Muhammad Waqas Hanif
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Muhammad Waqas Hanif has a total of 26 co-authors. Here are the top co-authors by number of shared publications:
- Muhammad Jawad
Department of Industrial Engineering, Faculty of Industrial Engineering, University of Engineering and Technology, Taxila, Pakistan
6 shared publications - Feroz Haider
Industrial Engineering Department, University of Engineering and Technology, Taxila 47050, Pakistan
4 shared publications Mirza Jahanzaib
Department of Industrial Engineering, University of Engineering and Technology Taxila, Punjab 47050, Pakistan
2 shared publications- Mirza Jahanzaib
Department of Industrial Engineering, Faculty of Industrial Engineering, University of Engineering and Technology, Taxila, Pakistan
2 shared publications Muhammad Sajid
Department of Industrial Engineering, Faculty of Industrial Engineering, University of Engineering and Technology, Taxila, Pakistan
2 shared publications- Muhammad Sajid
Department of Industrial Engineering, University of Engineering and Technology Taxila, Punjab, Pakistan
2 shared publications
Latest Publications
- 26 January 2026
- Published by Springer Nature in Silicon
- Vol. 18 (6) , 2107-2127
Evaluation of SiC Nanoparticles-based Reinforced Casted Filler Effects on the Mechanical Performance of Al-2024 GTAW Welded Joints
- 26 January 2026
- Published by Springer Nature in Silicon
- Vol. 18 (6) , 2107-2127
Evaluation of SiC Nanoparticles-based Reinforced Casted Filler Effects on the Mechanical Performance of Al-2024 GTAW Welded Joints
- 14 November 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (16) , 17214-17234
Evaluating the Influence of Copper Bar Preheating Temperature on the Electromechanical and Microstructural Characteristics of In Situ Heat-Treated 7075Al/Cu Composite Joints
- 14 November 2024
- Published by Springer Nature in Journal of Materials Engineering and Performance
- Vol. 34 (16) , 17214-17234
Evaluating the Influence of Copper Bar Preheating Temperature on the Electromechanical and Microstructural Characteristics of In Situ Heat-Treated 7075Al/Cu Composite Joints
- Open Access
- 20 September 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 75 (1) , 4
Experimental Study on Ultimate Tensile Strength and Impact Energy of Al-2024 Friction Stir-Welded Joints
This paper focuses on the multi-objective optimization of friction stir welding process parameters. Three input variables, including the axial load (AL), tool rotation speed (RS), and tool tilt angle (TA), were selected to optimize the mechanical characteristics of Al-2024 friction stir-welded (FSW) joints. The ultimate tensile strength (UTS) and impact energy (IE) were selected as output responses to measure the mechanical characteristics of Al-2024 FSW joints. A total of nine experiments, using the L9 orthogonal array as part of the Taguchi method, were performed to determine the significance of the process parameters. Gray relational analysis (GRA) was employed to conduct the multi-objective optimization of these combinations of process parameters. The results of the analysis of variance (ANOVA) showed that the AL has the most significant effect on the UTS and IE of Al-2024 FSW joints, followed by the TA and RS. The Taguchi-based GRA analysis revealed that an AL of 10 KN, a TA of 2 degrees, and an RS of 1500 rpm resulted in an optimal UTS of 333.06 MPa and an IE of 40.62 Joules. In these optimal experimental settings, optical microscopy analysis revealed the presence of a recrystallized fine-grain structure in the heat-affected zone of the welded region.
- 20 September 2024
- Published by MDPI AG in Engineering Proceedings
- Vol. 75 (1) , 4
Open AccessExperimental Study on Ultimate Tensile Strength and Impact Energy of Al-2024 Friction Stir-Welded Joints
This paper focuses on the multi-objective optimization of friction stir welding process parameters. Three input variables, including the axial load (AL), tool rotation speed (RS), and tool tilt angle (TA), were selected to optimize the mechanical characteristics of Al-2024 friction stir-welded (FSW) joints. The ultimate tensile strength (UTS) and impact energy (IE) were selected as output responses to measure the mechanical characteristics of Al-2024 FSW joints. A total of nine experiments, using the L9 orthogonal array as part of the Taguchi method, were performed to determine the significance of the process parameters. Gray relational analysis (GRA) was employed to conduct the multi-objective optimization of these combinations of process parameters. The results of the analysis of variance (ANOVA) showed that the AL has the most significant effect on the UTS and IE of Al-2024 FSW joints, followed by the TA and RS. The Taguchi-based GRA analysis revealed that an AL of 10 KN, a TA of 2 degrees, and an RS of 1500 rpm resulted in an optimal UTS of 333.06 MPa and an IE of 40.62 Joules. In these optimal experimental settings, optical microscopy analysis revealed the presence of a recrystallized fine-grain structure in the heat-affected zone of the welded region.
- Open Access
- 19 September 2023
- Published by MDPI AG in Engineering Proceedings
- Vol. 45 (1) , 53
Investigating the Ability of Process Parameters to Reduce Defects during the Drilling of Carbon-Fiber-Reinforced Plastic (CFRP) and Aluminum Stack
The effects of drilling process parameters, such as drill diameter and feed rate, on the delamination of holes has been examined while drilling Carbon-Fiber-Reinforced Plastics and aluminum (CFRP/Al2219-T6). The stack method was employed while drilling in order to reduce the defects in the drilling process and enhance the quality of the holes produced. A total of nine experiments were performed using the central composite design. An analysis of variance (ANOVA) revealed that feed rate and drill size have significant effects on the delamination of holes. The experimental results show that the minimum delamination value (1.018) was obtained at a feed rate of 26.5 mm/min and with a drill diameter of 6.5 mm.
