Current Organizations / Institutes

The organizations/institutes from the scholar's latest article


Yanwei Li has a total of 87 co-authors. Here are the top co-authors by number of shared publications:


Latest Publications

  • Open Access

    A new experimental set up to study the partition of energy upon hypervelocity impacts of micrometeorites onto a variety of solid targets

    by Anna Mocker, Florian Behrens, Benedict Dillmann, Simon Dürrstein, Elias Ehrhard, Chanjeev Jeyecumar, David Nestle, Yan-Wei Li, Benedict Ngyuen, Johannes Schmid, et al.

    Background and motivationHypervelocity impacts with impact speed above about 3-4 km-1 of micro-meteoroites onto solid surfaces are an ubiquitous phenomenon throughout the Solar System. These particles are between a few nm up to several µm in size and are comprised by interstellar and interplanetary dust. Impacts at such high speeds exceeding the speed of sound within the materials in question lead to inertial stresses upon impact that are very high compared to the strength of these materials. This causes the material to behave like fluids under the impact.Due to the their ubiquity and the high impact energy leading to extremely high temperatures and pressures in the affected materials, the physical processes caused by HVIs play an important role in a variety of fields such as the investigation of matter at extreme pressures and temperature, shock waves in solid bodies or even Solar System research, planetology, cosmic dust research and space engineering.An 2MV electrostatic dust acceleratorA major part of what we know today of HVIs of micro meteoroids was obtained in theprocess of developing, calibrating and operation of in situ instruments for the investigationof dust in the Solar System.These particles are between a few nm up to several µm in size and interact with thesolid surface of the instrument: they impact at speeds of several hundred m s−1 to severalhundred km s−1. Thereby induced physical processes generate measurable signals whichare then transmitted to Earth and can be analysed afterwards.There are a variety of methods for in situ dust measurements such as the detection ofthin foil penetration, the particle charge, the emerging impact flash or ions generated uponimpact, revealing the particles’ velocity, trajectory, mass and even chemical compositionTo calibrate in-situ dust instruments and to get a deeper understanding of the processes involved, hypervelocity impact measurements under similar and well defined conditions are required. For this purpose, a Van-de-Graaff type ion accelerator was modified at the MPI-K/HD in the late 1960ies. The accelerator was equipped with a dust source capable of charging and accelerating dust particles.The accelerator covers a large portion of the speed and size ranges needed for most cosmic applications with velocities between 1 to about 80 km s−1 .Impacts onto solid surfaces and the partition of energyA fast particle impacting a solid surface causes mechanical stress in the particle and the target body, generating compression and even shock waves depending on the impact velocity. Subsequently the particles and the affected target area are compressed to high pressures and temperatures. This increase in internal specific energy is then partitioned into a variety of processes leading to a number of phenomena:Surface alteration and cratering,generation of ions and neutral gas atoms (impact plasma)glow of the impact plasma cloudgeneration of secondary particles (ejecta).The resulting observables of HVIs (Fig. 1) are a function of projectile and target material, impact velocity, incident angle and the mass and shape of the projectile. This allows to use the quantitative investigation of these phenomena to deduce information about the impacting particles and the impact parameters and to gain a deeper understanding of the impact and its subsequent processes.An experimental set up to study simultaneously the impact plasma and the generation of secondary particles We will present a new experimental set up designed and build to allow to measure as many resulting observables as possible simultaneously. Furthermore, it allows for a wide variety of target materials form metal and silicate materials to even ice and ice-silicate mixtures.The experimental set up is implemented into the beam line of the dust accelerator in an angle of 45 degree and consists ofa cylindrical vacuum camber allowing attach additional detectors to the chamber in addition to the linear time-of-flight mass spectrometer set up in the chamber. A newly designed and built high-vacuum chamber allows simultaneous measurements of the ion and neutral generation and the simultaneous recording of the surface alteration. Eight flanges are provided for feed-throughs, windows and interface for the particle beam.A small cubic vacuum chamber serving as an airlock to insert various target materials in ti the vacuum of the set up.A linear feedthrough to move the target from the airlock very precisely into the detector set up as well as providing a cooling channel to allow the use of ices and ice-silicate mixtures as targets.This unique set up allows toCharacterise of the emerging plasma, with a linear TOF mass spectrometer. This allows to investigate the thermodynamical properties of the impact plasma leading to a deeper understanding of the process of impact ionisation and the behaviour of matter under extreme conditions.The generation of secondary particles is characterised by measuring the number of generated particles, their mass and velocity distribution as well as their angular distribution with a delay line detector.Additionally a residual gas analyser will be used to measure the neutral component of the impact plasmaConclusion and outlookWe would like to present: A short overview the simulation of HVIs of micrometeorites in the laboratory using a 2MV electrostatic dust accelerator at the University of Stuttgart.The overall design of the experimental set up A report of the first test of the set up.-The status and outlook for the planned experimental programme for the characterisation and description of the HVI onto silicate-ice mixtures due to the generation of ions and their properties with a linear time-of-flight mass spectrometer, as well a the generation of secondary particles and of neutral gas production.This experimental work in combination with future theoretical studies of the impact process and the subsequent expansion of the impact generated...

