Yazhou Dong
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yazhou Dong has a total of 46 co-authors. Here are the top co-authors by number of shared publications:
- Yaxin Zhang
University of Electronic Science and Technology of China
10 shared publications - Shixiong Liang
Tianjin University, Tianjin, China
8 shared publications - Tianchi Zhou
School of Electronic Science and Engineering, University of Electronic Science and Technology of China, Chengdu, China
6 shared publications - Huajie Liang
University of Electronic Science and Technology of China
5 shared publications - Jun Zhou
University of Electronic Science and Technology of China
5 shared publications - Ziqiang Yang
School of Electronic Science and Engineering and the Engineering Center of Integrated Optoelectronic and Radio Meta-Chips, University of Electronic Science and Technology of China, Chengdu, China
5 shared publications
Latest Publications
- Open Access
- 1 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 6 (3) , 698-710
A High-Power Frequency Doubler-Based Terahertz Frequency-Modulated Continuous-Wave Transceiver Front-End
This paper presents a high-performance terahertz frequency-modulated continuous-wave (FMCW) transceiver front-end operating at 139.5–148.5 GHz, which leverages a high-power frequency doubler to address critical challenges in terahertz amplification. A novel modular architecture is introduced to circumvent the limitations of power amplifiers (PAs), enabling a breakthrough in power handling capability. In the transmitter, a GaN Schottky diode-based doubler integrated with meta-atom resonant microstructures achieves an output power exceeding 17 dBm by enhancing electric field coupling and power conversion efficiency. The receiver employs a custom subharmonic mixer combined with a low-noise amplifier (LNA) placed adjacent to the feed source, effectively reducing the noise figure. A compact waveguide-to-microstrip transition and cavity filter assembly in the system packaging suppresses spurious emissions below −43.84 dBc. Experimental results demonstrate an input P1dB of −22.5 dBm (surpassing the −24 dBm specification), with a switchable IF bandwidth (50/90 MHz modes) for adaptive ranging. The total gain reaches 85.36 dB, and the manual gain control (MGC) accuracy achieves 0.515 dB RMS. The front-end balances power efficiency, spectral purity (phase noise ≤−92.5 dBc/Hz at 1 kHz), and linearity, providing a reliable hardware platform for high-resolution radar imaging, non-destructive testing, and real-time sensing applications.
- 1 May 2026
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Journal of Microwaves
- Vol. 6 (3) , 698-710
Open AccessA High-Power Frequency Doubler-Based Terahertz Frequency-Modulated Continuous-Wave Transceiver Front-End
This paper presents a high-performance terahertz frequency-modulated continuous-wave (FMCW) transceiver front-end operating at 139.5–148.5 GHz, which leverages a high-power frequency doubler to address critical challenges in terahertz amplification. A novel modular architecture is introduced to circumvent the limitations of power amplifiers (PAs), enabling a breakthrough in power handling capability. In the transmitter, a GaN Schottky diode-based doubler integrated with meta-atom resonant microstructures achieves an output power exceeding 17 dBm by enhancing electric field coupling and power conversion efficiency. The receiver employs a custom subharmonic mixer combined with a low-noise amplifier (LNA) placed adjacent to the feed source, effectively reducing the noise figure. A compact waveguide-to-microstrip transition and cavity filter assembly in the system packaging suppresses spurious emissions below −43.84 dBc. Experimental results demonstrate an input P1dB of −22.5 dBm (surpassing the −24 dBm specification), with a switchable IF bandwidth (50/90 MHz modes) for adaptive ranging. The total gain reaches 85.36 dB, and the manual gain control (MGC) accuracy achieves 0.515 dB RMS. The front-end balances power efficiency, spectral purity (phase noise ≤−92.5 dBc/Hz at 1 kHz), and linearity, providing a reliable hardware platform for high-resolution radar imaging, non-destructive testing, and real-time sensing applications.