- 19 September 2023
- Published by MDPI AG in Engineering Proceedings
- Vol. 45 (1) , 53
Open AccessInvestigating the Ability of Process Parameters to Reduce Defects during the Drilling of Carbon-Fiber-Reinforced Plastic (CFRP) and Aluminum Stack
The effects of drilling process parameters, such as drill diameter and feed rate, on the delamination of holes has been examined while drilling Carbon-Fiber-Reinforced Plastics and aluminum (CFRP/Al2219-T6). The stack method was employed while drilling in order to reduce the defects in the drilling process and enhance the quality of the holes produced. A total of nine experiments were performed using the central composite design. An analysis of variance (ANOVA) revealed that feed rate and drill size have significant effects on the delamination of holes. The experimental results show that the minimum delamination value (1.018) was obtained at a feed rate of 26.5 mm/min and with a drill diameter of 6.5 mm.
- Open Access
- 7 September 2023
- Published by MDPI AG in Engineering Proceedings
- Vol. 45 (1) , 1
Tool Wear Parameter Optimization in Machining a Squeeze-Cast Metal Matrix Composite (Al6061-SiC)
In this research work, machining operations on an aluminum matrix composite (AMC) were optimized for improving the wear of high-speed steel tools. The squeeze casting method was used to manufacture the AMC, which had Al-6061 as matrix material and silicon carbide (wt. 15%) microparticles used as reinforcement. Feed rate (Fr), cutting speed (Cs), and depth of cut (Dc) were selected to optimize HSS tool wear rate. Using the Box–Behnken design, seventeen experiments were performed to analyze the single-factor effects and interaction effects of the process parameters on HSS tool wear rate. Experimental results show that optimal tool wear (0.964) was achieved at a Cs of 80 m/min, Fr of 0.2 rev/min, and Dc of 0.8 mm.
- 7 September 2023
- Published by MDPI AG in Engineering Proceedings
- Vol. 45 (1) , 1
Open AccessTool Wear Parameter Optimization in Machining a Squeeze-Cast Metal Matrix Composite (Al6061-SiC)
In this research work, machining operations on an aluminum matrix composite (AMC) were optimized for improving the wear of high-speed steel tools. The squeeze casting method was used to manufacture the AMC, which had Al-6061 as matrix material and silicon carbide (wt. 15%) microparticles used as reinforcement. Feed rate (Fr), cutting speed (Cs), and depth of cut (Dc) were selected to optimize HSS tool wear rate. Using the Box–Behnken design, seventeen experiments were performed to analyze the single-factor effects and interaction effects of the process parameters on HSS tool wear rate. Experimental results show that optimal tool wear (0.964) was achieved at a Cs of 80 m/min, Fr of 0.2 rev/min, and Dc of 0.8 mm.
- Open Access
- 13 June 2023
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 381, 02006
Optimizing the process parameters of Fiction Stir Welded dissimilar 2024Al-5754Al Joint using the Taguchi Method
It is a requirement of modern age industries, especially the aerospace, automobile, and shipbuilding sectors, to manufacture high strength and low weight dissimilar aluminium alloy welded joints. Therefore, the aim of this project is to investigate the effect of tool rotation speed, feed rate, and pin type on the ultimate tensile strength (UTS) of dissimilar aluminium alloys (2024 Al and 5754 Al) in friction stir welded joints. Nine experiments have been performed using an orthogonal array (L9) of the Taguchi method. An analysis of variance (ANOVA) established that pin type is the most prominent parameter, followed by tool rotation speed and feed rate. The optimal value of ultimate tensile strength (268 MPa) was achieved at 1.5 mm/s feed rate, 1600 rpm speed, and type 1 of pin. A confirmation test shows that there is a high correlation between the estimated and actual values of UTS.
- 13 June 2023
- Published by EDP Sciences in MATEC Web of Conferences
- Vol. 381, 02006
Open AccessOptimizing the process parameters of Fiction Stir Welded dissimilar 2024Al-5754Al Joint using the Taguchi Method
It is a requirement of modern age industries, especially the aerospace, automobile, and shipbuilding sectors, to manufacture high strength and low weight dissimilar aluminium alloy welded joints. Therefore, the aim of this project is to investigate the effect of tool rotation speed, feed rate, and pin type on the ultimate tensile strength (UTS) of dissimilar aluminium alloys (2024 Al and 5754 Al) in friction stir welded joints. Nine experiments have been performed using an orthogonal array (L9) of the Taguchi method. An analysis of variance (ANOVA) established that pin type is the most prominent parameter, followed by tool rotation speed and feed rate. The optimal value of ultimate tensile strength (268 MPa) was achieved at 1.5 mm/s feed rate, 1600 rpm speed, and type 1 of pin. A confirmation test shows that there is a high correlation between the estimated and actual values of UTS.
- 17 December 2022
- Published by Springer Nature in China Foundry
- Vol. 20 (1) , 29-39
Evaluation of microstructure and mechanical properties of squeeze overcast Al7075−Cu composite joints
- 17 December 2022
- Published by Springer Nature in China Foundry
- Vol. 20 (1) , 29-39
Evaluation of microstructure and mechanical properties of squeeze overcast Al7075−Cu composite joints