Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Sakhob Khumkoa has a total of 39 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    Baseline techno-economic and life cycle assessment of black mass production

    by Tanongsak Yingnakorn, Chatisa Kansomket, Chaiyasit Longbutsri, Sean Scott, Tapany Patcharawit, Jake M. Yang, Andrew P. Abbott, Sakhob Khumkoa

  • Open Access

    Thermal–Physical Pretreatment and Extraction of Indium from LCD Waste Stream

    by Napat Mahiwan, Chatisa Kansomket, Sumita Chailoi, Natthicha Ma-Ud, Sakhob Khumkoa, Teerawut Tunnukij, Tapany Patcharawit

    Liquid Crystal Display (LCD) waste from various sources, such as TVs, desktop monitors, and computer notebooks, is increasing and has become an environmental issue, requiring legalized disposal and practical recycling technologies to address it. LCD screens generally contain Indium–Tin–Oxide (ITO), which are critical and valuable metals worth recovering. The aim of this research is to optimize the thermal–physical pretreatment of LCD screens after dismantling to effectively recover indium via leaching and solvent extraction at an acceptable recovery rate. A comparative study was conducted on the recovery of indium from LCD waste from TVs and a mixed waste stream, where the latter source represents the total proportion of LCD waste accumulation. This comparison aimed to identify key factors for effective recovery from TV and mixed waste streams, containing lower and higher amounts of indium, respectively. The recovery process consisted of waste pretreatment, leaching, and solvent extraction. In the first pretreatment, ethanol immersion was found to be the most practical for polarizing film removal for both streams in comparison with manual peeling, water immersion, surface heating, and calcination. Comminution in the second pretreatment aimed to increase the surface area for the subsequent chemical reaction. For both streams, HCl leaching allowed effective indium recovery of >99.9% at the optimal conditions of 5 M HCl with 10% H2O2 addition and an S/L ratio of 500 g/L under ultrasonication for 1 h. Subsequent purification via solvent extraction was conducted to exclude iron as the key impurity. In solvent extraction, D2EHPA concentration, pH, and the organic-to-aqueous ratio (O:A) was investigated. Optimal solvent extraction was achieved using 0.25 M D2EHPA at pH 1 and an O/A ratio of 1:5 for 5 min, while ascorbic acid was added to eliminate undesirable iron. Although both waste streams achieved >99.9% leaching efficiency, they exhibited different extraction behaviors after scrubbing and stripping. The TV waste stream achieved 74.32% solvent extraction efficiency. The higher indium recovery of 84.34% via solvent extraction through the stripping of the mixed stream might be due to the higher initial indium concentration reacting with D2EHPA. This led to the overall recovery of the two waste streams as 70.22% and 80.24% for TV and mixed waste streams, respectively, possibly due to higher amounts of indium in the initial waste stream. The findings of this study serve as research and practical guidance for indium recovery and EOL–LCD recycling.


  • Open Access

    Solvent extraction recovery of critical metals: A comparative study using black mass and separated cathode material from spent Li-ion batteries

    by Chatisa Kansomket, Tanongsak Yingnakorn, Chaiyasit Longbutsri, Thanapon Chandakhiaw, Tapany Patcharawit, Sakhob Khumkoa

  • Open Access

    Silver Purification from Waste for Bio–Sonochemical Synthesis of Ag2O Nanoparticles Using Cannabis sativa Flower Extract

    by Sumita Chailoi, Napat Mahiwan, Chatisa Kansomket, Thanapon Chandakhiaw, Tapany Patcharawit, Tanakorn Uthaiphetra, Kiattisak Batsungnoen, Sakhob Khumkoa

    Rapidly increasing manufacturing waste intensifies the need for highly efficient and economically feasible waste-to-resource technologies. This research presented an upcycling strategy that transforms silver (Ag)-bearing waste into functional silver oxide nanoparticles (Ag2O NPs) for potential use in biomedical applications. A two-step process of silver purification and the bio–sonochemical synthesis of Ag2O NPs was employed. First, the sequential purification of Ag via melt-refining and electrorefining was utilized to efficiently achieve a silver purity of ≥99.90%. This purification encouraged the recycling of various forms of Ag-bearing waste. Subsequently, the purified Ag was prepared as the precursor for the bio–sonochemical synthesis of Ag2O NPs, using Cannabis sativa SUT CBD12 flower extract as a natural reducing agent. The optimal conditions were adapted from a preliminary test using AgNO3 as the precursor. At initial concentrations of 0.01 M Ag solution, 1 mM PVP solution, and 10 g dried weight of Cannabis sativa SUT CBD12 added to 100 mL DI water, the optimal condition was obtained at the capping agent:reducing agent:precursor volume ratio of 0.6:0.006:1, pH 10–12, under a short sonication time of 2 min. The purified Ag (waste-derived) and AgNO3-derived Ag2O NPs shared similar spherical shapes and sizes of ~100–130 nm. The Ag2O NPs showed antibacterial effectiveness against S. aureus (ZOI of 26–29 mm) and E. coli (ZOI of 16–20 mm). Preliminary observations into the incorporation of Ag2O NPs into polycaprolactone (PCL) to produce electrospun PCL/Ag2O NPs nano fabrics shows a bead-free morphology, raising the possibility of a potential use in wound dressing. Following these preliminary explorations into potential uses and emission controls, a circular design maximizing the use of recycled resources is emphasized.