- 16 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (9) , 1521-1524
High-Power-Handling GaN Terahertz High-Speed On-Chip Modulator Based on Fin-Line Double-Layer Near-Field Coupling
To address the technical challenges in the coordinated optimization of power handling, modulation rate, and system integration for traditional terahertz modulators, this paper presents a high-power-handling gallium nitride (GaN) terahertz high-speed on-chip modulator operating in the 140 GHz frequency band. The device employs a fin-line double-layer near-field coupling structure and incorporates a resonant unit cell design loaded with GaN Schottky barrier diodes (SBDs). By controlling the switching states of the diodes, dynamic switching between dual-gap resonance mode and closed-ring resonance mode is achieved, realizing a modulation depth of 20 dB and a low insertion loss of 6 dB within the 139.4-149 GHz frequency range. Furthermore, the electric field peak intensity is effectively reduced through the expansion of metal areas on both sides of the resonant unit cell gap. Combined with the high breakdown field strength (3.3 MV/cm) of GaN material, a power capacity breakthrough of 175 mW is achieved. The zero/reverse bias strategy on diodes during the modulator’s off-state suppresses thermal accumulation in conducting diodes, ensuring stable high-power operation. Experimental results demonstrate that the modulator supports 25 Gbps high-speed data transmission, providing an on-chip solution with both high power handling and high transmission rate for terahertz communication systems.
- 16 July 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (9) , 1521-1524
High-Power-Handling GaN Terahertz High-Speed On-Chip Modulator Based on Fin-Line Double-Layer Near-Field Coupling
To address the technical challenges in the coordinated optimization of power handling, modulation rate, and system integration for traditional terahertz modulators, this paper presents a high-power-handling gallium nitride (GaN) terahertz high-speed on-chip modulator operating in the 140 GHz frequency band. The device employs a fin-line double-layer near-field coupling structure and incorporates a resonant unit cell design loaded with GaN Schottky barrier diodes (SBDs). By controlling the switching states of the diodes, dynamic switching between dual-gap resonance mode and closed-ring resonance mode is achieved, realizing a modulation depth of 20 dB and a low insertion loss of 6 dB within the 139.4-149 GHz frequency range. Furthermore, the electric field peak intensity is effectively reduced through the expansion of metal areas on both sides of the resonant unit cell gap. Combined with the high breakdown field strength (3.3 MV/cm) of GaN material, a power capacity breakthrough of 175 mW is achieved. The zero/reverse bias strategy on diodes during the modulator’s off-state suppresses thermal accumulation in conducting diodes, ensuring stable high-power operation. Experimental results demonstrate that the modulator supports 25 Gbps high-speed data transmission, providing an on-chip solution with both high power handling and high transmission rate for terahertz communication systems.
- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (7) , 1063-1066
A Meta-Grating-Enhanced Terahertz Subharmonic Mixer Operating at 0.31–0.35 THz
As operating frequencies rise, traditional subharmonic mixers face significant challenges due to high conversion losses, which limit their performance in terahertz applications. To address this limitation, we propose a terahertz subharmonic mixer enhanced by a meta- grating structure. This meta-grating is strategically loaded on the backside of the substrate and integrated with the subharmonic mixing circuit. The meta-grating structure substantially enhances the electric field intensity in the mixing region, improves the coupling efficiency between the input radio frequency (RF) signal and the Schottky diodes, and increases the RF signal utilization within the mixer, ultimately reducing conversion loss. Theoretical simulations and experimental results reveal that the proposed mixer achieves a typical single-sideband conversion loss of 13 dB in the 0.31–0.35 THz range, with a minimum conversion loss of 10.5 dB, outperforming conventional designs by a margin of 2 dB. This work presents a promising solution for achieving low conversion loss in terahertz subharmonic mixers, enabling advancements in terahertz communications and sensing applications.
- 9 May 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 46 (7) , 1063-1066
A Meta-Grating-Enhanced Terahertz Subharmonic Mixer Operating at 0.31–0.35 THz
As operating frequencies rise, traditional subharmonic mixers face significant challenges due to high conversion losses, which limit their performance in terahertz applications. To address this limitation, we propose a terahertz subharmonic mixer enhanced by a meta- grating structure. This meta-grating is strategically loaded on the backside of the substrate and integrated with the subharmonic mixing circuit. The meta-grating structure substantially enhances the electric field intensity in the mixing region, improves the coupling efficiency between the input radio frequency (RF) signal and the Schottky diodes, and increases the RF signal utilization within the mixer, ultimately reducing conversion loss. Theoretical simulations and experimental results reveal that the proposed mixer achieves a typical single-sideband conversion loss of 13 dB in the 0.31–0.35 THz range, with a minimum conversion loss of 10.5 dB, outperforming conventional designs by a margin of 2 dB. This work presents a promising solution for achieving low conversion loss in terahertz subharmonic mixers, enabling advancements in terahertz communications and sensing applications.
