered during the pyroreflectometry characterization were the fine-tuning of parameters (optical head orientation and lens focusing) to enable measurements on highly specular surfaces and ensuring inert interactions between the samples and the crucible.
- 1 September 2022
- Published by AIP Publishing in Review of Scientific Instruments
- Vol. 93 (9) , 094901
Pyroreflectometry as a technique for the accurate measurement of very high temperatures in molten materials
Experimental research into severe nuclear accidents often requires the accurate measurement of high temperatures of molten materials. Measurements of very high temperatures (1500–2500 °C) in liquid materials using standard pyrometry can entail uncertainties in the order of 5%–10%. Pyroreflectometry is a powerful technique with the potential to significantly reduce these uncertainties. A method is proposed to optimize pyroreflectometry temperature measurements in the 1500–2500 °C range and to allow more easily the detection of the solid–liquid phase transition. The originality of this research essentially relies on the use of pyroreflectometry based on two wavelengths (1.3 and 1.55 μm) and its application to liquid materials at high temperature, which implies to adapt technological elements and metrological procedures. The proposed procedure first requires temperature calibration, which is undertaken using three eutectic fixed-point cells, reducing temperature uncertainty. Second, precise settings are adopted to enable reflectivity measurements on specular surfaces, such as the surfaces of molten metals. Pyroreflectometry measurements on liquid surfaces have been validated on an iron sample. Subsequently, the application of pyroreflectometry at very high temperatures was validated on various materials: metal (iron and 18MND5 steel), oxide (alumina), and carbide (rhenium–carbon eutectic). For each of these samples, the uncertainties of temperature measurements in the 1500–2500 °C range were estimated in the range of 1%–2%, performing well against standard pyrometry measurements. The principal difficulties encountered during the pyroreflectometry characterization were the fine-tuning of parameters (optical head orientation and lens focusing) to enable measurements on highly specular surfaces and ensuring inert interactions between the samples and the crucible.
- 1 January 2022
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 386, 111511
Upgrading the PLINIUS platform toward smarter prototypic-corium experimental R&D
- 1 January 2022
- Published by Elsevier in Nuclear Engineering and Design
- Vol. 386, 111511
Upgrading the PLINIUS platform toward smarter prototypic-corium experimental R&D