  • Top Cited Papers
    Open Access

    Hydrothermal synthesis of ZnO nanoparticles from recycled ZnO obtained from electric arc furnace dust: morphology control and applications

    by Sirunya Somla, Tanongsak Yingnakorn, Thanapon Chandakhiaw, Chaiyasit Longbutsri, Loeslakkhana Sriklang, Sakhob Khumkoa

    This study presents a sustainable, value-added approach to synthesizing high-quality zinc oxide nanoparticles (ZnO NPs) by utilizing ZnO recovered from industrial electric arc furnace dust (EAFD) waste. The integrated two-stage process involved selective acid leaching for precursor purification, followed by hydrothermal synthesis for morphology control. Optimized leaching using 2 M H2SO4 achieved a high zinc recovery rate of over 90% while effectively minimizing lead contamination. Subsequently, key hydrothermal parameters—including pH (7–12), temperature 100–200 °C, reaction time (1–24 h), and NaOH concentration (0.5–6 M)—were systematically varied. This optimization successfully produced ZnO NPs with diverse, tunable morphologies, including nanorods, nanoplates, and nanogranules. XRD confirmed the high crystallinity and phase purity (wurtzite structure), and UV-Visible spectroscopy showed a strong UV absorption with a calculated band gap of 3.34 eV. The antibacterial activity revealed that the nanoplate morphology produced a larger inhibition zone than the nanorod against both Staphylococcus aureus and Escherichia coli. These findings demonstrate the viability of upcycling industrial waste into high-performance, morphology-controlled nanomaterials, paving the way for sustainable and environmentally friendly production.


  • Open Access

    Hydrometallurgical valorization of strontium ferrite magnet sludge for the selective production of high-purity hematite (α-Fe2O3) and strontium carbonate (SrCO3)

    by Chaiyasit Longbutsri, Tanongsak Yingnakorn, Thanapon Chandakhiaw, Chatisa Kansomket, Sirunya Somla, Natthicha Ma-Ud, Muwafaq A. Rabeea, Tapany Patcharawit, Sakhob Khumkoa

  • Open Access

    Upcycling of Cupric Chloride Waste Solution from PCB Manufacturing for Antibacterial Copper Nanoparticles

    by Tapany Patcharawit, Chatisa Kansomket, Napat Mahiwan, Sumita Chailoi, Thanapon Chandakhiaw, Tanongsak Yingnakorn, Teerawut Tunnukij, Sakhob Khumkoa

    Issues encompassing hazardous waste management face challenges, particularly those involving the manufacture of electronic devices such as PCBs that are in high demand with continual growth. Therefore, upcycling to create new products viable for highly valued markets emphasizes alternative solutions towards the circular economy. This research highlights the advantages of copper sulfate recovery from the cupric chloride etching waste solution from PCB manufacturing, combined with the synthesis of copper nanoparticles for antibacterial application. First, aluminium cementation, sulfuric acid leaching, and crystallization were incorporated in the recovery step to ensure a high purity of 99.95% and a recovery of 94.76%. Aluminium cementation selectively offered copper-containing precipitates suitable for leaching to gain high-purity recovered products. In the second step, copper nanoparticles were synthesized using 0.01–0.20 M copper sulfate precursors via sonochemical reduction. In total, 1–5 mL of hydrazine and 5–30 mL of 0.01 M ethylene glycol were added into a 50 mL precursor as reducing and capping agents, respectively. Hydrazine addition under high pH played a key role in controlling the shape, size, and purity of the copper nanoparticles, required for their antibacterial properties. The optimum condition gave spherical or polygonal copper nanoparticles of 54.54 nm at 99.95% purity and >92% recovery. The antibacterial test of the synthesized copper nanoparticles using E. coli via agar well diffusion exhibited a zone of inhibition (ZOI) of 50 mm at 127 mg/mL, similar to the antibiotic-controlled condition, proving their antibacterial potential. Along with process effectiveness, a feasibility study of the inventing process confirmed the environmental and economic impacts of minimizing energy consumption and processing time, which are competitive with respect to the existing recycling technologies.