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (8) , 4815-4827
A New Generation GaN/SiC Monolithically Integrated Frequency Sources With Ultrahigh-Power Output Based on Thermal Resistance Calculation Model
Compared with GaAs Schottky barrier diodes (SBDs), GaN SBDs offer a remarkable increase in the power capacity. However, GaN-based doublers face limitations in their continuous-wave output power due to challenges in the thermal dissipation. To address this issue, this article proposes a novel thermal resistance calculation model tailored to guide the development of devices with minimized thermal resistance and to streamline the procedure for extracting the anode temperature. This model is also suitable for a broad range of compound semiconductor processes. Based on this, the device’s thermal resistance structure was optimized, facilitated by the adoption of the GaN/SiC monolithic integration process. Subsequently, prototypes centered at 140, 170, and 220 GHz were tested. All sources represent a breakthrough in maximum output power without power synthesis technology, marking a state-of-the-art accomplishment. The measured room-temperature output power levels are as follows: 352 mW for the 140-GHz doubler, 350 mW for the 170-GHz doubler, and 109 mW for the 220-GHz doubler (higher power amplifiers are missing).
- 11 February 2025
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 73 (8) , 4815-4827
A New Generation GaN/SiC Monolithically Integrated Frequency Sources With Ultrahigh-Power Output Based on Thermal Resistance Calculation Model
Compared with GaAs Schottky barrier diodes (SBDs), GaN SBDs offer a remarkable increase in the power capacity. However, GaN-based doublers face limitations in their continuous-wave output power due to challenges in the thermal dissipation. To address this issue, this article proposes a novel thermal resistance calculation model tailored to guide the development of devices with minimized thermal resistance and to streamline the procedure for extracting the anode temperature. This model is also suitable for a broad range of compound semiconductor processes. Based on this, the device’s thermal resistance structure was optimized, facilitated by the adoption of the GaN/SiC monolithic integration process. Subsequently, prototypes centered at 140, 170, and 220 GHz were tested. All sources represent a breakthrough in maximum output power without power synthesis technology, marking a state-of-the-art accomplishment. The measured room-temperature output power levels are as follows: 352 mW for the 140-GHz doubler, 350 mW for the 170-GHz doubler, and 109 mW for the 220-GHz doubler (higher power amplifiers are missing).
- 2 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 15 (2) , 260-268
Dual-Channel Frequency Source With Distributable Channel Power Based on Mode Control
Traditional frequency multipliers typically feature single-channel input and output designs, primarily serving as local oscillators in mixers or signal sources in point-to-point transmission systems. However, these designs offer limited versatility, particularly in applications requiring dynamic power distribution across multiple directions. To address this limitation, we introduce a novel dual-channel frequency doubler based on GaAs monolithic integrated technology that allows for adjustable power distribution between two output channels. The design incorporates a vertically aligned, multi-stage waveguide that couples power into two parallel rows of diodes. By exploiting the nonlinear characteristics of these diodes, the device efficiently generates second harmonics across both channels. Moreover, the coupling ratio of input power between the two channels can be dynamically controlled by adjusting the bias applied to the diodes. Across the 155 GHz to 170 GHz frequency range, the device achieved a maximum output power of 69.9 mW and a peak conversion efficiency of 29% with both channels active. With only one channel active, the maximum output power reached 71.7 mW, and the peak conversion efficiency was 23.8%. This prototype effectively demonstrates the feasibility of our approach and establishes a solid foundation for future expansion into the terahertz frequency range
- 2 December 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Terahertz Science and Technology
- Vol. 15 (2) , 260-268
Dual-Channel Frequency Source With Distributable Channel Power Based on Mode Control
Traditional frequency multipliers typically feature single-channel input and output designs, primarily serving as local oscillators in mixers or signal sources in point-to-point transmission systems. However, these designs offer limited versatility, particularly in applications requiring dynamic power distribution across multiple directions. To address this limitation, we introduce a novel dual-channel frequency doubler based on GaAs monolithic integrated technology that allows for adjustable power distribution between two output channels. The design incorporates a vertically aligned, multi-stage waveguide that couples power into two parallel rows of diodes. By exploiting the nonlinear characteristics of these diodes, the device efficiently generates second harmonics across both channels. Moreover, the coupling ratio of input power between the two channels can be dynamically controlled by adjusting the bias applied to the diodes. Across the 155 GHz to 170 GHz frequency range, the device achieved a maximum output power of 69.9 mW and a peak conversion efficiency of 29% with both channels active. With only one channel active, the maximum output power reached 71.7 mW, and the peak conversion efficiency was 23.8%. This prototype effectively demonstrates the feasibility of our approach and establishes a solid foundation for future expansion into the terahertz frequency range