  • Open Access

    Deciphering mixtures of complex organic compounds in cosmic dust particles using JAXA's Destiny+ Dust Analyzer

    by Nozair Khawaja, Ralf Srama, Derek H. H. Chan, Jonas Simolka, Steven P. Armes, Rebecca Mikula, Takayuki Hirai, Yanwei Li, Heiko Strack, Thomas R. O'SUllivan, et al.

    Organic compounds are a ubiquitous component of cosmic dust and provide insight into the origin of planetary systems, the availability of carbon for life in the solar system and beyond, and the distribution of potential biosignatures in the universe. Compositional and dynamical analysis of such dust grains can shed insight into their origin. The Destiny Dust Analyzer (DDA) onboard JAXA’s interplanetary space mission DESTINY+ will detect and analyse the composition of (sub-)micron sized dust ejecta during flybys of asteroids Apophis and Phaethon [1,2]. DDA will characterise both interplanetary and interstellar dust grains during the mission’s lifetime [3]. DDA is an impact ionisation time-of-flight mass spectrometer, whereby dust particles incident onto the instrument’s target at hypervelocity (≥ 2 km s-1) vaporise and partially fragment into various constituent ions and neutrals. Here, we investigate the capability of DDA to detect a mixture of complex organic compounds in single cosmic dust particles. An organic cosmic dust analogue is prepared by coating polycyclic aromatic hydrocarbon, perylene (C20H12), microparticles with an ultrathin overlayer of a conductive polymer, polypyrrole H(C4H2NH)nH, to enable acceleration up to hypervelocities with a high-voltage van de Graaff instrument. Time-of-flight mass spectra obtained at impact speeds ~3-20 km/s are recorded in this calibration campaign. The characteristic parent molecular ion for perylene, [C20H12 (+H)]+, is observed at m/z 251 ± 1 in mass spectra arising from impacts between 3 and 8 km s-1. However, between 8 and 18 km s-1, no such parent ion is observed. Instead, impact ionisation mass spectra exhibit a characteristic series of homologous [CnHm]+ fragments originating from both polypyrrole and perylene, alongside some non-sequential ions which may be diagnostic for distinguishing between different organic components in cosmic dust. The contributions of each species to fragmentation patterns in the mass spectra is coupled with the impact velocity. Our results are in agreement with Mikula et al. (2024), who investigated impact ionisation of polypyyrole-coated anthracene particles for the Interstellar Dust EXperiment (IDEX) onboard NASA's Interstellar Mapping and Acceleration Probe (IMAP), and observed a similar relationship between fragmentation pattern and velocity [4].Additional experiments with a range of PAHs, heterocycles, and lower mass organics at various velocities, will yield further insight into the detection and characterisation of heterogeneous dust likely to be encountered by DDA. Similarly, theoretical chemical calculations could assist in deciphering the contribution of different species to mass spectral features via the analysis of dissociation thermodynamics and kinetics.[1] Ozaki et al. (2022) https://doi.org/10.1016/j.actaastro.2022.03.029[2] Simolka et al. (2024) https://doi.org/10.1098/rsta.2023.0199[3] Krüger et al. (2024) https://doi.org/10.1016/j.pss.2024.106010[4] Mikula et al. (2024) https://doi.org/10.1021/acsearthspacechem.3c00353

  • Open Access

    Small Linear Accelerators for Charged Microparticles

    by Yanwei Li, Marcel Bauer, Ralf Srama, Florian Behrens, Felix Schäfer, Anna Mocker, Jonas Simolka, Heiko Strack