  • Open Access

    Tin oxide nanoparticle extraction from waste solder dross via low-temperature hydrometallurgical process

    by Tanongsak Yingnakorn, Sirunya Somla, Thanapon Chandakhiaw, Ethan Cheung, Sakhob Khumkoa

    This study proposes a hydrometallurgical approach to valorising industrial waste by producing SnO2 nanoparticles (NPs) from waste solder dross obtained by skimming off of tin solder baths from electronic dipping processes. The process involves leaching the dross with aqueous hydrochloric acid solution and hydrogen peroxide, followed by precipitation with ammonium hydroxide and purification with aqueous nitric acid solution. The optimised leaching conditions were determined to be 4 mol∙ L‒1 HCl, 11% v/v H2O2, 25℃, and a leaching time of 15 min. SnO2 NPs were successfully precipitated at pH 4 using 25% v/v NH4OH and purified with 1 mol∙ L‒1 HNO3. The whole process was able to recover nearly 100% of tin from waste solder dross as SnO2 NPs, with a high purity of 99.5% and a particle size distribution of ca. 2 nm to 7 nm. The overall material balance and the simple cost of the process were evaluated to provide an idea of the economic viability and the possibility of scaling up the method detailed in this work.

  • Open Access

    Machine Learning–Based Prediction of Complex Combination Phases in High-Entropy Alloys

    by Jirapracha Thampiriyanon, Sakhob Khumkoa

    High-entropy alloys (HEAs) are a novel class of materials that exhibit exceptional mechanical, thermal and corrosion-resistant properties, making them highly promising for various industrial applications. The complex and variable compositions of HEAs present significant challenges in accurately predicting their phase structures, which is crucial for tailoring their properties for specific applications. This study proposes a machine learning (ML)–based approach to predict HEA phase structures using experimentally validated datasets containing chemical composition–derived features. A Boolean vector technique was employed to encode multiphase classifications, allowing the model to accurately capture complex phase relationships. Four ML algorithms consisting of support vector machine (SVM), k-nearest neighbors (KNN), random forest (RF) and neural network (NN) were utilized to develop predictive models. The models were evaluated using rigorous cross-validation (CV) and tested on unseen data samples. The results demonstrate that NN and KNN outperform other models, achieving an impressive test accuracy of 84.85%. Feature importance analysis reveals that valence election concentration and melting temperature are the most influential factors governing phase formation. This study highlights the effectiveness of ML in accelerating HEA design by significantly reducing reliance on experimental trial-and-error approaches. The predictive models can be applied in alloy design to rapidly screen compositions with desired phase structures, guiding experimental synthesis and optimizing material properties for advanced application. The findings underscore the potential of ML in computational materials science and open new avenues for integration artificial intelligence–driven approaches with conventional metallurgical techniques to enhance HEA development.


  • Open Access

    Machine Learning-Based Prediction of Complex Combination Phases in High-Entropy Alloys

    by Jirapracha Thampiriyanon, Sakhob Khumkoa

    High-entropy alloys (HEAs) have emerged as a novel class of materials that exhibit a wide range of desirable properties making them a focal point for research and potential applications across various industries. The complexity and variability in the compositions of HEAs pose a significant change in predicting their phases, which is crucial for determining their applicability and performance in specific applications. Accurate phase prediction is essential for determining the ideal combination of elements required to design HEAs with targeted properties. This study proposes a machine learning (ML) based approach to predict the phase structure of HEAs utilizing experimental data containing features derived from the chemical composition and corresponding phases. A Boolean vector technique was employed to represent the presence or absence of multiple phase combinations enhancing the model’s ability to accurately capture complex phase structures. Four robust ML algorithms consisting of support vector machine (SVM), k-nearest neighbors (KNN), random forest (RF) and neural network (NN), were employed to develop models capable of classifying the phases of HEAs. The performance of these models was rigorously evaluated through testing on unseen data samples. The findings revealed that both NN and KNN demonstrate superior performance achieving a remarkable test accuracy of 84.85%. This study underscores the potential of ML as an effective tool for predicting the phases of HEAs, offering a new avenue for more innovative approaches to material design and discovery in the future.