Szymon Kiełczawa
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Szymon Kiełczawa has a total of 10 co-authors. Here are the top co-authors by number of shared publications:
- Jaroslaw Domaradzki
Wroclaw University of Science and Technology
4 shared publications - Artur Wiatrowski
Faculty of Electronics, Photonics and Microsystems, Wroclaw University of Science and Technology, Janiszewskiego 11/17, 50-372 Wroclaw, Poland
3 shared publications - Michał Mazur
Wroclaw University of Science and Technology
3 shared publications - Witold Posadowski
Faculty of Electronics, Photonics and Microsystems, Wrocław University of Science and Technology, Janiszewskiego 11/17, 50-372 Wrocław, Poland
3 shared publications - Agata Obstarczyk
Faculty of Electronics, Photonics and Microsystems, Wrocław University of Science and Technology, ul. Janiszewskiego 11/17, 50-372 Wrocław, Poland
1 shared publication - Damian Wojcieszak
Wroclaw University of Science and Technology, Faculty of Electronics, Photonics and Microsystems, Janiszewskiego 11/17, 50-372 Wrocław, Poland
1 shared publication
Latest Publications
- Open Access
Application of Two-Element Zn-Al Metallic Target for Deposition of Aluminum-Doped Zinc Oxide—Analysis of Sputtering Process and Properties of Obtained Transparent Conducting Films
This article analyzes the reactive magnetron sputtering process, using a two-element Zn-Al target, for depositing aluminum-doped zinc oxide (AZO) layers, aimed at transparent electronics. AZO films were deposited on Corning 7059 glass, flexible Corning Willow® glass and amorphous silica substrates. To optimize the process, the study examined the target surface state across varying argon/oxygen ratios. The gas mixture significantly influenced the Al/Zn atomic ratio in the films, affecting their structural, optical and electrical performance. Films deposited at 80/20 argon/oxygen ratio—near the dielectric mode—showed high light transmission (84%) but high resistivity (47.4·10−3 Ω·cm). Films deposited at ratio of 84/16—close to metallic mode—exhibited lower resistivity (1.9·10−3 Ω·cm) but reduced light transmission (65%). The best balance was achieved with an 82/18 ratio, yielding high light transmission (83%) and low resistivity (1.4·10−3 Ω·cm). These findings highlight the critical role of sputtering atmosphere in tailoring AZO layer properties for use in transparent electronics.
Open AccessApplication of Two-Element Zn-Al Metallic Target for Deposition of Aluminum-Doped Zinc Oxide—Analysis of Sputtering Process and Properties of Obtained Transparent Conducting Films
This article analyzes the reactive magnetron sputtering process, using a two-element Zn-Al target, for depositing aluminum-doped zinc oxide (AZO) layers, aimed at transparent electronics. AZO films were deposited on Corning 7059 glass, flexible Corning Willow® glass and amorphous silica substrates. To optimize the process, the study examined the target surface state across varying argon/oxygen ratios. The gas mixture significantly influenced the Al/Zn atomic ratio in the films, affecting their structural, optical and electrical performance. Films deposited at 80/20 argon/oxygen ratio—near the dielectric mode—showed high light transmission (84%) but high resistivity (47.4·10−3 Ω·cm). Films deposited at ratio of 84/16—close to metallic mode—exhibited lower resistivity (1.9·10−3 Ω·cm) but reduced light transmission (65%). The best balance was achieved with an 82/18 ratio, yielding high light transmission (83%) and low resistivity (1.4·10−3 Ω·cm). These findings highlight the critical role of sputtering atmosphere in tailoring AZO layer properties for use in transparent electronics.