    Researching cosmic dust requires terrestrial facilities for accelerating analogues of different sizes and masses. To address the area of very lightweight particles, electrostatic accelerators like Van-de-Graaf accelerators or Linear Accelerators (LINACs) have proven adequate. A new variable frequency switched 6-stage LINAC of 120 kilovolts (kV) potential was built at the Institute of Space Systems, University of Stuttgart. It utilizes negative voltages, no storage-capacitors, isometric drift tubes, one semiconductor-based high-voltage switch per stage and there is no voltage drop during acceleration. The electronics limit the particle rate at 33 particles per second. By setting a target speed window, the control software and circuitry autonomously chooses the right amount of acceleration-stages to meet that requirement, if possible. Micron-sized iron particles were accelerated successfully achieving speed increase rates of up to 3-times the pre-LINAC speed and a total speed of up to 1300 meters per second (m/s). This platform provides a new tool for dust sensor calibration, impact physics and material surface processing due to its ability to bring particles of different charge-to-mass ratios to a defined target speed. To further increase the speed, mass and ratio of accelerated microparticles, a new setup is under construction. It will utilize 20 stages with up to 25 kV potential each, resulting in a total acceleration potential of 500 kV. The theoretically achievable particle rate for particles between 500 m/s and 2 km/s will be 1000 particles per second.

  • Open Access

    A Small Linear Accelerator for Charged Microparticles

    by Marcel Bauer, Yanwei Li, Ralf Srama, Florian Behrens, Anna Mocker, Felix Schäfer, Jonas Simolka, Heiko Strack

    Researching cosmic dust requires terrestrial facilities for accelerating analogues of different sizes and masses. To address the area of very lightweight particles, electrostatic accelerators like Van de Graaf accelerators or Linear Accelerators (LINACs) have proven adequate. This article describes the components, dimensions, working principle and attributes of a variable frequency switched 6-stage LINAC of 120 kilovolts (kV) potential based at the Institute of Space Systems, University of Stuttgart. It utilizes negative voltages, no storage capacitors, isometric drift tubes, one semiconductor-based high-voltage switch per stage and there is no voltage drop during acceleration. The particle rate can reach up to 33 particles per second. By setting a target speed window, it autonomously chooses the right number of acceleration stages to meet that requirement, if possible. Micron-sized iron particles were accelerated successfully, achieving speed increase rates of up to three times the pre-LINAC speed and a total speed of up to 1300 m/s. This platform provides a new tool for dust sensor calibration, impact physics and material surface processing due to its ability to bring particles of different charge-to-mass ratios to a defined target speed.

  • Open Access

    The DESTINY+ Dust Analyser (DDA) for in-situ Cosmic Dust Measurements

    by Ralf Srama, Denis Acker, Tomoko Arai, Marcel Bauer, Andre Beck, Patrick Fröhlich, Michael Greaesslin, Carsten Henselowsky, Takayuki Hirai, Stephan Ingerl, et al.

    The DESTINY+ mission, led by the Japan Aerospace Exploration Agency (JAXA), offers a distinctive opportunity for in-situ measurements of cosmic dust. Scheduled for launch in 2028, the spacecraft will use electric propulsion during its interplanetary trajectory toward its target, the active asteroid (3200) Phaethon. A high-speed flyby of Phaethon, with a relative velocity of 35 km/s, is a key mission objective.The mission's primary scientific payload, the Destiny Dust Analyser (DDA), is being developed by the University of Stuttgart, Germany, in partnership with von Hoerner Sulger GmbH. The DDA’s goal is to characterize the cosmic dust environment encountered along the trajectory through in-situ analysis of individual dust particles. These dust populations range from space debris and interplanetary/interstellar dust to ejecta particles from the lunar surface and Phaethon itself. During the flyby, should Phaethon exhibit activity, dust particles originating from its interior may also be analyzed.Equipped with a trajectory sensor, the DDA measures the primary surface charge, trajectory, and velocity of individual dust grains. It further conducts compositional analysis via time-of-flight (TOF) mass spectrometry of the impact plasma generated when dust grains collide with the instrument’s target. The charge generated in the impact plasma is also measured, offering additional insights into particle properties.This paper outlines the DDA’s instrument configuration, provides an update on its development status, and demonstrates its performance using recent TOF mass spectra. Testing has included both positive and negative polarity modes, enabling comparisons of anion and cation mass spectra. Such comparisons are particularly valuable for analyzing organic-rich dust particles.