- 4 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (11) , 6518-6529
A High-Balanced Interdigital Hybrid Metallic Waveguide Coupler Based on SSPPs- Coupling for WR-4 Ultra-Full- Band Applications
Metal hybrid waveguide couplers, which are crucial passive structures in terahertz (THz) in-phase-quadrature (IQ) mixers, have raised significant attention in the development of high-speed communication systems. Spoof surface plasmon polariton (SSPP) mode, a surface wave transmission mode, possesses excellent characteristics such as localized field enhancement and energy concentration. To further expand the operating bandwidth of THz coupler and improve the balance performance between IQ paths, this article combines the SSPPs’ structure with the waveguide coupler, converts the low-pass characteristics of the traditional SSPPs’ transmission lines and high-pass rectangular waveguide transmission lines into bandpass ones, and proposes an SSPPs’ interdigital coupled quasi-periodic coupler, treating the hybrid waveguide coupler as a quasi-periodic structure, utilizing the transmission mode and dispersion relation of SSPPs to concentrate and enhance the local field strength, thus improving the coupling performance. The proposed structure achieved better amplitude balance performance and expanded the operating bandwidth. An SSPP-coupled hybrid waveguide coupler was designed and fabricated. The simulated amplitude imbalance is less than 0.3 dB and the measured one remains below 0.75 dB across the frequency range of 150–260 GHz, which has a significantly larger bandwidth than the WR-4 standard rectangular waveguide with the working frequency range of 170–260 GHz. The measured phase imbalance is within 2.2 $^{\circ}$ , and the total insertion loss is within 1.3 dB. This novel SSPPs’ coupler proves the feasibility of a promising structural design using bandpass transmission lines in replacement of traditional high-pass transmission lines in metal hybrid waveguide couplers for large-bandwidth and high-performance THz IQ mixing devices.
- 4 June 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 72 (11) , 6518-6529
A High-Balanced Interdigital Hybrid Metallic Waveguide Coupler Based on SSPPs- Coupling for WR-4 Ultra-Full- Band Applications
Metal hybrid waveguide couplers, which are crucial passive structures in terahertz (THz) in-phase-quadrature (IQ) mixers, have raised significant attention in the development of high-speed communication systems. Spoof surface plasmon polariton (SSPP) mode, a surface wave transmission mode, possesses excellent characteristics such as localized field enhancement and energy concentration. To further expand the operating bandwidth of THz coupler and improve the balance performance between IQ paths, this article combines the SSPPs’ structure with the waveguide coupler, converts the low-pass characteristics of the traditional SSPPs’ transmission lines and high-pass rectangular waveguide transmission lines into bandpass ones, and proposes an SSPPs’ interdigital coupled quasi-periodic coupler, treating the hybrid waveguide coupler as a quasi-periodic structure, utilizing the transmission mode and dispersion relation of SSPPs to concentrate and enhance the local field strength, thus improving the coupling performance. The proposed structure achieved better amplitude balance performance and expanded the operating bandwidth. An SSPP-coupled hybrid waveguide coupler was designed and fabricated. The simulated amplitude imbalance is less than 0.3 dB and the measured one remains below 0.75 dB across the frequency range of 150–260 GHz, which has a significantly larger bandwidth than the WR-4 standard rectangular waveguide with the working frequency range of 170–260 GHz. The measured phase imbalance is within 2.2 $^{\circ}$ , and the total insertion loss is within 1.3 dB. This novel SSPPs’ coupler proves the feasibility of a promising structural design using bandpass transmission lines in replacement of traditional high-pass transmission lines in metal hybrid waveguide couplers for large-bandwidth and high-performance THz IQ mixing devices.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (3) , 416-419
Terahertz Ultra Wideband High-Speed On-Chip Modulator Based on Cascade Coupling Resonance
In this letter, a terahertz ultra wideband high-speed on-chip modulator based on coupling resonance was proposed. By nesting multiple diodes in the coplanar waveguide to form multiple composite modulation units, the equivalent physical state of meta-units is controlled by external voltage signal, and then control the electromagnetic resonance characteristics of the modulation units to achieve high-speed broadband modulation of terahertz waves. This modulation mechanism simplifies the resonant structure, suppresses the parasitic parameters and improves the modulation rate of the existing terahertz external modulator. The bandwidth is expanded through cascade coupling resonance, thus realizing ultra-wideband amplitude modulation of terahertz waves transmitted in coplanar waveguides. The experimental results show that the high-speed ultra-broadband modulation of terahertz waves is achieved at 110 GHz-160 GHz with a maximum modulation depth of 15dB (97%) and a maximum modulation rate of 30 Gbps, providing a promising prospect for the development and application of the integrated terahertz direct modulation technology.
