Yi-Feng Su
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Yi-Feng Su has a total of 29 co-authors. Here are the top co-authors by number of shared publications:
- Jiheon Jun
Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, USA
7 shared publications - John E. Wade
Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831, USA
5 shared publications - Dino Sulejmanovic
Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831, USA
3 shared publications - Gyoung Gug Jang
ORNL
3 shared publications - Jack R. Ferrell
National Renewable Energy Laboratory, 15013 Denver W Pkwy, Golden, CO 80401, USA
2 shared publications - James R. Keiser
Materials Science and Technology Division, Oak Ridge National Laboratory, Oak Ridge, TN 37831, USA
2 shared publications
Latest Publications
- 30 September 2024
- Published by Springer Nature in JOM
- Vol. 77 (5) , 2735-2742
Investigation of Chemical Species in the Corrosion Barrier Layer on Thermal CO2 Treated AZ91D Magnesium Alloy with Lithium Nitrate
- 30 September 2024
- Published by Springer Nature in JOM
- Vol. 77 (5) , 2735-2742
Investigation of Chemical Species in the Corrosion Barrier Layer on Thermal CO2 Treated AZ91D Magnesium Alloy with Lithium Nitrate
- Open Access
Cost-Effective Thermomechanical Processing of Nanostructured Ferritic Alloys: Microstructure and Mechanical Properties Investigation
Nanostructured ferritic alloys (NFAs), such as oxide-dispersion strengthened (ODS) alloys, play a vital role in advanced fission and fusion reactors, offering superior properties when incorporating nanoparticles under irradiation. Despite their importance, the high cost of mass-producing NFAs through mechanical milling presents a challenge. This study delves into the microstructure-mechanical property correlations of three NFAs produced using a novel, cost-effective approach combining severe plastic deformation (SPD) with the continuous thermomechanical processing (CTMP) method. Analysis using scanning electron microscopy (SEM)-electron backscatter diffraction (EBSD) revealed nano-grain structures and phases, while scanning transmission electron microscopy (STEM)-energy dispersive X-ray spectroscopy (EDS) quantified the size and density of Ti-N, Y-O, and Cr-O fine particles. Atom probe tomography (APT) further confirmed the absence of finer Y-O particles and characterized the chemical composition of the particles, suggesting possible nitride dispersion strengthening. Correlation of microstructure and mechanical testing results revealed that CTMP alloys, despite having lower nanoparticle densities, exhibit strength and ductility comparable to mechanically milled ODS alloys, likely due to their fine grain structure. However, higher nanoparticle densities may be necessary to prevent cavity swelling under high-temperature irradiation and helium gas production. Further enhancements in uniform nanoparticle distribution and increased sink strength are recommended to mitigate cavity swelling, advancing their suitability for nuclear applications.
Open AccessCost-Effective Thermomechanical Processing of Nanostructured Ferritic Alloys: Microstructure and Mechanical Properties Investigation
Nanostructured ferritic alloys (NFAs), such as oxide-dispersion strengthened (ODS) alloys, play a vital role in advanced fission and fusion reactors, offering superior properties when incorporating nanoparticles under irradiation. Despite their importance, the high cost of mass-producing NFAs through mechanical milling presents a challenge. This study delves into the microstructure-mechanical property correlations of three NFAs produced using a novel, cost-effective approach combining severe plastic deformation (SPD) with the continuous thermomechanical processing (CTMP) method. Analysis using scanning electron microscopy (SEM)-electron backscatter diffraction (EBSD) revealed nano-grain structures and phases, while scanning transmission electron microscopy (STEM)-energy dispersive X-ray spectroscopy (EDS) quantified the size and density of Ti-N, Y-O, and Cr-O fine particles. Atom probe tomography (APT) further confirmed the absence of finer Y-O particles and characterized the chemical composition of the particles, suggesting possible nitride dispersion strengthening. Correlation of microstructure and mechanical testing results revealed that CTMP alloys, despite having lower nanoparticle densities, exhibit strength and ductility comparable to mechanically milled ODS alloys, likely due to their fine grain structure. However, higher nanoparticle densities may be necessary to prevent cavity swelling under high-temperature irradiation and helium gas production. Further enhancements in uniform nanoparticle distribution and increased sink strength are recommended to mitigate cavity swelling, advancing their suitability for nuclear applications.
- Open Access
- 28 May 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (25) , 17696-17709
Lithium nitrate salt-assisted CO2 absorption for the formation of corrosion barrier layer on AZ91D magnesium alloy
The formation of Mg–Li–C–O barrier layer on AZ91D Mg alloy using LiNO3-assisted thermal CO2 treatment provides a pathway to utilize excessive CO2 for corrosion protection of AZ91D.