- Open Access
- 27 March 2024
- Published by Beilstein Institut in Beilstein Archives
- Vol. 2024 (1) , 18
Application of two-element Zn-Al metallic target for deposition of aluminum-doped zinc oxide - analysis of sputtering process and properties of obtained transparent conducting films
This article presents an analysis of the reactive magnetron sputtering process using a two-element Zn-Al target, with a particular focus on its application for deposition of aluminum-doped zinc oxide layers for transparent electronics. The research encompasses the deposition of AZO layers on standard Corning 7059 glass and flexible Corning Willow® glass. In order to determine optimal process conditions, a detailed analysis of the target surface state was conducted based on the ratio of working gas to reactive gas (argon/oxygen). Significant influence of the sputtering atmosphere ratio on the Al/Zn atomic ratios in the deposited AZO layers was observed, subsequently affecting their optical and electrical properties. Layers deposited in an atmosphere with an 80/20 (argon/oxygen) ratio exhibited a high light transmission coefficient in the visible range (averaging 84%) and high layer resistivity (47.4 · 10-3 Ωcm). On the other hand, layers deposited in an atmosphere with an 84/16 (argon/oxygen) ratio showed low resistivity (1.9 · 10-3 Ωcm) and a light transmission coefficient in the visible range at 65%. The most promising results were obtained for layers deposited in an atmosphere with an 82/18 ratio, characterized by both high light transmission (83%) and low layer resistivity (1.4 · 10-3 Ωcm).
- 27 March 2024
- Published by Beilstein Institut in Beilstein Archives
- Vol. 2024 (1) , 18
Open AccessApplication of two-element Zn-Al metallic target for deposition of aluminum-doped zinc oxide - analysis of sputtering process and properties of obtained transparent conducting films
This article presents an analysis of the reactive magnetron sputtering process using a two-element Zn-Al target, with a particular focus on its application for deposition of aluminum-doped zinc oxide layers for transparent electronics. The research encompasses the deposition of AZO layers on standard Corning 7059 glass and flexible Corning Willow® glass. In order to determine optimal process conditions, a detailed analysis of the target surface state was conducted based on the ratio of working gas to reactive gas (argon/oxygen). Significant influence of the sputtering atmosphere ratio on the Al/Zn atomic ratios in the deposited AZO layers was observed, subsequently affecting their optical and electrical properties. Layers deposited in an atmosphere with an 80/20 (argon/oxygen) ratio exhibited a high light transmission coefficient in the visible range (averaging 84%) and high layer resistivity (47.4 · 10-3 Ωcm). On the other hand, layers deposited in an atmosphere with an 84/16 (argon/oxygen) ratio showed low resistivity (1.9 · 10-3 Ωcm) and a light transmission coefficient in the visible range at 65%. The most promising results were obtained for layers deposited in an atmosphere with an 82/18 ratio, characterized by both high light transmission (83%) and low layer resistivity (1.4 · 10-3 Ωcm).
- Open Access
Effect of Annealing on the Microstructure, Opto-Electronic and Hydrogen Sensing Properties of V2O5 Thin Films Deposited by Magnetron Sputtering
This paper reports results of investigations on selected properties of vanadium oxide thin films deposited using gas impulse magnetron sputtering and annealed at temperatures in the range of 423 K to 673 K. Post-process annealing was shown to allow phase transition of as-deposited films from amorphous to nanocrystalline V2O5 with crystallite sizes in the range of 23 to 27 nm. Simultaneously, annealing resulted in an increase in surface roughness and grain size. Moreover, a decrease in transparency was observed in the visible wavelength range of approximately 50% to 30%, while the resistivity of formed vanadium pentoxide thin films was almost unchanged and was in the order of 102 Ω·cm. Simultaneously, the best optoelectronic performance, testified by evaluated figure of merit parameter, indicated the as-deposited amorphous films. Performed Seebeck coefficient measurements indicated the electron type of electrical conduction of each prepared thin film. Furthermore, gas sensing properties towards diluted hydrogen were investigated for annealed V2O5 thin films, and it was found that the highest senor response was obtained for a thin film annealed at 673 K and measured at operating temperature of 623 K.
