Arjen Deetman
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Arjen Deetman has a total of 14 co-authors. Here are the top co-authors by number of shared publications:
- Derk Bos
Eindhoven University of Technology
4 shared publications - Rob Wolfs
Department of the Built Environment Eindhoven University of Technology Eindhoven The Netherlands
3 shared publications - Sandra S. Lucas
Department of the Built Environment, Eindhoven University of Technology, Eindhoven, The Netherlands
2 shared publications Theo Salet
2 shared publicationsA.S.J. Suiker
1 shared publicationAlexander Stefas
Kraenk Visuell GbR
1 shared publication
Latest Publications
- 28 June 2026
- Published by Springer Nature
- p. 139-146
Towards On-Line and In-Line Quality Control in Digital Fabrication with Concrete
- 28 June 2026
- Published by Springer Nature
- p. 139-146
Towards On-Line and In-Line Quality Control in Digital Fabrication with Concrete
- 1 April 2026
- Published by Springer Nature
- p. 26-34
Correlating In-line Sensor Data to Hardened State Material Properties in Digital Fabrication with Concrete
- 1 April 2026
- Published by Springer Nature
- p. 26-34
Correlating In-line Sensor Data to Hardened State Material Properties in Digital Fabrication with Concrete
- Open Access
- 26 December 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 310
Characterization of early-age elastic–plastic properties of 3D printed materials using indentation testing
- 26 December 2025
- Published by Elsevier in International Journal of Mechanical Sciences
- Vol. 310
Open AccessCharacterization of early-age elastic–plastic properties of 3D printed materials using indentation testing
- Open Access
- 12 December 2025
- Published by Elsevier in Results in Engineering
- Vol. 29
A database framework for 3D concrete printing
- 12 December 2025
- Published by Elsevier in Results in Engineering
- Vol. 29
Open AccessA database framework for 3D concrete printing
- Open Access
- 17 May 2024
- Published by Springer Nature in Materials and Structures
- Vol. 57 (5) , 1-18
An in-line dye tracer experiment to measure the residence time in continuous concrete processing
This paper introduces an in-line dye tracer experiment to measure the residence time functions in continuous concrete processing. These functions quantify the material-system interdependency and can be used to compare different material-system combinations and for quality and process control. A Rhodamine B solution was used as the tracer material and detected by measuring the color intensity using a digital image processing technique. The experiment was validated on a 3D concrete printing system by comparing the results of impulse, step-up and step-down inputs with different tracer quantities. The results show that a high signal-to-noise ratio can be obtained with low tracer concentrations. For the examined combination of material and system, an impact on the original process was only observed for the step-up inputs at high tracer quantities. It is concluded that the presented method is cost-effective and non-labor-intensive and, therefore, has the potential for wide adoption and integration in automated workflows.
- 17 May 2024
- Published by Springer Nature in Materials and Structures
- Vol. 57 (5) , 1-18
Open AccessAn in-line dye tracer experiment to measure the residence time in continuous concrete processing
This paper introduces an in-line dye tracer experiment to measure the residence time functions in continuous concrete processing. These functions quantify the material-system interdependency and can be used to compare different material-system combinations and for quality and process control. A Rhodamine B solution was used as the tracer material and detected by measuring the color intensity using a digital image processing technique. The experiment was validated on a 3D concrete printing system by comparing the results of impulse, step-up and step-down inputs with different tracer quantities. The results show that a high signal-to-noise ratio can be obtained with low tracer concentrations. For the examined combination of material and system, an impact on the original process was only observed for the step-up inputs at high tracer quantities. It is concluded that the presented method is cost-effective and non-labor-intensive and, therefore, has the potential for wide adoption and integration in automated workflows.
- 18 September 2022
- Published by Springer Nature
- p. 96-107
An Open Approach to Robotic Prototyping for Architectural Design and Construction
- 18 September 2022
- Published by Springer Nature
- p. 96-107
An Open Approach to Robotic Prototyping for Architectural Design and Construction