  • Open Access

    Review of: "Ballistic Motion of Dust Particles in the "Collecting the Big Muley Lunar Rock" Sequence of the Apollo XVI Footage"

    by Yanwei Li

    The authors employed 2D and 3D photoanalytical methods and techniques to analyze the photos and films taken during the Apollo XVI mission. They specifically studied the motion of dust particles kicked up by the astronauts’ footsteps. The analysis met...

  • Open Access

    Calibration of Destiny Dust Analyzer (DDA) with Polypyrrole Coated Perylene Microparticles

    by Nozair Khawaja, Ralf Srama, Derek Chan, Steven Armes, Li Yanwei, Jonas Simolka, Heiko Strack, Anna Mocker, Jon Hillier, Frank Postberg, et al.

    DESTINY+(Demonstration and Experiment of Space Technology for INterplanetary voYage with Phaethon fLyby and dUst Science) is a future JAXA interplanetary space mission to the active asteroid 3200 Phaethon (Ozaki et al. 2022). The primary scientific payload - the Destiny Dust Analyzer (DDA; Simolka et al. 2024), an impact ionisation mass spectrometer - will assess physicochemical properties of (sub-)micron-sized dust particles emitted by Phaethon. Over the mission duration, DDA will also sample dust particles originating from different environments: lunar, interplanetary, and interstellar. DDA is a time of flight (TOF) impact ionisation mass spectrometer - a successor to Cassini’s Cosmic Dust Analyzer (CDA; Srama et al. 2004), which sampled ice and dust from the Saturnian system - and similar to Europa Clipper’s SUrface Dust Analyzer (SUDA; Kempf et al. in review) that will visit the Jovian moon Europa. These instruments utilise impact ionization; nanometere- to micron-sized dust particles strike the instrument’s target at hypervelocities, ionising chemical species embedded within particles and generating a TOF mass spectrum.Both for calibration of DDA and the generation of a cationic mass spectral library to characterise the composition of dust in space, laboratory experiments are currently underway using DDA’s engineering model. Polycyclic Aromatic Hydrocarbons (PAHs) are ubiquitous organic compounds in many different space and planetary environments – e.g. they are a major constituent of carbonaceous chondrites. For this reason, we investigate polypyrrole coated perylene PAH particles prepared in the form of microparticles and accelerate them using a Van de Graaff dust accelerator. Here, we present the first analysis of the cationic TOF mass spectra of such particles accelerated at 750 kV and recorded over an impact speeds range of 3-36 km/s. The spectra successfully exhibit mass line corresponding to the molecular ion [M]+ of perylene at m/z 252 for impact speeds between 3 and 7 km/s. From impact speeds of 9 to 16 km/s, the spectra exhibit a sequence of consecutive mass lines above m/z 45 with mass resolution ∆m ≈ 12-14, sufficient to characterise a homologous series of cations from PAHs. In addition, these spectra also show low mass fragment cations that most likely arise from the coating material of polypyrrole and from target contamination.Future work will investigate these particles accelerated over higher potential differences up to 2 MV, as well as the mass spectral appearance of other PAHs. This carries relevance not only for DDA, but also for other impact ionisation mass spectrometers onboard future space missions (e.g., SUDA onboard NASA’s Europa-Clipper) that look to sample interplanetary and interstellar dust.ReferencesKempf et al. (2024), SUDA: A SUrface Dust Analyser for compositional mapping of the Galilean moon Europa. Space Science Reviews, in review.Ozaki N et al. (2022), Mission design of DESTINY +: Toward active asteroid (3200) Phaethon and multiple small bodies. Acta Astronaut. 196 , 42–56.Srama et al. (2004), The Cassini Cosmic Dust Analyser. Space Sci. Rev., 114, 465–518.Simolka et al. (2024) The DESTINY+ Dust Analyser — a dust telescope for analysing cosmic dust dynamics and composition. Phil. Trans. R. Soc. A 382: 20230199.