- 10 January 2024
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 45 (3) , 416-419
Terahertz Ultra Wideband High-Speed On-Chip Modulator Based on Cascade Coupling Resonance
In this letter, a terahertz ultra wideband high-speed on-chip modulator based on coupling resonance was proposed. By nesting multiple diodes in the coplanar waveguide to form multiple composite modulation units, the equivalent physical state of meta-units is controlled by external voltage signal, and then control the electromagnetic resonance characteristics of the modulation units to achieve high-speed broadband modulation of terahertz waves. This modulation mechanism simplifies the resonant structure, suppresses the parasitic parameters and improves the modulation rate of the existing terahertz external modulator. The bandwidth is expanded through cascade coupling resonance, thus realizing ultra-wideband amplitude modulation of terahertz waves transmitted in coplanar waveguides. The experimental results show that the high-speed ultra-broadband modulation of terahertz waves is achieved at 110 GHz-160 GHz with a maximum modulation depth of 15dB (97%) and a maximum modulation rate of 30 Gbps, providing a promising prospect for the development and application of the integrated terahertz direct modulation technology.
- 21 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (9) , 4565-4571
High-Efficiency GaN Frequency Doubler Based on Thermal Resistance Analysis for Continuous Wave Input
Compared to GaAs Schottky barrier diode (SBD), GaN SBD exhibits higher power handling capabilities and superior heat dissipation properties when used on high thermal conductivity SiC substrates. However, high-power continuous wave (CW) input causes a temperature rise and reduces performance in GaN-based frequency doublers. This article proposes a solution considering the thermal resistance of the SBD and using AlN as the dielectric substrate under high-power input. Furthermore, extending the metal to the ground minimizes assembly errors and guarantees consistency between simulation and experiment. The experimental results reveal the significant potential of GaN materials. With an input power of 646 mW in CW mode, a remarkable output power of 101.1 mW was achieved with only four anodes. Furthermore, at an input power of 440 mW, the frequency conversion efficiency peaked at 19% at 141 GHz. This notable achievement surpasses the performance of the existing GaN-based doublers and expands the operational capabilities to CW operation.
- 21 July 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Electron Devices
- Vol. 70 (9) , 4565-4571
High-Efficiency GaN Frequency Doubler Based on Thermal Resistance Analysis for Continuous Wave Input
Compared to GaAs Schottky barrier diode (SBD), GaN SBD exhibits higher power handling capabilities and superior heat dissipation properties when used on high thermal conductivity SiC substrates. However, high-power continuous wave (CW) input causes a temperature rise and reduces performance in GaN-based frequency doublers. This article proposes a solution considering the thermal resistance of the SBD and using AlN as the dielectric substrate under high-power input. Furthermore, extending the metal to the ground minimizes assembly errors and guarantees consistency between simulation and experiment. The experimental results reveal the significant potential of GaN materials. With an input power of 646 mW in CW mode, a remarkable output power of 101.1 mW was achieved with only four anodes. Furthermore, at an input power of 440 mW, the frequency conversion efficiency peaked at 19% at 141 GHz. This notable achievement surpasses the performance of the existing GaN-based doublers and expands the operational capabilities to CW operation.