- 28 May 2024
- Published by Royal Society of Chemistry (RSC) in RSC Advances
- Vol. 14 (25) , 17696-17709
Open AccessLithium nitrate salt-assisted CO2 absorption for the formation of corrosion barrier layer on AZ91D magnesium alloy
The formation of Mg–Li–C–O barrier layer on AZ91D Mg alloy using LiNO3-assisted thermal CO2 treatment provides a pathway to utilize excessive CO2 for corrosion protection of AZ91D.
- 30 January 2024
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 21 (3) , 1097-1111
Open-air plasma-assisted deposition of organosilicon coating for corrosion protection of AZ91D Mg alloy
- 30 January 2024
- Published by Springer Nature in Journal of Coatings Technology and Research
- Vol. 21 (3) , 1097-1111
Open-air plasma-assisted deposition of organosilicon coating for corrosion protection of AZ91D Mg alloy
- 4 January 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (6) , 1-52
Leveraging Additive Manufacturing to Fabricate High Temperature Alloys With Co-Designed Mechanical Properties and Environmental Resistance
A paradigm shift in the traditional sequential design approaches is critically essential to create application-specific hierarchical and multifunctional materials with superior long-term performance for next-generation energy technologies involving extreme environments. In the current work, we aim to leverage the flexibility and geometric/compositional complexity offered by additive manufacturing to demonstrate this new approach by codesigning a compositionally graded Ni-based alloy for molten salts\sCO2 heat exchangers to enable mitigation of environmental degradation of surfaces exposed to molten halide salts, while simultaneously suppressing the consequent deterioration in mechanical stability. Thermokinetic modeling describing the underlying physics of thermally- and environmentally induced spatiotemporal compositional and microstructural evolution will be employed to predict the parameter space of material deposition processes and precisely identify the required composition gradient. Preliminary corrosion and mechanical testing of the dual material demonstrated the potential of the material to replace existing solid solution strengthened materials for this application.
- 4 January 2024
- Published by ASME International in Journal of Engineering for Gas Turbines and Power
- Vol. 146 (6) , 1-52
Leveraging Additive Manufacturing to Fabricate High Temperature Alloys With Co-Designed Mechanical Properties and Environmental Resistance
A paradigm shift in the traditional sequential design approaches is critically essential to create application-specific hierarchical and multifunctional materials with superior long-term performance for next-generation energy technologies involving extreme environments. In the current work, we aim to leverage the flexibility and geometric/compositional complexity offered by additive manufacturing to demonstrate this new approach by codesigning a compositionally graded Ni-based alloy for molten salts\sCO2 heat exchangers to enable mitigation of environmental degradation of surfaces exposed to molten halide salts, while simultaneously suppressing the consequent deterioration in mechanical stability. Thermokinetic modeling describing the underlying physics of thermally- and environmentally induced spatiotemporal compositional and microstructural evolution will be employed to predict the parameter space of material deposition processes and precisely identify the required composition gradient. Preliminary corrosion and mechanical testing of the dual material demonstrated the potential of the material to replace existing solid solution strengthened materials for this application.
- Open Access
Characterization and Electrochemical Analysis of Acidic Condensate-Induced Corrosion on Aluminized Coating on Steel in Residential Heaters
Condensing furnace residential heaters are starting to replace outdated and less efficient non-condensing units in homes across the US. However, the burning of natural gas in these new units produces acidic gases, which can form acid droplets (H2SO4, HNO3, H2CO3, etc.) that are corrosive to low-grade heat exchanger metallic materials. Type-1 aluminized steel has been used in industrial applications, such as marine, heating, and automobile parts, due to its resistance to oxidation at elevated temperature. Many components of the condensing furnaces, including heat exchangers, are made from type-1 aluminized steel. We investigated the interaction of type-1 aluminized steel substrates with two acidic condensate liquids by 500 h corrosion exposures as well as short-term electrochemical impedance measurements. SEM plan and cross-sectional view images revealed damage to the Al-Si rich layer and exposure of the steel substrate. The non-uniform damage in the Al-Si rich layer was likely attributed to a pitting corrosion mechanism and induced by high acidity of the condensate liquid. Electrochemical impedance measurements in an acidic condensate revealed lower corrosion resistance of the aluminized steel surface with a weld line, identifying welded sections as preferential corrosion initiation sites.