Open AccessEffect of Annealing on the Microstructure, Opto-Electronic and Hydrogen Sensing Properties of V2O5 Thin Films Deposited by Magnetron Sputtering
This paper reports results of investigations on selected properties of vanadium oxide thin films deposited using gas impulse magnetron sputtering and annealed at temperatures in the range of 423 K to 673 K. Post-process annealing was shown to allow phase transition of as-deposited films from amorphous to nanocrystalline V2O5 with crystallite sizes in the range of 23 to 27 nm. Simultaneously, annealing resulted in an increase in surface roughness and grain size. Moreover, a decrease in transparency was observed in the visible wavelength range of approximately 50% to 30%, while the resistivity of formed vanadium pentoxide thin films was almost unchanged and was in the order of 102 Ω·cm. Simultaneously, the best optoelectronic performance, testified by evaluated figure of merit parameter, indicated the as-deposited amorphous films. Performed Seebeck coefficient measurements indicated the electron type of electrical conduction of each prepared thin film. Furthermore, gas sensing properties towards diluted hydrogen were investigated for annealed V2O5 thin films, and it was found that the highest senor response was obtained for a thin film annealed at 673 K and measured at operating temperature of 623 K.
- Open Access
Investigation of the Microstructure, Optical, Electrical and Nanomechanical Properties of ZnOx Thin Films Deposited by Magnetron Sputtering
The paper presents the results of an investigation of the influence of technological parameters on the microstructure, optical, electrical and nanomechanical properties of zinc oxide coatings prepared using the pulsed reactive magnetron sputtering method. Three sets of ZnOx thin films were deposited in metallic, shallow dielectric and deep dielectric sputtering modes. Structural investigations showed that thin films deposited in the metallic mode were nanocrystalline with mixed hexagonal phases of metallic zinc and zinc oxide with crystallite size of 9.1 and 6.0 nm, respectively. On the contrary, the coatings deposited in both dielectric modes had a nanocrystalline ZnO structure with an average crystallite size smaller than 10 nm. Moreover, coatings deposited in the dielectric modes had an average transmission of 84% in the visible wavelength range, while thin films deposited in the metallic mode were opaque. Measurements of electrical properties revealed that the resistivity of as-deposited thin films was in the range of 10−4 Ωcm to 108 Ωcm. Coatings deposited in the metallic mode had the lowest hardness of 2.2 GPa and the worst scratch resistance among all sputtered coatings, whereas the best mechanical properties were obtained for the film sputtered in the deep dielectric mode. The obtained hardness of 11.5 GPa is one of the highest reported to date in the literature for undoped ZnO.
Open AccessInvestigation of the Microstructure, Optical, Electrical and Nanomechanical Properties of ZnOx Thin Films Deposited by Magnetron Sputtering
The paper presents the results of an investigation of the influence of technological parameters on the microstructure, optical, electrical and nanomechanical properties of zinc oxide coatings prepared using the pulsed reactive magnetron sputtering method. Three sets of ZnOx thin films were deposited in metallic, shallow dielectric and deep dielectric sputtering modes. Structural investigations showed that thin films deposited in the metallic mode were nanocrystalline with mixed hexagonal phases of metallic zinc and zinc oxide with crystallite size of 9.1 and 6.0 nm, respectively. On the contrary, the coatings deposited in both dielectric modes had a nanocrystalline ZnO structure with an average crystallite size smaller than 10 nm. Moreover, coatings deposited in the dielectric modes had an average transmission of 84% in the visible wavelength range, while thin films deposited in the metallic mode were opaque. Measurements of electrical properties revealed that the resistivity of as-deposited thin films was in the range of 10−4 Ωcm to 108 Ωcm. Coatings deposited in the metallic mode had the lowest hardness of 2.2 GPa and the worst scratch resistance among all sputtered coatings, whereas the best mechanical properties were obtained for the film sputtered in the deep dielectric mode. The obtained hardness of 11.5 GPa is one of the highest reported to date in the literature for undoped ZnO.