  • Open Access

    In Situ Cosmic Dust Detection for Heliophysics

    by Hsiang-Wen Hsu, Andrew Poppe, Jamey Szalay, Mihaly Horanyi, Veerle Sterken, Thomas Y. Chen, Ingrid Mann, Mitchell M. Shen, Priscilla C. Frisch, Sigrid Elschot, et al.

    Whitepaper #176 in the Decadal Survey for Solar and Space Physics (Heliophysics) 2024-2033. Main topics: basic research. Additional topics: outer heliosphere; space-based missions/projects; emerging opportunities.

  • Open Access

    Upgrades of a Small Electrostatic Dust Accelerator at the University of Stuttgart

    by Yanwei Li, Marcel Bauer, Sebastian Kelz, Heiko Strack, Jonas Simolka, Christian Mazur, Maximilian Sommer, Anna Mocker, Ralf Srama

    In this paper, we describe the upgrade of a small electrostatic dust accelerator located at the University of Stuttgart. The newly developed dust source, focusing lens, differential detector and linac stage were successfully installed and tested in the beam line. The input voltage range of the dust source was extended from 0–20 kV to 0–30 kV. A newly developed dust detector with two differential charge sensitive amplifiers is employed to monitor particles with speeds from several m/s to several km/s and with surface charges above 0.028 fC. The post-stage linac provides an additional acceleration ability with a total voltage of up to 120 kV. The entire system of this dust accelerator works without protection gas and without a complex high voltage terminal. The volumes to be pumped down are small and can be quickly evacuated. The new system was used to accelerate micron- and submicron-sized metal particles or coated mineral materials. Improvements in the acceleration system allow for a wider variety of dust materials and new applications.


  • Open Access

    A Dynamic Model for the Lunar Ejecta Dust Cloud

    by Maximilian Sommer, Yanwei Li, Ralf Srama, Peter Strub, Jianqun Yang, Xingji Li

    The return to the Moon pushed forward by space agencies as well as private companies around the world, has rekindled interest in the Lunar dust environment, which was identified as a major factor in spacecraft safety and reliability considerations during the Apollo missions. Orbiting the Moon from 2013 to 2014, the Lunar Atmosphere and Dust Environment Explorer (LADEE) gathered conclusive evidence for the existence of a permanent, asymmetric dust cloud around the Moon [1]. Micron-sized ejecta particles generated at impact of interplanetary meteoroids on the Lunar surface act as the main source of this high-altitude dust exosphere, which shows a variable density in dependence of annual meteoroid showers.Here we report on the development of a dynamic model for the lunar ejecta dust cloud. This model simulates cloud particles in a Monte-Carlo fashion, drawing on a combination of existing engineering models and results from hypervelocity impact experiments as model inputs: To emulate the influx of meteoroids we use the Interplanetary Meteoroid Environment Model 2 (IMEM2) [2], developed under ESA contract, as well as a comet stream model based on meteor shower zenith-hourly-rates [3, 4]. To determine angular, velocity, and size distributions of ejecta particles, we resort to three different methods: (1) We use the software Ansys Autodyn to numerically model ejecta particles generated at hypervelocity impacts. (2) Impact experiments with a light-gas gun have been conducted at the Harbin Institute of Technology, to derive ejecta distributions generated by bigger projectiles. (3) We intend to conduct hypervelocity impact experiments with lunar soil simulant at the electrostatic dust-accelerator facility at the University of Stuttgart. The novel experiment set-up, which uses a delay-line-detector to measure micron-sized ejecta particles has recently been verified [5]. Ultimately, the simulated dust ejecta cloud will be fitted to LADEE/LDEX data. This poster-presentation gives an overview of the project and its various modules.References:[1] Horányi, M., et al. "A permanent, asymmetric dust cloud around the Moon." Nature 522.7556 (2015): 324-326.[2] Soja, R. H., et al. "IMEM2: a meteoroid environment model for the inner solar system." Astronomy & Astrophysics 628 (2019): A109.[3] Jenniskens, Peter. "Meteor stream activity I. The annual streams." Astronomy and Astrophysics 287 (1994): 990-1013.[4] McBride, Neil. "The importance of the annual meteoroid streams to spacecraft and their detectors." Advances in Space Research 20.8 (1997): 1513-1516.[5] Li, Yanwei, et al. "Measurement of fragments generated by hypervelocity impacts of micron-sized iron particles at grazing incidents." Advances in Space Research 69.6 (2022): 2629-2635.