Open AccessCharacterization and Electrochemical Analysis of Acidic Condensate-Induced Corrosion on Aluminized Coating on Steel in Residential Heaters
Condensing furnace residential heaters are starting to replace outdated and less efficient non-condensing units in homes across the US. However, the burning of natural gas in these new units produces acidic gases, which can form acid droplets (H2SO4, HNO3, H2CO3, etc.) that are corrosive to low-grade heat exchanger metallic materials. Type-1 aluminized steel has been used in industrial applications, such as marine, heating, and automobile parts, due to its resistance to oxidation at elevated temperature. Many components of the condensing furnaces, including heat exchangers, are made from type-1 aluminized steel. We investigated the interaction of type-1 aluminized steel substrates with two acidic condensate liquids by 500 h corrosion exposures as well as short-term electrochemical impedance measurements. SEM plan and cross-sectional view images revealed damage to the Al-Si rich layer and exposure of the steel substrate. The non-uniform damage in the Al-Si rich layer was likely attributed to a pitting corrosion mechanism and induced by high acidity of the condensate liquid. Electrochemical impedance measurements in an acidic condensate revealed lower corrosion resistance of the aluminized steel surface with a weld line, identifying welded sections as preferential corrosion initiation sites.
- Open Access
Atmospheric Pressure Plasma Treatment of Magnesium Alloy for Enhanced Coating Adhesion and Corrosion Resistance
Atmospheric pressure plasma (AP) treatment, using an open-air jet of ionized CO2, N2, or air, was applied to AZ91D Mg alloy surfaces to investigate its effects on primer coating adhesion and corrosion resistance. The CO2 and air AP treatments formed an O- and C-rich surface layer (Mg-O-C) consisting of agglomerated nanoparticles and pits with a depth of a few microns and increasing the surface roughness by 6–8 times compared with the reference 600 grit-finished surface. Then, three commercial primers, zinc phosphate (ZnP), chromate-containing epoxy, and MIL23377, were applied on the treated surfaces to evaluate the corrosion resistance associated with the coating adhesion. Microscopic analysis demonstrated stronger interlocking between the primer layer and the nano-/microrough Mg-O-C surface compared to the untreated (600 grit-finished) surfaces, indicating improved coating adhesion and corrosion resistance. Crosscut tests of the MIL23377 primer on the CO2 and air AP-treated surfaces showed the highest level of adhesion, ASTM class 5B. Salt spray corrosion tests showed that after 8 days of exposure, the primer coatings on air AP-treated surfaces had corrosion areas that were more than four times smaller than that of the 600 grit-finished surface. The N2 AP treatment showed similar adhesion enhancement. The preliminary operation expenses for AP treatment using CO2, N2, and air were estimated at USD 30.62, USD 35.45, and USD 29.75 (from an air cylinder)/USD 0.66 (from an air compressor) per m2, respectively.
Open AccessAtmospheric Pressure Plasma Treatment of Magnesium Alloy for Enhanced Coating Adhesion and Corrosion Resistance
Atmospheric pressure plasma (AP) treatment, using an open-air jet of ionized CO2, N2, or air, was applied to AZ91D Mg alloy surfaces to investigate its effects on primer coating adhesion and corrosion resistance. The CO2 and air AP treatments formed an O- and C-rich surface layer (Mg-O-C) consisting of agglomerated nanoparticles and pits with a depth of a few microns and increasing the surface roughness by 6–8 times compared with the reference 600 grit-finished surface. Then, three commercial primers, zinc phosphate (ZnP), chromate-containing epoxy, and MIL23377, were applied on the treated surfaces to evaluate the corrosion resistance associated with the coating adhesion. Microscopic analysis demonstrated stronger interlocking between the primer layer and the nano-/microrough Mg-O-C surface compared to the untreated (600 grit-finished) surfaces, indicating improved coating adhesion and corrosion resistance. Crosscut tests of the MIL23377 primer on the CO2 and air AP-treated surfaces showed the highest level of adhesion, ASTM class 5B. Salt spray corrosion tests showed that after 8 days of exposure, the primer coatings on air AP-treated surfaces had corrosion areas that were more than four times smaller than that of the 600 grit-finished surface. The N2 AP treatment showed similar adhesion enhancement. The preliminary operation expenses for AP treatment using CO2, N2, and air were estimated at USD 30.62, USD 35.45, and USD 29.75 (from an air cylinder)/USD 0.66 (from an air compressor) per m2, respectively.