- 29 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (10) , 4346-4356
A Sub-Terahertz High-Speed Traveling-Wave Switch Modulator Based on Dynamically Tunable Double-Resonant Coupling Units
High-speed direct modulation devices are of great significance for the development of high-speed communication systems with large bandwidth, miniaturization, and low complexity. However, an increase in the carrier frequency in the sub-terahertz band and above will negatively impact high-performance direct modulation devices due to the large insertion loss and low on–off ratio. Based on the traveling-wave modulation mechanism, this article adopts the zero-phase-difference amplitude modulator design method. More specifically, a 1- $\mu$ m small anode Schottky diode is combined with a Z-type matching structure to form a dual-resonant coupling dynamic tunable unit. Interunit coupling is found to further improve the on–off ratio. In this way, high-speed dynamic modulation is performed for the transmission traveling-wave amplitude with low insertion loss and a high on–off ratio. On this basis, a 0.14-THz on–off keying (OOK) high-speed traveling-wave modulator is proposed, and our results showed that a on–off ratio of 25.4 dB could be achieved at the zero-phase-difference point by only using two dynamic structural units. Meanwhile, the control voltage could be adjusted to achieve high-speed modulation with a phase difference of only 3.66 $^\circ$ during the entire control voltage transition, a data rate of 24 Gb/s, and 33.99% sidebands occupation.
- 29 March 2023
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Transactions on Microwave Theory and Techniques
- Vol. 71 (10) , 4346-4356
A Sub-Terahertz High-Speed Traveling-Wave Switch Modulator Based on Dynamically Tunable Double-Resonant Coupling Units
High-speed direct modulation devices are of great significance for the development of high-speed communication systems with large bandwidth, miniaturization, and low complexity. However, an increase in the carrier frequency in the sub-terahertz band and above will negatively impact high-performance direct modulation devices due to the large insertion loss and low on–off ratio. Based on the traveling-wave modulation mechanism, this article adopts the zero-phase-difference amplitude modulator design method. More specifically, a 1- $\mu$ m small anode Schottky diode is combined with a Z-type matching structure to form a dual-resonant coupling dynamic tunable unit. Interunit coupling is found to further improve the on–off ratio. In this way, high-speed dynamic modulation is performed for the transmission traveling-wave amplitude with low insertion loss and a high on–off ratio. On this basis, a 0.14-THz on–off keying (OOK) high-speed traveling-wave modulator is proposed, and our results showed that a on–off ratio of 25.4 dB could be achieved at the zero-phase-difference point by only using two dynamic structural units. Meanwhile, the control voltage could be adjusted to achieve high-speed modulation with a phase difference of only 3.66 $^\circ$ during the entire control voltage transition, a data rate of 24 Gb/s, and 33.99% sidebands occupation.
- 15 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (11) , 1830-1833
A Meta-Structure-Based Frequency Doubler With Low Input Power
As the operating frequency increases, the output power of traditional frequency doublers becomes too low to drive the next stage devices. To address this problem, a double-layer meta-chip circuit consisting of a symmetrical split ring (SSR) structure with a doubler circuit is presented. It combines the transmission mode in the rectangular waveguide with the resonance mode in the meta structure. The meta structure improves the coupling efficiency between the diode and electromagnetic energy, strengthens the electric field at the diode, and ultimately enhances the efficiency of the frequency doubler at low input power. From 160–180 GHz, the experiments show that the frequency doubler with SSR achieved a peak efficiency of 22.4% with an output power of 10.6 mW. Its performance of maximum output power is 45.2% better than the traditional structure, which provides an important technical approach to achieve higher efficiency at low input power.
- 15 September 2022
- Published by Institute of Electrical and Electronics Engineers (IEEE) in IEEE Electron Device Letters
- Vol. 43 (11) , 1830-1833
A Meta-Structure-Based Frequency Doubler With Low Input Power
As the operating frequency increases, the output power of traditional frequency doublers becomes too low to drive the next stage devices. To address this problem, a double-layer meta-chip circuit consisting of a symmetrical split ring (SSR) structure with a doubler circuit is presented. It combines the transmission mode in the rectangular waveguide with the resonance mode in the meta structure. The meta structure improves the coupling efficiency between the diode and electromagnetic energy, strengthens the electric field at the diode, and ultimately enhances the efficiency of the frequency doubler at low input power. From 160–180 GHz, the experiments show that the frequency doubler with SSR achieved a peak efficiency of 22.4% with an output power of 10.6 mW. Its performance of maximum output power is 45.2% better than the traditional structure, which provides an important technical approach to achieve higher efficiency at low input power.