Gabriel Liaño
Current Organizations / Institutes
The organizations/institutes from the scholar's latest article
Research Subjects
Gabriel Liaño has a total of 3 co-authors. Here are the top co-authors by number of shared publications:
- José Jiménez-Varona
National Institute of Aerospace Technology, 28850 Madrid, Spain
3 shared publications - José Luis Castillo
UNED
1 shared publication - Pedro Luis García Ybarra
UNED
1 shared publication
Latest Publications
- Open Access
Fineness Ratio Effects on the Flow Past an Axisymmetric Body at High Incidence
The flow past an axisymmetric body at a sufficiently high angle of attack becomes asymmetric and unsteady. Several authors identified three different flow regions for bodies of large fineness ratio at low subsonic flow and high incidence: a steady region in the forebody and two unsteady regions in the rear body. Unsteady Reynolds Averaged Navier–Stokes (URANS) codes with eddy viscosity turbulence models or Reynolds stress turbulence models fail to capture the unsteady flow region. These methods are overly dissipative and resolve only frequencies far lower than turbulent fluctuations. Scale-Adaptive-Simulation (SAS) provides an alternative method to afford the problem of these massively separated flows at high Reynolds numbers without addressing the problem to Large Eddy Simulation (LES). This paper applies SAS to study the effect of slenderness on the flow. The numerical solutions show that the flow becomes more unstable as the fineness ratio increases, and the three flow regions are clearly recognizable. For low fineness ratios, only one of the two unsteady regions is visible. The good agreement between the sectional forces and pressure coefficients with their corresponding experimental data for an ogive-cylinder configuration allows an analysis of the flow structure with a fair degree of confidence.
Open AccessFineness Ratio Effects on the Flow Past an Axisymmetric Body at High Incidence
The flow past an axisymmetric body at a sufficiently high angle of attack becomes asymmetric and unsteady. Several authors identified three different flow regions for bodies of large fineness ratio at low subsonic flow and high incidence: a steady region in the forebody and two unsteady regions in the rear body. Unsteady Reynolds Averaged Navier–Stokes (URANS) codes with eddy viscosity turbulence models or Reynolds stress turbulence models fail to capture the unsteady flow region. These methods are overly dissipative and resolve only frequencies far lower than turbulent fluctuations. Scale-Adaptive-Simulation (SAS) provides an alternative method to afford the problem of these massively separated flows at high Reynolds numbers without addressing the problem to Large Eddy Simulation (LES). This paper applies SAS to study the effect of slenderness on the flow. The numerical solutions show that the flow becomes more unstable as the fineness ratio increases, and the three flow regions are clearly recognizable. For low fineness ratios, only one of the two unsteady regions is visible. The good agreement between the sectional forces and pressure coefficients with their corresponding experimental data for an ogive-cylinder configuration allows an analysis of the flow structure with a fair degree of confidence.
- Open Access
Roughness Effect on the Flow Past Axisymmetric Bodies at High Incidence
The flow at low Mach numbers and high angles of attack over axisymmetric configurations is not symmetric. The mechanism that triggers the asymmetry is a combination of a global (temporal) instability and a convective (spatial) instability. This latter instability is caused by roughness and other geometrical imperfections, which lead to roll angle dependent forces. The flow at these conditions has a complex vortex sheet structure, with two or three different flow regions. An accurate simulation by means of Computational Flow Dynamics (CFD) is thus very challenging, and many researchers have therefore employed Large Eddy Simulation (LES) codes. This study demonstrates that Unsteady Reynolds Averaged Navier-Stokes (URANS) methods are a suitable alternative, if Scale Adaptive Simulation (SAS) is used. This method is capable of capturing the main flow features, provided that fine meshes, which achieve geometrical similarity between the meshed geometry and the real object, and small-time steps are used. It is also demonstrated that, by using URANS methods in combination with SAS, strong differences in the global and local forces depending on the surface roughness of the model are obtained, a result which coincides with several wind tunnel tests.
Open AccessRoughness Effect on the Flow Past Axisymmetric Bodies at High Incidence
The flow at low Mach numbers and high angles of attack over axisymmetric configurations is not symmetric. The mechanism that triggers the asymmetry is a combination of a global (temporal) instability and a convective (spatial) instability. This latter instability is caused by roughness and other geometrical imperfections, which lead to roll angle dependent forces. The flow at these conditions has a complex vortex sheet structure, with two or three different flow regions. An accurate simulation by means of Computational Flow Dynamics (CFD) is thus very challenging, and many researchers have therefore employed Large Eddy Simulation (LES) codes. This study demonstrates that Unsteady Reynolds Averaged Navier-Stokes (URANS) methods are a suitable alternative, if Scale Adaptive Simulation (SAS) is used. This method is capable of capturing the main flow features, provided that fine meshes, which achieve geometrical similarity between the meshed geometry and the real object, and small-time steps are used. It is also demonstrated that, by using URANS methods in combination with SAS, strong differences in the global and local forces depending on the surface roughness of the model are obtained, a result which coincides with several wind tunnel tests.
- Open Access
- 28 September 2022
- Published by MDPI AG in Computation
- Vol. 10 (10) , 173
Numerical Study of the Influence of the Geometrical Irregularities on Bodies of Revolution at High Angles of Attack
The flow at high angles of attack over axisymmetric configurations is not symmetric. The mechanism that triggers the asymmetry may be a combination of a global or hydrodynamic instability (temporal instability) combined with a convective instability (spatial instability) due to microscopic irregularities of the configuration. Poor repeatability of experiments and large differences in the global forces have been obtained with very small changes of the nose tip. In order to study theoretically this phenomenon, numerical simulations have been conducted for an ogive-cylinder configuration at subsonic flow and high angle of attack. For the numerical prediction of the flow about a missile type configuration, an assessment of the effect of structured and unstructured meshes is very important. How the body surface is modelled is very relevant; especially the tip zone of the body. Either configuration resembles a smooth or a rough model. The effect of the turbulence models is also decisive. The analysis has led to the conclusion that only Reynolds stress turbulence models (RSM) combined with Scale Adaptive Simulation (SAS), are the appropriate theoretical tools for the characterization of this flow. The geometrical similarity is very important. There is a roll or orientation angle effect for the unstructured grid, while the structured grid presents a bi-stable solution, one mirror of each other.
- 28 September 2022
- Published by MDPI AG in Computation
- Vol. 10 (10) , 173
Open AccessNumerical Study of the Influence of the Geometrical Irregularities on Bodies of Revolution at High Angles of Attack
The flow at high angles of attack over axisymmetric configurations is not symmetric. The mechanism that triggers the asymmetry may be a combination of a global or hydrodynamic instability (temporal instability) combined with a convective instability (spatial instability) due to microscopic irregularities of the configuration. Poor repeatability of experiments and large differences in the global forces have been obtained with very small changes of the nose tip. In order to study theoretically this phenomenon, numerical simulations have been conducted for an ogive-cylinder configuration at subsonic flow and high angle of attack. For the numerical prediction of the flow about a missile type configuration, an assessment of the effect of structured and unstructured meshes is very important. How the body surface is modelled is very relevant; especially the tip zone of the body. Either configuration resembles a smooth or a rough model. The effect of the turbulence models is also decisive. The analysis has led to the conclusion that only Reynolds stress turbulence models (RSM) combined with Scale Adaptive Simulation (SAS), are the appropriate theoretical tools for the characterization of this flow. The geometrical similarity is very important. There is a roll or orientation angle effect for the unstructured grid, while the structured grid presents a bi-stable solution, one mirror of each other.