- Open Access
- 20 December 2022
- Published by MDPI AG in Sustainability
- Vol. 15 (1) , 22
Corrosion Compatibility of Stainless Steels and Nickel in Pyrolysis Biomass-Derived Oil at Elevated Storage Temperatures
Corrosion compatibility of stainless steels and nickel (Ni200) was assessed in fast pyrolysis bio-oil produced from pyrolysis of high ash and high moisture forest residue biomass. Sample mass change, ICP-MS and post-exposure electron microscopy characterization was used to investigate the extent of corrosion. Among the tested samples, type 430F and type 316 stainless steels (SS430F and SS316) and Ni200 (~98.5% Ni) showed minimal mass changes (less than 2 mg∙cm−2) after the bio-oil exposures at 50 and 80 °C for up to 168 h. SS304 was also considered to be compatible in the bio-oil due to its relatively low mass change (1.6 mg∙cm−2 or lower). SS410 samples showed greater mass loss values even after exposures at a relatively low temperature of 35 °C. Fe/Cr values from ICP-MS data implied that Cr enrichment in stainless steels would result in a protective oxide layer associated with corrosion resistance against the bio-oil. Post exposure characterization showed continuous and uniform Cr distribution in the surface oxide layer of SS430F, which showed a minimal mass change, but no oxide layer on a SS430 sample, which exhibited a significant mass loss.
- 20 December 2022
- Published by MDPI AG in Sustainability
- Vol. 15 (1) , 22
Open AccessCorrosion Compatibility of Stainless Steels and Nickel in Pyrolysis Biomass-Derived Oil at Elevated Storage Temperatures
Corrosion compatibility of stainless steels and nickel (Ni200) was assessed in fast pyrolysis bio-oil produced from pyrolysis of high ash and high moisture forest residue biomass. Sample mass change, ICP-MS and post-exposure electron microscopy characterization was used to investigate the extent of corrosion. Among the tested samples, type 430F and type 316 stainless steels (SS430F and SS316) and Ni200 (~98.5% Ni) showed minimal mass changes (less than 2 mg∙cm−2) after the bio-oil exposures at 50 and 80 °C for up to 168 h. SS304 was also considered to be compatible in the bio-oil due to its relatively low mass change (1.6 mg∙cm−2 or lower). SS410 samples showed greater mass loss values even after exposures at a relatively low temperature of 35 °C. Fe/Cr values from ICP-MS data implied that Cr enrichment in stainless steels would result in a protective oxide layer associated with corrosion resistance against the bio-oil. Post exposure characterization showed continuous and uniform Cr distribution in the surface oxide layer of SS430F, which showed a minimal mass change, but no oxide layer on a SS430 sample, which exhibited a significant mass loss.
- Open Access
- 19 September 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (18) , 11743
Effect of Carboxylic Acids on Corrosion of Type 410 Stainless Steel in Pyrolysis Bio-Oil
Biomass-derived oils are renewable fuel sources and commodity products and are proposed to partially or entirely replace fossil fuels in sectors generally considered difficult to decarbonize such as aviation and maritime propulsion. Bio-oils contain a range of organic compounds with varying functional groups which can lead to polarity-driven phase separation and corrosion of containment materials during processing and storage. Polar compounds, such as organic acids and other oxygenates, are abundant in bio-oils and are considered corrosive to structural alloys, particularly to those with a low-Cr content. To study the corrosion effects of small carboxylic acids present in pyrolysis bio-oils, type 410 stainless steel (SS410) specimens were exposed in bio-oils with varying formic, acetic, propionic and hexanoic acid contents at 50 °C during 48 h exposures. The specific mass change data show a linear increase in mass loss with increasing formic acid concentration. Interestingly, a mild corrosion inhibition effect on the corrosion of SS410 specimens was observed with the addition of acetic, propionic and hexanoic acids in the bio-oil.
- 19 September 2022
- Published by MDPI AG in Sustainability
- Vol. 14 (18) , 11743
Open AccessEffect of Carboxylic Acids on Corrosion of Type 410 Stainless Steel in Pyrolysis Bio-Oil
Biomass-derived oils are renewable fuel sources and commodity products and are proposed to partially or entirely replace fossil fuels in sectors generally considered difficult to decarbonize such as aviation and maritime propulsion. Bio-oils contain a range of organic compounds with varying functional groups which can lead to polarity-driven phase separation and corrosion of containment materials during processing and storage. Polar compounds, such as organic acids and other oxygenates, are abundant in bio-oils and are considered corrosive to structural alloys, particularly to those with a low-Cr content. To study the corrosion effects of small carboxylic acids present in pyrolysis bio-oils, type 410 stainless steel (SS410) specimens were exposed in bio-oils with varying formic, acetic, propionic and hexanoic acid contents at 50 °C during 48 h exposures. The specific mass change data show a linear increase in mass loss with increasing formic acid concentration. Interestingly, a mild corrosion inhibition effect on the corrosion of SS410 specimens was observed with the addition of acetic, propionic and hexanoic acids in the bio-oil.